BMW 3-Series (E90 E92) Forum - View Single Post

Sal Collaziano · 12-10-2009, 10:18 PM

The yellow engine light that came on was kinda half lit-up.. After doing some reading, it appears that was limp mode.. Correct? If so, maybe I need to turn down the JB+ a bit. I don't want to have to worry about getting put into limp mode if I flex the car's muscle.. What do you think? Anyway, here were my codes before I cleared them:

Short Test

MSD80/MSD81 Engine module for N54
Current Fault Codes

2A87: 2A87 Outlet-Vanos variable cam control test, mechanics Error will cause a warning light Error is not currently present Test conditions have been completed  Freeze Frame Information
Event 1

3100: 3100 boost-pressure control, deactivation Error will not cause a warning light Error is not currently present Test conditions have been completed  

Car Access System 3
Current Fault Codes

A0B0: ECU input brake lights Error will not cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption  

A10A: EWS4 timing challenge/response error Error will not cause a warning light Error is not currently present Test conditions have been completed Signal or value below threshold  

Instrument cluster PL2 E8x and E9x
Current Fault Codes

A3B2: CAN ID 130 error: Clamp status Error will not cause a warning light Error is not currently present Test conditions have been completed  

MOST / CAN gateway CD73/MD73
Current Fault Codes

E194: No CLAMP_STATUS via CAN received Error will not cause a warning light Error is not currently present Test conditions have been completed  

E18C: Device didn't accept or confirm monitoring message (Error_Monitoring) Error will not cause a warning light Error is not currently present Test conditions have been completed  

E18D: Wake Up Device tried to wake up network 3-times without success (Error_WakeUp_Failed) Error will not cause a warning light Error is not currently present Test conditions have been completed  

Telematic control module
Current Fault Codes

A36B:  Error will not cause a warning light Error is not currently present Test conditions have been completed  

A392:  Error will not cause a warning light Error is not currently present Test conditions have been completed  

12-10-2009, 10:18 PM	#44
Sal Collaziano Lieutenant 56 Rep 424 Posts Drives: 2015 BMW X5 Join Date: Jul 2008 Location: Royal Palm Beach, Florida iTrader: (0) Garage List 2007 335i [0.00]	These were all my fault codes.. I cleared them.. Anything to worry about? The yellow engine light that came on was kinda half lit-up.. After doing some reading, it appears that was limp mode.. Correct? If so, maybe I need to turn down the JB+ a bit. I don't want to have to worry about getting put into limp mode if I flex the car's muscle.. What do you think? Anyway, here were my codes before I cleared them: Short Test MSD80/MSD81 Engine module for N54 Current Fault Codes 2A87: 2A87 Outlet-Vanos variable cam control test, mechanics Error will cause a warning light Error is not currently present Test conditions have been completed  Freeze Frame Information Event 1 3100: 3100 boost-pressure control, deactivation Error will not cause a warning light Error is not currently present Test conditions have been completed   Car Access System 3 Current Fault Codes A0B0: ECU input brake lights Error will not cause a warning light Error is not currently present Test conditions have been completed Short circuit or signal interruption   A10A: EWS4 timing challenge/response error Error will not cause a warning light Error is not currently present Test conditions have been completed Signal or value below threshold   Instrument cluster PL2 E8x and E9x Current Fault Codes A3B2: CAN ID 130 error: Clamp status Error will not cause a warning light Error is not currently present Test conditions have been completed   MOST / CAN gateway CD73/MD73 Current Fault Codes E194: No CLAMP_STATUS via CAN received Error will not cause a warning light Error is not currently present Test conditions have been completed   E18C: Device didn't accept or confirm monitoring message (Error_Monitoring) Error will not cause a warning light Error is not currently present Test conditions have been completed   E18D: Wake Up Device tried to wake up network 3-times without success (Error_WakeUp_Failed) Error will not cause a warning light Error is not currently present Test conditions have been completed   Telematic control module Current Fault Codes A36B:  Error will not cause a warning light Error is not currently present Test conditions have been completed   A392:  Error will not cause a warning light Error is not currently present Test conditions have been completed   __________________ Sal Collaziano Stinger Forum Last edited by Sal Collaziano; 12-10-2009 at 11:57 PM..
	Appreciate 0 Quote