new d two weeks ago... now JBD - BMW 3-Series (E90 E92) Forum

torque · 11-01-2011, 02:52 PM

So I just got my new 2011 335d sport about two weeks ago and I have loved every minute of it. I've got about 750 miles on her and later this week I am getting the windows tinted.

So I just got my JBD tune today and am about to install it. The only thing: I don't have a PC (MacBook Pro here) so I can't read the codes or change the settings.

I don't really want to change the settings but I am excited to see how much different the car is with the new oomph.

BTW OT: I got a ride in my friends 458 this weekend. Amazing... and got to drive a Phantom coupe. My buddy loves my diesel though... he's also got an M5 and two 993 turbos.

Ron1n · 11-01-2011, 03:06 PM

There's nothing you're going to do to change the settings with the OBDII, most likely. That's for viewing/clearing codes. Get a netbook so that you can, though. You'll appreciate it.

BMW1983 · 11-01-2011, 03:25 PM

Run Windows on your mac like I do when needed for this.....no big deal....use Boot Camp to do it...

torque · 11-01-2011, 04:13 PM

Just installed the JBD and started it up and Reduced Engine Power.

I don't have a PC but I'm trying to get a friend over here who has one so I can see what the fuck is going on. This pretty much sucks... not gonna lie. If it doesn't work and then I uninstall it and it is still throwing codes I am really gonna be pissed because of how excited I was earlier today.

I will keep you posted...

any help/information would be appreciated.

Ron1n · 11-01-2011, 04:52 PM

It's not gonna throw codes when you uninstall it. What's the setting showing on the JBD now (approximately how far is it from all the way to the right)?

rakimb17 · 11-01-2011, 05:53 PM

Quote:

Originally Posted by BMW1983

Run Windows on your mac like I do when needed for this.....no big deal....use Boot Camp to do it...

x2

cssnms · 11-01-2011, 05:55 PM

Shouldn't cause your car to go into lump mode at the default setting. Unscrew the cover on the jbd and make sure it is set at a little over half way.

torque · 11-01-2011, 06:12 PM

So I went back outside and just removed the module and it is now sitting on my living room table. The meter inside reads just past the half way mark (about 60%). As I started the car back up everything was fine except for the SES light but no codes on the dash or iDrive.

I emailed Burger a few questions and there responses were incredibly prompt. So kudos to Burger Tuning. I didn't get a chance to snap a picture as to if everything was installed correctly but I am mechanically inclined and it is basically a plug&play so I think it's just a communication error.

Hoping to get this Boot Camp but it'll take me a minute since I am not a huge computer nerd and just surf the net and basic shit... so bare with me folks.

Ron1n · 11-01-2011, 06:46 PM

Quote:

Originally Posted by torque

So I went back outside and just removed the module and it is now sitting on my living room table. The meter inside reads just past the half way mark (about 60%). As I started the car back up everything was fine except for the SES light but no codes on the dash or iDrive.

I emailed Burger a few questions and there responses were incredibly prompt. So kudos to Burger Tuning. I didn't get a chance to snap a picture as to if everything was installed correctly but I am mechanically inclined and it is basically a plug&play so I think it's just a communication error.

Hoping to get this Boot Camp but it'll take me a minute since I am not a huge computer nerd and just surf the net and basic shit... so bare with me folks.

Yeah, Terry is awesome, and very prompt...always willing to help.

You might want to consider just putting more miles on your car for now (get it past the break-in period) before tossing the JBD back on.

cssnms · 11-01-2011, 06:48 PM

Did you make sure to lock the car and let the ecu go to sleep before installing? If not it will cause codes.

Since you car went into limp mode and ses light you will need to clear codes with bt cable. Even if light is not on car stores codes in memory until cleared.

Ron1n · 11-01-2011, 06:54 PM

Quote:

Originally Posted by cssnms

Did you make sure to lock the car and let the ecu go to sleep before installing? If not it will cause codes.

Since you car went into limp mode and ses light you will need to clear codes with bt cable. Even if light is not on car stores codes in memory until cleared.

Given the amount of time it takes to install, the car should have been asleep already. I only do that, btw, when I'm setting up to clear codes, not swap out the tune (with 3 tunes to play with, it happens more often than you think). :P

Kaylin032 · 11-01-2011, 11:17 PM

I got a 2011 335d a couple months ago, and put a JBD on it after about 4,000 miles. I maxed out the setting and and the car drives like a monster and fortunately I haven't experienced any error codes.

I hope you get it working. The 335d isn't bad as-is, but it's hard to describe the white-knuckle fun/terror you get at 2,000 rpm to your friends with an "i" instead of a "d" on the badges of their cars. They need to feel it so they can be jealous.

I just wish the suspension was firmer. I hit the bumpstops on speed bumps that my M3 would laugh at.

KP

torque · 11-02-2011, 05:41 PM

So I ended up just clearing the P0193 code that caused the SES light to be on after I uninstalled the module.

cssnms: I locked her and had both keys inside my apartment about 100ft. away for well over 10 minutes. I just wish I had this chip to enjoy today since my right ear is completed stopped up and it has been hell at work all day.

Terry and I emailed back and forth yesterday and I ended up just taking it off for now.
I spoke with two friends of mine who are BMW mechanics and they are just going to help me out when I take it in next.

Thanks for all the help and I will get this figured out sooner rather than later... I still have to tint her and get a permanent tag for ***s sake.

duramax · 11-02-2011, 07:18 PM

I am kind of like you, I got my D a month and a half ago and the JBD w/CAN tool is on its way. I have 2,100 miles on now and had the windows tinted the first week. I love the car. Can someone explain or point me in the right direction: My understanding is the CAN tool can only tell you if you have a fault code store in the ECU and can clear it, without the need for a PC/laptop. I don't understand what the PC is being used for?? Is there an application on the PC that reads the codes? Is this a different tool than the CAN Tool used to do this?

Thanks in advance

Ron1n · 11-02-2011, 07:35 PM

Quote:

Originally Posted by duramax

I am kind of like you, I got my D a month and a half ago and the JBD w/CAN tool is on its way. I have 2,100 miles on now and had the windows tinted the first week. I love the car. Can someone explain or point me in the right direction: My understanding is the CAN tool can only tell you if you have a fault code store in the ECU and can clear it, without the need for a PC/laptop. I don't understand what the PC is being used for?? Is there an application on the PC that reads the codes? Is this a different tool than the CAN Tool used to do this?

Thanks in advance

Yup...it's the BT software itself. It provides a lot more information for you.

To get an idea, check out my YT video:

duramax · 11-02-2011, 08:04 PM

Very cool. So a couple more dumb questions. Where do you get the BT Software from and is the CAN tool Cable the one you are using or is that something different?

M-igs-3 · 11-02-2011, 10:03 PM

Quote:

Originally Posted by torque

So I went back outside and just removed the module and it is now sitting on my living room table. The meter inside reads just past the half way mark (about 60%). As I started the car back up everything was fine except for the SES light but no codes on the dash or iDrive.

I emailed Burger a few questions and there responses were incredibly prompt. So kudos to Burger Tuning. I didn't get a chance to snap a picture as to if everything was installed correctly but I am mechanically inclined and it is basically a plug&play so I think it's just a communication error.

Hoping to get this Boot Camp but it'll take me a minute since I am not a huge computer nerd and just surf the net and basic shit... so bare with me folks.

I'm curious to see how this turns out for you... hopefully it turns out well!

.. just ordered my JBD and CAN tool tonight as well!

EYE4SPEED · 11-03-2011, 11:29 AM

My friend only gets the SES light when he floors the car off the line. Otherwise from a roll, no problems. Setting is around 75%.

duramax · 11-03-2011, 04:16 PM

I got the JBD in the mail today (they didn't send me the CAN tool). I contacted them and they responded within 10 minutes and are working it out, some sort of order mix up. I installed it, the only thing I was worried about was the not breaking the white insert. I got it out no problems. The last driver side allen bolt was easy getting out, not so easy getting back in. Took her for a drive and I am pretty impressed. Didn't have much time to have fun because of work, but it gets up and goes, no codes on default.

duramax · 11-03-2011, 04:40 PM

I would like to add Burger shipped the CAN tool an hour after emailing them. Good work.

szhark · 11-04-2011, 09:14 PM

'11 335d.. 5300 miles.. JBD @ 75%.. anything higher throws limp mode.. Car is unreal to drive... start lower and inch up..

duramax · 11-05-2011, 10:21 PM

got the CAN tool today. I assume the ignition on to clear/read codes, engine off?

11-01-2011, 02:52 PM	#1
torque New Member Drives: 2011 335d Join Date: Oct 2011 Location: USA Posts: 16 iTrader: (0)	new d two weeks ago... now JBD So I just got my new 2011 335d sport about two weeks ago and I have loved every minute of it. I've got about 750 miles on her and later this week I am getting the windows tinted. So I just got my JBD tune today and am about to install it. The only thing: I don't have a PC (MacBook Pro here) so I can't read the codes or change the settings. I don't really want to change the settings but I am excited to see how much different the car is with the new oomph. BTW OT: I got a ride in my friends 458 this weekend. Amazing... and got to drive a Phantom coupe. My buddy loves my diesel though... he's also got an M5 and two 993 turbos.
	Tweet

11-01-2011, 03:06 PM	#2
Ron1n Speed Demon Drives: '10 335d E90 Join Date: Oct 2009 Location: The 858 Posts: 3,242 iTrader: (4) Garage List 2010 335d [5.00]	There's nothing you're going to do to change the settings with the OBDII, most likely. That's for viewing/clearing codes. Get a netbook so that you can, though. You'll appreciate it. __________________

11-01-2011, 04:52 PM	#5
Ron1n Speed Demon Drives: '10 335d E90 Join Date: Oct 2009 Location: The 858 Posts: 3,242 iTrader: (4) Garage List 2010 335d [5.00]	It's not gonna throw codes when you uninstall it. What's the setting showing on the JBD now (approximately how far is it from all the way to the right)? __________________

11-01-2011, 11:17 PM	#12
Kaylin032 Private Drives: E93 M3 and 335d Join Date: Oct 2011 Location: Dallas TX Posts: 79 iTrader: (0) Garage List 2011 BMW 335d [3.25] 2011 BMW M3 Convert ... [4.50]	No probs I got a 2011 335d a couple months ago, and put a JBD on it after about 4,000 miles. I maxed out the setting and and the car drives like a monster and fortunately I haven't experienced any error codes. I hope you get it working. The 335d isn't bad as-is, but it's hard to describe the white-knuckle fun/terror you get at 2,000 rpm to your friends with an "i" instead of a "d" on the badges of their cars. They need to feel it so they can be jealous. I just wish the suspension was firmer. I hit the bumpstops on speed bumps that my M3 would laugh at. KP

11-03-2011, 11:29 AM	#18
EYE4SPEED Ex-Quattro Driver Drives: E90 335d M-Sport LCI Join Date: Apr 2010 Location: West Coast... of Michigan Posts: 1,984 iTrader: (21)	My friend only gets the SES light when he floors the car off the line. Otherwise from a roll, no problems. Setting is around 75%. __________________ FS: HRE Center Caps http://www.e90post.com/forums/showth...post13972317l] FS: OEM Kidneys http://www.e90post.com/forums/showthread.php?t=783447

11-01-2011, 03:25 PM	#3
BMW1983 Private First Class Drives: 2011 335d Join Date: Nov 2007 Location: Houston, Texas Posts: 132 iTrader: (0)	Run Windows on your mac like I do when needed for this.....no big deal....use Boot Camp to do it...

11-01-2011, 04:13 PM	#4
torque New Member Drives: 2011 335d Join Date: Oct 2011 Location: USA Posts: 16 iTrader: (0)	Just installed the JBD and started it up and Reduced Engine Power. I don't have a PC but I'm trying to get a friend over here who has one so I can see what the fuck is going on. This pretty much sucks... not gonna lie. If it doesn't work and then I uninstall it and it is still throwing codes I am really gonna be pissed because of how excited I was earlier today. I will keep you posted... any help/information would be appreciated.

11-01-2011, 05:55 PM	#7
cssnms Brigadier General Drives: 2011 BMW 335d Join Date: Sep 2010 Location: Murland Posts: 3,094 iTrader: (4)	Shouldn't cause your car to go into lump mode at the default setting. Unscrew the cover on the jbd and make sure it is set at a little over half way.

11-01-2011, 06:12 PM	#8
torque New Member Drives: 2011 335d Join Date: Oct 2011 Location: USA Posts: 16 iTrader: (0)	So I went back outside and just removed the module and it is now sitting on my living room table. The meter inside reads just past the half way mark (about 60%). As I started the car back up everything was fine except for the SES light but no codes on the dash or iDrive. I emailed Burger a few questions and there responses were incredibly prompt. So kudos to Burger Tuning. I didn't get a chance to snap a picture as to if everything was installed correctly but I am mechanically inclined and it is basically a plug&play so I think it's just a communication error. Hoping to get this Boot Camp but it'll take me a minute since I am not a huge computer nerd and just surf the net and basic shit... so bare with me folks.

11-01-2011, 06:48 PM	#10
cssnms Brigadier General Drives: 2011 BMW 335d Join Date: Sep 2010 Location: Murland Posts: 3,094 iTrader: (4)	Did you make sure to lock the car and let the ecu go to sleep before installing? If not it will cause codes. Since you car went into limp mode and ses light you will need to clear codes with bt cable. Even if light is not on car stores codes in memory until cleared.

11-02-2011, 05:41 PM	#13
torque New Member Drives: 2011 335d Join Date: Oct 2011 Location: USA Posts: 16 iTrader: (0)	So I ended up just clearing the P0193 code that caused the SES light to be on after I uninstalled the module. cssnms: I locked her and had both keys inside my apartment about 100ft. away for well over 10 minutes. I just wish I had this chip to enjoy today since my right ear is completed stopped up and it has been hell at work all day. Terry and I emailed back and forth yesterday and I ended up just taking it off for now. I spoke with two friends of mine who are BMW mechanics and they are just going to help me out when I take it in next. Thanks for all the help and I will get this figured out sooner rather than later... I still have to tint her and get a permanent tag for ***s sake.

11-02-2011, 07:18 PM	#14
duramax Enlisted Member Drives: 2011 335D Join Date: Sep 2011 Location: Kansas City, MO Posts: 38 iTrader: (0)	I am kind of like you, I got my D a month and a half ago and the JBD w/CAN tool is on its way. I have 2,100 miles on now and had the windows tinted the first week. I love the car. Can someone explain or point me in the right direction: My understanding is the CAN tool can only tell you if you have a fault code store in the ECU and can clear it, without the need for a PC/laptop. I don't understand what the PC is being used for?? Is there an application on the PC that reads the codes? Is this a different tool than the CAN Tool used to do this? Thanks in advance

11-02-2011, 08:04 PM	#16
duramax Enlisted Member Drives: 2011 335D Join Date: Sep 2011 Location: Kansas City, MO Posts: 38 iTrader: (0)	Very cool. So a couple more dumb questions. Where do you get the BT Software from and is the CAN tool Cable the one you are using or is that something different?

11-03-2011, 04:16 PM	#19
duramax Enlisted Member Drives: 2011 335D Join Date: Sep 2011 Location: Kansas City, MO Posts: 38 iTrader: (0)	I got the JBD in the mail today (they didn't send me the CAN tool). I contacted them and they responded within 10 minutes and are working it out, some sort of order mix up. I installed it, the only thing I was worried about was the not breaking the white insert. I got it out no problems. The last driver side allen bolt was easy getting out, not so easy getting back in. Took her for a drive and I am pretty impressed. Didn't have much time to have fun because of work, but it gets up and goes, no codes on default.

11-03-2011, 04:40 PM	#20
duramax Enlisted Member Drives: 2011 335D Join Date: Sep 2011 Location: Kansas City, MO Posts: 38 iTrader: (0)	I would like to add Burger shipped the CAN tool an hour after emailing them. Good work.

11-04-2011, 09:14 PM	#21
szhark New Member Drives: 335D Join Date: Aug 2011 Location: Los Angeles Posts: 6 iTrader: (0)	'11 335d.. 5300 miles.. JBD @ 75%.. anything higher throws limp mode.. Car is unreal to drive... start lower and inch up..

11-05-2011, 10:21 PM	#22
duramax Enlisted Member Drives: 2011 335D Join Date: Sep 2011 Location: Kansas City, MO Posts: 38 iTrader: (0)	got the CAN tool today. I assume the ignition on to clear/read codes, engine off?

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search