[woodpecka]

I have successfully coded a few features on my e91 2006.

I have a few issues to get access to some value, I don't understand why they are not available in the modules TRC files but present on the car TRC file.


JBBF (2JBBF) ZYCLUS_VOLLEND_KLR_AUS Wiper wipes to End position after turning engine off (not present in my KOMBI TRC file but present in my 221k car TRC file)

KOMBI DIGITAL_KVA Instant MPG (not present in my KOMBI TRC file but present in my 221k car TRC file)

I also don't found the LMA module. Is it supposed to be available on a pre lci?

[woodpecka]

Anybody knows?

[DESI4life10]

ZYCLUS_VOLLEND_KLR_AUS

This is in the JBBF or 2JBBF module (not Kombi).

Try BC_DIGITAL_V in the Kombi module to get the digital speed display.

ER_KEYOUT_AUTOVR
Are your setting set so that the car auto lock the doors when you drive off? This should be on

LMA is a module not used on the e9x cars. I believe it is similar to our FRM or NFRM module

[woodpecka]

I have coded a few parameters with success in the KOMBI, including the V display.

I can't found ZYCLUS_VOLLEND_KLR_AUS in the JBBF (!?)

ER_KEYOUT_AUTOVR is working now!

[dcan]

Originally Posted by DESI4life10

Try BC_DIGITAL_V in the Kombi module to get the digital speed display.

Enabling BC_DIGITAL_V in itself is not enough, if you want to see the real measured speed - in this case, you have to disable BC_DIGITAL_V_KORREKTUR, too. Since speedometers aren't allowed to show a lower speed than the actual speed, and an exact speed measurement is not always possible, all manufacturers correct the measured speed slightly upwards in order to comply with ECE-R 39 regulations:

http://www.unece.org/trans/main/wp29...gs/r039r1e.pdf

Look for the formulae under Annex 3, Section 2. The U.S. regulations must have a similar counterpart, too.

[woodpecka]

I have disable BC_DIGITAL_V_KORREKTUR with success!

I tried to disable BC_V_KORREKTUR thinking that I would get the real analog speed but this one has no effect.

[dcan]

Originally Posted by woodpecka

I have disable BC_DIGITAL_V_KORREKTUR with success!

I tried to disable BC_V_KORREKTUR thinking that I would get the real analog speed but this one has no effect.

That's a different pair of shoes; it configures whether corrected speed values should be used for BC calculations. So, it has an effect, too.

[dcan]

Originally Posted by woodpecka

I can't found ZYCLUS_VOLLEND_KLR_AUS in the JBBF (!?)

That's because you don't have a JunctionBox II, but a JunctionBox I, with an old SW below CI-7.

[vadim77]

what is the 221k file? I can't activate digital-kva function!!! In Kombi ok (active), but no info in cluster)

[toicy4ya]

Originally Posted by woodpecka

ER_KEYOUT_AUTOVR is working now!

How did you get it to work? Did you do in CAS?

Did you also have to mod Komfort_Eject along with it?

[Elliott@DetailAddict]

Originally Posted by toicy4ya

How did you get it to work? Did you do in CAS?

Did you also have to mod Komfort_Eject along with it?

In order for the Unlock on Keyout to work, make sure the car is set to lock itself upon driving.
That has to happen for the unlock to work.

[rentonrider]

Originally Posted by Grant@DetailAddict

In order for the Unlock on Keyout to work, make sure the car is set to lock itself upon driving.
That has to happen for the unlock to work.