E90Post
 


Scorpp Design
 
BMW 3-Series (E90 E92) Forum > BMW E90/E92/E93 3-series General Forums > Regional Forums > UK > UK Technical Forum > mouldy indicator repeaters - how to remove ?



Reply
 
Thread Tools Search this Thread
      06-15-2012, 03:50 AM   #1
Jules59
First Lieutenant
 
Jules59's Avatar
 
Drives: E91
Join Date: Nov 2010
Location: UK. Warwickshire

Posts: 344
iTrader: (0)

mouldy indicator repeaters - how to remove ?

My indicator repeaters on the front wing are going mouldy on the inside after 3 years.



How are they removed so I can clean up the inside ?
Do you have to remove the wheel arch liner and get at them from their rear or do they just pull straight out ?
__________________
Jules
Jules59 is offline   United Kingdom
0
Reply With Quote
      06-15-2012, 04:06 AM   #2
nush e91
New Member
 
Drives: E91
Join Date: Oct 2011
Location: Newcastle

Posts: 28
iTrader: (1)

Slide the unit towards the back of the car then pull out from the front of the unit.
nush e91 is offline  
0
Reply With Quote
      06-15-2012, 04:06 AM   #3
Hotcoupe
Major General
 
Hotcoupe's Avatar
 
Drives: Don't know yet!
Join Date: Jul 2007
Location: UK

Posts: 6,095
iTrader: (2)

Garage List
Quote:
Originally Posted by Jules59 View Post
My indicator repeaters on the front wing are going mouldy on the inside after 3 years.

How are they removed so I can clean up the inside ?
Do you have to remove the wheel arch liner and get at them from their rear or do they just pull straight out ?
Push the repeater to the left or right (can't remember which way) and pull the back of the repeater out of the hole.

The repeater is then connected to the main loom by a small connector block.

The arch liner does not need to be removed.

Note: The repeater unit is sealed,so can't be seperated to clean the inside of the lens.
You could try popping the unit in the oven for 15 mins (No, I'm not kidding!) on a low heat to soften the glue to seperate the two parts.
Reseal with silicone.

Or buy new ones (probably far easier )
Hotcoupe is offline   United Kingdom
0
Reply With Quote
      06-15-2012, 04:12 AM   #4
AlwynMike
Captain
 
Drives: E91 335d.
Join Date: Sep 2010
Location: Shropshire, UK

Posts: 889
iTrader: (1)

Dead easy job!

First waggle the unit clockwise/anticlockwise as you look at it - just to break any seal that will have formed by the 3 years of accumulated road crud.

With the unit now able to move slightly (there won't be much), grip the unit and push (I think) towards the rear of the car. This will compress the spring clip - you'll need a good grip! As the unit slides rearwards, you willbe able to angle the front of the light unit out from the wing as this is just a hook. Remove the unit and disconnect the plug.

You will struggle to get anything inside the unit when the bulb is out, but at least you'll be able to wash it with something.

Mike
AlwynMike is offline   United Kingdom
0
Reply With Quote
      06-15-2012, 01:19 PM   #5
acerboo
Brigadier General
 
Drives: e92 335d lci
Join Date: Jul 2008
Location: kent

Posts: 3,482
iTrader: (2)

they all seem to do this cheap rubbish! make sure the loom doest drop insude the wing when you take the light out
acerboo is offline   England
0
Reply With Quote
      06-15-2012, 01:58 PM   #6
B005T3D-G
Class Leading Reprobate
 
B005T3D-G's Avatar
 
Drives: Impreza STi - E92 335i (56)
Join Date: Oct 2011
Location: Mintlaw, Scotland

Posts: 421
iTrader: (0)

Garage List
Once you get the repeater unit out tape the wiring to the wing do it doesn't fall in then soak the repeater unit in hot water with a baby bottle steriliser tablet for 20-30 mins. That'll kill off the bacteria and will come clean with a rinse of fresh water.
__________________
E92 335i | 6 Speed manual | BMS 4xLED Halo Bulbs | JB4 (waiting to be installed) | BMW Performance Gloss Black Grills | BMW Performance Exhaust | Smoked side Repeaters
Aero Front Lip | M3 Lip Spoiler |19" Cades Tyrus 'Gunmetal' with polished lips | Falken FK452 Rubber
........... More to come
B005T3D-G is offline   Scotland
0
Reply With Quote
      06-15-2012, 04:10 PM   #7
Jules59
First Lieutenant
 
Jules59's Avatar
 
Drives: E91
Join Date: Nov 2010
Location: UK. Warwickshire

Posts: 344
iTrader: (0)

cheers guys. I'll give it a go tomorrow.
__________________
Jules
Jules59 is offline   United Kingdom
0
Reply With Quote
      06-16-2012, 07:00 PM   #8
Jules59
First Lieutenant
 
Jules59's Avatar
 
Drives: E91
Join Date: Nov 2010
Location: UK. Warwickshire

Posts: 344
iTrader: (0)

The two plastic parts of the unit are bonded and the mould grows in that joint. I used hot water, washing up liquid , Milton and a tooth brush - managed to get most of the mould out. But the silicone rubber is still stained.

Here is a photo which makes it obvious how the get them off the the car (bulb & holder removed). Wiggle to loosen and then push sideways towards the rear and lift out the front edge - easy.
Attached Images
 
__________________
Jules
Jules59 is offline   United Kingdom
0
Reply With Quote
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 01:04 PM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST