Ugh. JB+ problem. - BMW 3-Series (E90 E92) Forum

Turb0Surge · 06-07-2012, 08:33 AM

So... I picked up a used jb+ for cheap yesterday online. Didn't wana spend the money for a jb3/4 and would have been more than satisfied with the 40 hp gain the jb+ offers.

So I install the jb+ (simple enough) and when I reconnect the battery and start the car it automatically starts shuddering and rpms start jumping. When you put it into drive it starts jerking horribly and after a few moments CEL comes on and it goes into limp mode.

The car does not have these problems when jb+ is disconnected.

Help anyone?

E90Company · 06-07-2012, 08:35 AM

Are you sure it's connected to the correct sensor?? I know my friend said that two connectors looked very similar when he was installing his.

PS Post in N54 section

Turb0Surge · 06-07-2012, 08:45 AM

Quote:

Originally Posted by E90Company

Are you sure it's connected to the correct sensor?? I know my friend said that two connectors looked very similar when he was installing his.

PS Post in N54 section

Yeah it's the correct one.

BAL278 · 06-07-2012, 08:50 AM

Yeah.. I would also check what it is set to, but more than likely it is not connected properly, you don't need to disconnect the battery, just make sure the ECU goes to sleep

Sara504 · 06-07-2012, 08:53 AM

Uh oh...

Turb0Surge · 06-07-2012, 08:58 AM

Yeah, it was originally set to 100%. Now it's at the minimum setting.

86rexer · 06-07-2012, 10:09 AM

Quote:

Originally Posted by BAL278

Yeah.. I would also check what it is set to, but more than likely it is not connected properly, you don't need to disconnect the battery, just make sure the ECU goes to sleep

Exactly what he said

. open the hood prep the area and put your keys inside the house, and wait for at least 15min...or disconnect the battery for a definite power off.

Turb0Surge · 06-07-2012, 11:21 AM

Quote:

Originally Posted by 86rexer

Exactly what he said

. open the hood prep the area and put your keys inside the house, and wait for at least 15min...or disconnect the battery for a definite power off.

No its definately plugged in correctly. In fact, I took it off/ on 4 times. (each time I dilaed down the boost) now I'm at minimum boost and it still does it. Battery was disconnected when I put it on each time.

Lulz_M3 · 06-07-2012, 11:55 AM

You are either installing it wrong or you got sold a bricked JB+. Are you following the instructions from Burgers website? You might be plugging it into the map sensor in the intake manifold instead of the one on intake pipe before the throttle body.

Turb0Surge · 06-07-2012, 11:56 AM

Quote:

Originally Posted by Lulz_M3

You are either installing it wrong or you got sold a bricked JB+. Are you following the instructions from Burgers website? You might be plugging it into the map sensor in the intake manifold instead of the one on intake pipe before the throttle body.

Yeah, followed all instructions. And sadly, I have been plugging it in correctly so I think it is a bad chip. But I bought it on ebay so hopefully I'll get my money back.

quasitime · 06-07-2012, 12:14 PM

You may want to check the connections on the JB+. The wires have a tendency to get pulled lose out of their sockets from the removal process. It is pretty noticeable if you shine a light inside the connector, and look to see that all the metal contacts are lined up correctly. When this happened to me, one of the contacts was pulled back.

benzy89 · 06-07-2012, 12:20 PM

Poor choice making the eBay purchase -- Sounds like you either got screwed with a fake/broken JB+ or when you're putting the tune on, it's inducing misfires since you're running the car at a higher performance settings. I'm dealing with this right now -- My car was running at COBB Stg 1, but now that I've bumped the tune up to Stg 2 the car is misfiring (replacing the plugs/coils this weekend).

Turb0Surge · 06-07-2012, 02:18 PM

***UPDATE***

I just went out to lunch and before I went i took the jb+ out. (using proper procedure, of course) Drove to in-n-out and CEL disappeared, and car started pulling normally and no sputter. Basically running how it's supposed to.

When I was installing it I disconnected the battery and then installed it as opposed to waiting 15min with the hood open for the ecu to fall asleep. (Jb website says either way is fine) maybe that's my problem?

benzy89 · 06-07-2012, 03:03 PM

I can't answer 100%, but if you didn't follow the install correctly that might be a reason why it didn't work out well.

tanginaglaz · 06-07-2012, 11:45 PM

Take pictures of how you installed it. Just want to confirm that it was installed properly. I would also suggest to pull the codes.

06-07-2012, 08:33 AM	#1
Turb0Surge Major Drives: BLACK e90 335i Join Date: May 2012 Location: Lincoln, CA Posts: 1,283 iTrader: (0)	Ugh. JB+ problem. So... I picked up a used jb+ for cheap yesterday online. Didn't wana spend the money for a jb3/4 and would have been more than satisfied with the 40 hp gain the jb+ offers. So I install the jb+ (simple enough) and when I reconnect the battery and start the car it automatically starts shuddering and rpms start jumping. When you put it into drive it starts jerking horribly and after a few moments CEL comes on and it goes into limp mode. The car does not have these problems when jb+ is disconnected. Help anyone?
	Tweet

06-07-2012, 08:35 AM	#2
E90Company Major General Drives: 335i Join Date: Mar 2012 Location: SFL Posts: 5,542 iTrader: (2)	Are you sure it's connected to the correct sensor?? I know my friend said that two connectors looked very similar when he was installing his. PS Post in N54 section __________________ FBO N54 6AT

06-07-2012, 08:50 AM	#4
BAL278 Captain Drives: E92 335xi JB Join Date: Jun 2011 Location: North NJ (FLakes) Posts: 708 iTrader: (0)	Yeah.. I would also check what it is set to, but more than likely it is not connected properly, you don't need to disconnect the battery, just make sure the ECU goes to sleep __________________ 2008 335xi Jet Black//Coral Red Procede V5//AMS FMIC//KW V1//M3 Sways & Sub Bushings// Alpina AT flash

06-07-2012, 08:53 AM	#5
Sara504 ///Miss E92 Drives: 2013 335is Join Date: Aug 2007 Location: Newport Beach, CA Posts: 17,086 iTrader: (5)	Uh oh... __________________ 2013 335is-Current 2011 335i -Sold 4/13 2006 325i-Sold 7/11

06-07-2012, 11:45 PM	#15
tanginaglaz Captain Drives: 2007 e92 335i Join Date: Apr 2011 Location: SO CAL Posts: 758 iTrader: (10) Garage List 2007 BMW E92 335i [5.00]	Take pictures of how you installed it. Just want to confirm that it was installed properly. I would also suggest to pull the codes. __________________

06-07-2012, 08:58 AM	#6
Turb0Surge Major Drives: BLACK e90 335i Join Date: May 2012 Location: Lincoln, CA Posts: 1,283 iTrader: (0)	Yeah, it was originally set to 100%. Now it's at the minimum setting.

06-07-2012, 11:55 AM	#9
Lulz_M3 Banned Drives: AW 335i 6MT Join Date: Oct 2011 Location: Jax, Fl Posts: 1,031 iTrader: (0)	You are either installing it wrong or you got sold a bricked JB+. Are you following the instructions from Burgers website? You might be plugging it into the map sensor in the intake manifold instead of the one on intake pipe before the throttle body.

06-07-2012, 12:14 PM	#11
quasitime Private Drives: 2007 335i 6MT Join Date: Aug 2008 Location: Los Angeles Posts: 84 iTrader: (1)	You may want to check the connections on the JB+. The wires have a tendency to get pulled lose out of their sockets from the removal process. It is pretty noticeable if you shine a light inside the connector, and look to see that all the metal contacts are lined up correctly. When this happened to me, one of the contacts was pulled back.

06-07-2012, 12:20 PM	#12
benzy89 Banned Drives: '08 E90 335i Join Date: Jan 2012 Location: Northern NJ Posts: 2,402 iTrader: (3) Garage List 2008 BMW 335i [3.75]	Poor choice making the eBay purchase -- Sounds like you either got screwed with a fake/broken JB+ or when you're putting the tune on, it's inducing misfires since you're running the car at a higher performance settings. I'm dealing with this right now -- My car was running at COBB Stg 1, but now that I've bumped the tune up to Stg 2 the car is misfiring (replacing the plugs/coils this weekend).

06-07-2012, 02:18 PM	#13
Turb0Surge Major Drives: BLACK e90 335i Join Date: May 2012 Location: Lincoln, CA Posts: 1,283 iTrader: (0)	*UPDATE* I just went out to lunch and before I went i took the jb+ out. (using proper procedure, of course) Drove to in-n-out and CEL disappeared, and car started pulling normally and no sputter. Basically running how it's supposed to. When I was installing it I disconnected the battery and then installed it as opposed to waiting 15min with the hood open for the ecu to fall asleep. (Jb website says either way is fine) maybe that's my problem?

06-07-2012, 03:03 PM	#14
benzy89 Banned Drives: '08 E90 335i Join Date: Jan 2012 Location: Northern NJ Posts: 2,402 iTrader: (3) Garage List 2008 BMW 335i [3.75]	I can't answer 100%, but if you didn't follow the install correctly that might be a reason why it didn't work out well.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search