E90Post
 


 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > DIY Guides > DIY: Ghetto Tow Hook License Plate Mount $5.00



Reply
 
Thread Tools Search this Thread
      09-25-2012, 04:48 AM   #1
vtsng
Second Lieutenant
vtsng's Avatar
Canada
13
Rep
251
Posts

Drives: Pre LCI E90 325i SGM
Join Date: Jun 2012
Location: GVA (BC) / Seattle (WA)

iTrader: (4)

DIY: Ghetto Tow Hook License Plate Mount $5.00

Not sure if anyone else has done this yet, but I thought I'd share my experience here anyways.

Total cost: $5 (most of the supplies I had sitting around at home)

Metal piece was $2 - home depot
Drywall Anchor ~$1.75 - home depot
Rubber pads were $1 - dollar store

You may notice that some pictures already have some steps completed in advance (trial and error). The steps listed below are in proper order, regardless of what the pictures may communicate.

So here's how its done:

Materials:

- Scrap Metal Piece (this should come flat, not already bent as shown in the pictures)

- Butterfly Drywall Anchor

- Felt pads/ Rubber Pads

- Sandpaper (220 and 320 grit should be sufficient)

- Paint/ Plastidip (if you want to prevent rust)

- Double Sided Tape (3m automotive)





Step 1:

Sand the metal piece to prep for plastidip/ paint. Sand until the surface is clean and smooth, much like the matte blades of the scissors pictured below





Step 2:

Bend a dip slightly larger than the width of the tow hook opening into the metal piece, then drill a hole through the center of the dip:

*The pictures below show an unsanded piece. I would recommend sanding BEFORE bending it as it is much easier to sand across a flat surface



I couldn't find my drills so I just hammered a hole through the metal in a rush to get the plate on asap, hence the bulging edges.





Step 3:

Paint to prevent rust (thin coats)



You might as well paint the back of the license plate as well. This helps to hide the reflection on your bumper.



Step 4:

Stick two felt pads on to the angled sections of the metal piece (approximately 3 inches in length each). This will add a soft barrier between the bare metal piece and your bumper, you'll see what I mean later.



Step 5:

Put the ghetto rig together as pictured below:

The washer may not be necessary





Step 6:

Push the drywall anchor into the tow hook opening. Make sure it is grabbing to the back of the bumper in a HORIZONTAL position so that it is holding on to the tabs on the left and right side of the opening that the tow hook cover would have been clinging on to.

While you tighten the assembly, the anchor will push in to the back left and right sides of the opening. The plate mount will press down on the same spots (however on the outside) preventing the bumper from stretching/ warping.

If the anchor is placed vertically (grabbing the top and bottom of the back side of the bumper), it will pull that section outwards. As there is no downwards pressure stopping the outward movement, it will slowly warp the bumper as you tighten the assembly.



Step 7:

Double-side tape the plate on, remember to test fit first. If you want the plate to be further to one side, you may need to saw the metal piece down on one side to prevent it from sticking out past the side of the license plate (as I had to do).











This is the position before sawing down the metal piece:


Last edited by vtsng; 09-25-2012 at 06:19 AM.
Appreciate 0
      09-25-2012, 02:11 PM   #2
///M3NACE
Banned
///M3NACE's Avatar
79
Rep
3,905
Posts

Drives: E36 M3, E36 Vert , E90 N52
Join Date: Oct 2006
Location: Downers Grove, IL

iTrader: (5)

Nice writeup! I just 3m my whole plate and put it on the side. Yours looks more effective but how did this work at higher speeds?
Appreciate 0
      09-25-2012, 02:54 PM   #3
wdeerfield
A family of bimmers
United_States
419
Rep
4,907
Posts

Drives: '13 f30, '11 f10
Join Date: Jan 2012
Location: Clifton Park, NY

iTrader: (0)

Nice write up and i may consider doing this. but why not just use a bolt that screws into the tow hook opening? You could do some trial and error with length and just use a nut on the front and back of the plate holder for the correct distance out from the bumper. Maybe for version 2.
__________________
2013 EB 335i xdrive | Msport | Coral | DHP | ZPP | ZCW | ZTP | 400M | Coded | MPerformance Bits | M3 Grills | Painted Reflectors | BMS Exhaust Tips | LED Turn Signals
2011 JB 535i xdrive | ZPP | ZSP | ZCW | 6FL | NAV | 331s Square | MPerformance Spoiler | M5 Grills | Painted Reflectors
Appreciate 0
      09-25-2012, 11:16 PM   #4
Slow_335i
Daily Driven!
Slow_335i's Avatar
United_States
103
Rep
2,516
Posts

Drives: BMW 335i
Join Date: Jun 2011
Location: Central Illinois

iTrader: (11)

Garage List
2008 BMW 335I  [3.51]
Nice info

one question what size drywall anchor did you have to use?
__________________
Appreciate 0
      09-26-2012, 06:06 AM   #5
vtsng
Second Lieutenant
vtsng's Avatar
Canada
13
Rep
251
Posts

Drives: Pre LCI E90 325i SGM
Join Date: Jun 2012
Location: GVA (BC) / Seattle (WA)

iTrader: (4)

Quote:
Originally Posted by ihsanshaik View Post
Nice writeup! I just 3m my whole plate and put it on the side. Yours looks more effective but how did this work at higher speeds?
I actually thought of taping the entire plate to the bumper as a temporary solution but I wasn't too comfortable with the plate coming so close to the bumper.

As for the speed test, I tested at about 120 km/h on a highway but that's about as fast as I'd go. For now it looks like everything's holding up.

Quote:
Originally Posted by wdeerfield View Post
Nice write up and i may consider doing this. but why not just use a bolt that screws into the tow hook opening? You could do some trial and error with length and just use a nut on the front and back of the plate holder for the correct distance out from the bumper. Maybe for version 2.
That was my initial idea actually, but after some reading it turns out that BMW uses a proprietary thread pattern. I'm sure you could bring in your tow hook to a some metal shop and have them custom thread it, but then we'd be talking about much more than $5

Quote:
Originally Posted by Slow_335i View Post
Nice info

Glad you found it helpful

one question what size drywall anchor did you have to use?
Good question, sorry I didn't mention it in tut.

It was a 1/4x3 toggle bolt anchor.
Appreciate 0
      09-26-2012, 06:36 PM   #6
CharlieBear
Second Lieutenant
4
Rep
238
Posts

Drives: 08 e92 white red sold bc uknow
Join Date: May 2012
Location: Cali

iTrader: (2)

CLEVER. looks good.
Appreciate 0
      01-02-2013, 09:07 PM   #7
USAF Rick
Private First Class
USAF Rick's Avatar
United_States
5
Rep
163
Posts

Drives: Montego Blue 08 335i e92
Join Date: Sep 2011
Location: San Diego/Riverside, CA

iTrader: (4)

Awesome write up! This saved me like $100. Thank you!
Appreciate 0
      01-03-2013, 07:48 PM   #8
j0ckinjz
Private
j0ckinjz's Avatar
1
Rep
55
Posts

Drives: 2006 330xi
Join Date: Nov 2012
Location: NY

iTrader: (0)

Looks great and I will definitely be doing this if I replace my bumper.

2 things though. In hindsight, you probably could've just put the bend with an offset to one side instead of cutting. And secondly, why not bolt the plate the bracket? Would it be too low and bracket would be showing? Maybe then you could use some thick L shaped brackets to mount the plate higher.

edit: and I don't mean higher like in the way of the headlight, I mean just the way you have it now, considering your plate holes are probably an inch higher than the bracket...
__________________
Appreciate 0
      07-22-2015, 02:09 PM   #9
puppydax
First Lieutenant
puppydax's Avatar
United_States
42
Rep
393
Posts

Drives: E92 335i
Join Date: Nov 2013
Location: Sacramento, CA

iTrader: (2)

Garage List
2007 BMW 335i  [0.00]
Bump. To the OP or anyone who did this, is it still working out for you guys? I have an E92 and a 1/4" drywall clamp wouldn't fit, had to buy a 3/8". Haven't put it in yet, but it is fairly large lol.
Appreciate 0
      08-07-2015, 03:01 PM   #10
Jarronbwall
318 turns, 11 miles, keep up
Jarronbwall's Avatar
United_States
33
Rep
430
Posts

Drives: 2009 335i
Join Date: Sep 2014
Location: Indianapolis

iTrader: (0)

Holy s**t your car is sick. Sucks you have to mount a plate in the front... Don't have that problem in Indiana. haha
__________________
335i, sport pkg, 3 pedals, 35% tint, Blacked Out, LED markers, painted brakes, OZ Superleggera wheels, S Drive tires
Custom mufflers w/ stainless Cyba tips
Tuner, downpipes, and plenty more to come
Appreciate 0
      08-08-2015, 10:37 PM   #11
gazosnic
Captain
21
Rep
900
Posts

Drives: bmw m3
Join Date: Feb 2010
Location: chicago

iTrader: (3)

Where do I look at hd to find a metal strip like that?
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 10:45 AM.




e90post
e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2016, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST