View Single Post
      03-24-2009, 10:17 AM   #1
cocoturkey
Lieutenant
Taiwan
15
Rep
441
Posts

Drives: 08' e92 335i
Join Date: Jan 2008
Location: Taipei

iTrader: (0)

BT Scan Tool Found A LOT of fault codes!!! Am I in a serious trouble?

I ran a short test with BT Scan Tool and found 17 errors codes... and i also found a lot of (shadow) fault codes in "Engine - N54 Fault Codes", "Engine - N54 Shadow Fault Codes", Transmission Fault Codes", "Car Access System Fault Codes", "Airbag Fault Codes", "Instrument Cluster Fault Codes" and "Steering Shadow Fault Codes"... Can anyone help me to intepreter these codes? am i in a very serious trouble?

P.S. I have Catless DPs, DCI and a piggyback installed...(I have O2 sim too)

__________________________________________________ ______________
____________________short test result___________________________
Short Test
Engine - N54
Current Fault Codes
________________________________________
29DC
29DC Cylinder injection switch-off
Error will cause a warning light
Error is not currently present
Test conditions have not been completed

________________________________________
2C73
2C73 Lambda probe behind catalytic converter, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
2C74
2C74 Lambda probe behind catalytic converter 2, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
2AAF
2AAF Fuel pump, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
2D25
2D25 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
2A96
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
3100
3100 boost-pressure control, deactivation
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
Fuel pump
No fault codes
________________________________________
Longitudinal mgmt
No fault codes
________________________________________
Power steering
No fault codes
________________________________________
Transmission
Current Fault Codes
________________________________________
51A6
Error engine signal
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Signal or value below threshold

________________________________________
Stability control
Current Fault Codes
________________________________________
5DA3
Yaw rate sensor: DRS sends signal DrsPSIP2=INITstatus error (DRS-Typ MM 3.x).
Error will cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
5D93
Valve relay: Medium or high-resistance short circuit of voltage supply FR or valve after ground registered through start-up test.
Error will cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
5E1A
DSC-ECU: ECU-internal: Serial-Peripheral-Interface (SPI): Transmission failure multi IC.
Error will cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
Transfer case
No fault codes
________________________________________
Air conditioner
No fault codes
________________________________________
Light control
No fault codes
________________________________________
Car Access System
Current Fault Codes
________________________________________
A0B5
Signal identification peed error
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

________________________________________
Junction box
No fault codes
________________________________________
Instrument cluster
Current Fault Codes
________________________________________
A559
Clamp 30g_f cutoff
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
Rain / light sensor
No fault codes
________________________________________
Telematic
No fault codes
________________________________________
Airbags
Current Fault Codes
________________________________________
93FB
SBR - function - Velocity signal missing
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Timeout

________________________________________
Roof control
No fault codes
________________________________________
Seat module - driver
No fault codes
________________________________________
Radio
No fault codes
________________________________________
Radio gateway
No fault codes
________________________________________
Steering
No fault codes
________________________________________
Convertible top
No fault codes
________________________________________
Trailer
No fault codes
________________________________________
Park distance
No fault codes
________________________________________
Central control - low
No fault codes
________________________________________



















__________________________________________________ _______________
__________________________________________________ _______________
Module Identification: MSD80/MSD81 Engine module for N54 (Fault Codes)
________________________________________
Hardware Number XXXXX
Hardware Version Number 00
Coding Index 17
Diagnostic Index 0000
System Name XXXXX
Date Of ECU-Manufacturing 20080327
System Supplier Siemens
Message Catalogue Version 0.0.0
Software Version 0.0.0

MSD80/MSD81 Engine module for N54
Current Fault Codes
________________________________________
29DC:
29DC Cylinder injection switch-off
Error will cause a warning light
Error is not currently present
Test conditions have not been completed

Event 1
Odometer 6824kms 4240miles
Engine temperature 99.00 C
air mass calculated 450.35 mg/stk
Engine speed 1,856.00 rpm
fuel tank filling level 0.00 l


________________________________________
2C73:
2C73 Lambda probe behind catalytic converter, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10808kms 6715miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s

Event 2
Odometer 11368kms 7063miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s

Event 3
Odometer 11592kms 7202miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s


________________________________________
2C74:
2C74 Lambda probe behind catalytic converter 2, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10808kms 6715miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s

Event 2
Odometer 11368kms 7063miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s

Event 3
Odometer 11592kms 7202miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s


________________________________________
2AAF:
2AAF Fuel pump, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10880kms 6760miles
fuel pressure before mass control valve 5,264.27 hPa
Engine speed 2,592.00 rpm
voltage Kl. 87 13.91 V
injected mass of fuel 0.00 l/h

Event 2
Odometer 11176kms 6944miles
fuel pressure before mass control valve 4,924.64 hPa
Engine speed 5,056.00 rpm
voltage Kl. 87 13.91 V
injected mass of fuel 0.00 l/h


________________________________________
2D25:
2D25 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption


________________________________________
2A96:
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 11192kms 6954miles
Engine speed 6,752.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.71 V

Event 2
Odometer 11192kms 6954miles
Engine speed 6,912.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.61 V

Event 3
Odometer 11256kms 6994miles
Engine speed 6,816.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.81 V


________________________________________
3100:
3100 boost-pressure control, deactivation
Error will not cause a warning light
Error is not currently present
Test conditions have been completed


________________________________________




Module Identification: MSD80/MSD81 Engine module for N54 (Shadow Fault Codes)
________________________________________
Hardware Number 7586933
Hardware Version Number 00
Coding Index 17
Diagnostic Index 0000
System Name 4131
Date Of ECU-Manufacturing 20080327
System Supplier Siemens
Message Catalogue Version 0.0.0
Software Version 0.0.0

MSD80/MSD81 Engine module for N54
Current Shadow Fault Codes
________________________________________
2DC5:
2DC5 Torque requirement via CAN controller area network, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed

Event 1
Odometer 6768kms 4205miles
Engine speed 1,184.00 rpm
torque interference via CAN 128.00 -
voltage Kl. 87 11.68 V
status motor control 2.00 0-n

Event 2
Odometer 6768kms 4205miles
Engine speed 1,056.00 rpm
torque interference via CAN 128.00 -
voltage Kl. 87 11.48 V
status motor control 2.00 0-n

Event 3
Odometer 12080kms 7506miles
Engine speed 928.00 rpm
torque interference via CAN 128.00 -
voltage Kl. 87 11.58 V
status motor control 2.00 0-n


________________________________________
29DC:
29DC Cylinder injection switch-off
Error will cause a warning light
Error is not currently present
Test conditions have not been completed

Event 1
Odometer 6824kms 4240miles
Engine temperature 99.00 C
air mass calculated 450.35 mg/stk
Engine speed 1,856.00 rpm
fuel tank filling level 0.00 l


________________________________________
2C73:
2C73 Lambda probe behind catalytic converter, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10808kms 6715miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s

Event 2
Odometer 11368kms 7063miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s

Event 3
Odometer 11592kms 7202miles
exhaust fume temperature behind catalytic converter bank 1 0.00 C
resistor Lambda probe behind catalytic converter bank 1 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 1 1.11 V
time since start end 0.00 s


________________________________________
2C74:
2C74 Lambda probe behind catalytic converter 2, signal
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10808kms 6715miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s

Event 2
Odometer 11368kms 7063miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s

Event 3
Odometer 11592kms 7202miles
exhaust fume temperature behind catalytic converter bank 2 0.00 C
resistor Lambda probe behind catalytic converter bank 2 65,280.00 ohm
voltage Lambda probe behind catalytic converter bank 2 1.11 V
time since start end 0.00 s


________________________________________
2AAF:
2AAF Fuel pump, plausibility
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 10880kms 6760miles
fuel pressure before mass control valve 5,264.27 hPa
Engine speed 2,592.00 rpm
voltage Kl. 87 13.91 V
injected mass of fuel 0.00 l/h

Event 2
Odometer 11176kms 6944miles
fuel pressure before mass control valve 4,924.64 hPa
Engine speed 5,056.00 rpm
voltage Kl. 87 13.91 V
injected mass of fuel 0.00 l/h


________________________________________
2D25:
2D25 manipulation cover, maximum air mass
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption


________________________________________
2A96:
2A96 Crankshaft sensor, tooth failure
Error will cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption

Event 1
Odometer 11192kms 6954miles
Engine speed 6,752.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.71 V

Event 2
Odometer 11192kms 6954miles
Engine speed 6,912.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.61 V

Event 3
Odometer 11256kms 6994miles
Engine speed 6,816.00 rpm
motor status 3.00 0-n
status motor control 2.00 0-n
voltage Kl. 87 13.81 V


________________________________________
3100:
3100 boost-pressure control, deactivation
Error will not cause a warning light
Error is not currently present
Test conditions have been completed


________________________________________




Transmission Current Fault Codes
________________________________________
51A6:
Error engine signal
Error will not cause a warning light
Error is not currently present
Test conditions have not been completed
Signal or value below threshold



Car Access System 3
Current Fault Codes
________________________________________
A0B5:
Signal identification peed error
Error will not cause a warning light
Error is not currently present
Test conditions have been completed
Short circuit or signal interruption




Current Fault Codes
________________________________________
A559:
Clamp 30g_f cutoff
Error will not cause a warning light
Error is not currently present
Test conditions have been completed





instrument cluster fault codes
Multi-restraint system
Current Fault Codes
________________________________________
93FB:
SBR - function - Velocity signal missing
Error will not cause a warning light
Error is not currently present
Test conditions have not been completed
Timeout




Steering Shadow Fault Codes
Active front steering for E90
Current Shadow Fault Codes
________________________________________
7015:

Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
7017:

Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
703D:

Error will not cause a warning light
Error is not currently present
Test conditions have been completed

________________________________________
7119:

Error will not cause a warning light
Error is not currently present
Test conditions have been completed