E90Post
 


PYSPEED
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > Suspension | Brakes | Chassis > Rear rotor replacement



Reply
 
Thread Tools Search this Thread
      10-08-2012, 12:33 PM   #1
easton159
Registered
 
Drives: 2007 BMW 335i
Join Date: Oct 2012
Location: Ormond Beach FL

Posts: 3
iTrader: (0)

Rear rotor replacement

Please help as I am replacing pads and rotors on my 2007 335i and am having trouble removing the rear rotor. Everything is unbolted, including the front bolt on rotor. Does parking brake have to be disengaged or possibly unhooked? This is the first wheel I have tackled and it is the passenger rear. Please help. Thanks
easton159 is offline  
0
Reply With Quote
      10-08-2012, 12:50 PM   #2
335iaz
Cause their greeaaaaat!!!!
 
Drives: SBM E90 335i
Join Date: Nov 2009
Location: Peoria, AZ

Posts: 715
iTrader: (14)

Send a message via AIM to 335iaz
you need to have the parking brake disengaged!!!

Also, get some pb blaster and squirt it around the inner part of the hub ... let that soak, and frankly since I was replacing my rotors .. I ended up taking a sledge hammer around the edge of the rotor (bang on one side .. go to the other side and bang) they finally popped off.

parking brake for sure off!
__________________
335iaz is offline   United_States
0
Reply With Quote
      10-08-2012, 01:43 PM   #3
ECSTuning
BimmerPost Supporting Vendor

 
ECSTuning's Avatar
 
Drives: Independent Tuning Specialists
Join Date: Jul 2008
Location: Ohio

Posts: 4,736
iTrader: (18)

Send a message via AIM to ECSTuning
Insure the parking brake off is off. Also often the rotor will be seized onto the hub. 335iaz's method is one that works well, just keep in mind you don't want to hit it too too hard and risk any damage to the parking brake assembly.
__________________

Have questions? Need answers? Live Chat us! 8:30am to 12:00am Midnight EST
sales@ecstuning.com | customerservice@ecstuning.com
Customer Service Hours: M - F 8:00am - 8:00pm EST | Saturday: 10:00am - 7:00pm EST
Sales Team Hours: M - F 8:00am - 11:00pm EST | Saturday: 10:00am - 7:00pm EST
Do you love surveys? Click HERE to take our Customer Satisfaction Survey!

Last edited by ECSTuning; 10-08-2012 at 04:06 PM.
ECSTuning is online now   United_States
0
Reply With Quote
      10-08-2012, 02:20 PM   #4
easton159
Registered
 
Drives: 2007 BMW 335i
Join Date: Oct 2012
Location: Ormond Beach FL

Posts: 3
iTrader: (0)

Thanks so much! That's all it took. Appreciate the help..
easton159 is offline  
0
Reply With Quote
      10-08-2012, 03:24 PM   #5
vapore0n
Lieutenant
 
Drives: 2010 335i
Join Date: Jul 2011
Location: MA

Posts: 414
iTrader: (0)

Normally, rotors have like a hole where you can screw in a bolt. This hole is in the middle area of the rotor. This will push apart the hub and rotor. Doing this is a lot safer than hammering the shit out of it.
vapore0n is offline  
0
Reply With Quote
      10-08-2012, 04:01 PM   #6
335iaz
Cause their greeaaaaat!!!!
 
Drives: SBM E90 335i
Join Date: Nov 2009
Location: Peoria, AZ

Posts: 715
iTrader: (14)

Send a message via AIM to 335iaz
Quote:
Originally Posted by vapore0n View Post
Normally, rotors have like a hole where you can screw in a bolt. This hole is in the middle area of the rotor. This will push apart the hub and rotor. Doing this is a lot safer than hammering the shit out of it.
The screw was out ... I am not saying hammer it to shit .. just saying that sometimes hitting it around the edge of the rotor helps loosen it up. The fronts for me just fell off, but they didn't want to budge at all in the rear .. even after the parking brake was off and PB blasted it
__________________
335iaz is offline   United_States
0
Reply With Quote
      10-08-2012, 07:59 PM   #7
easton159
Registered
 
Drives: 2007 BMW 335i
Join Date: Oct 2012
Location: Ormond Beach FL

Posts: 3
iTrader: (0)

Thanks so much! That's all it took. Appreciate the help..
easton159 is offline  
0
Reply With Quote
      10-08-2012, 11:51 PM   #8
335iaz
Cause their greeaaaaat!!!!
 
Drives: SBM E90 335i
Join Date: Nov 2009
Location: Peoria, AZ

Posts: 715
iTrader: (14)

Send a message via AIM to 335iaz
Glad to see you were able to change everything, did you change out the brake pad sensor? did you reset your rear brake service indicator?
__________________
335iaz is offline   United_States
0
Reply With Quote
      10-09-2012, 07:03 AM   #9
vapore0n
Lieutenant
 
Drives: 2010 335i
Join Date: Jul 2011
Location: MA

Posts: 414
iTrader: (0)

Quote:
Originally Posted by 335iaz View Post
The screw was out ... I am not saying hammer it to shit .. just saying that sometimes hitting it around the edge of the rotor helps loosen it up. The fronts for me just fell off, but they didn't want to budge at all in the rear .. even after the parking brake was off and PB blasted it
oh i know. I was talking about personal experience. On my STI I started hammering the shit out of the rotors and they wouldnt move at all. After like 30 mins I searched around for a screw that would fit the hole. The came out really easily after that.
vapore0n is offline  
0
Reply With Quote
      10-12-2012, 10:32 AM   #10
ACEE
Average Car Exceeding Expectations (ACEE)
 
ACEE's Avatar
 
Drives: 2007 335i e92
Join Date: Nov 2010
Location: Baton Rouge, La

Posts: 3,489
iTrader: (7)

Garage List
2007 e92  [3.50]
Quote:
Originally Posted by 335iaz View Post
Glad to see you were able to change everything, did you change out the brake pad sensor? did you reset your rear brake service indicator?
what he said?? I need to do this soon.
__________________
MSport front// CPS Front lip// M3 Side Skirts// Custom M3 (non wide body) rear bumper// VRS Type 1 Rear Diffuser// ACS style roof spoiler// AC Schnitzer Pedals// VRSF FMIC// Simota CF Intake// Magnaflow Axle Back// AccuAir/UAS airbags// 20" Vossen CV5 // Vredestein Tires// Custom sound sytem // BUY MY VOLKS
ACEE is offline   United_States
0
Reply With Quote
      10-13-2012, 07:48 AM   #11
Efthreeoh
Brigadier General
 
Drives: E90
Join Date: May 2012
Location: MARLAND

Posts: 3,282
iTrader: (0)

So the trick I use for rear rotors is this:

A little PB blaster at the lip of the hub. I actually use something called Kroil.

I get about an 18-inch long piece of 1 1/2 inch wood dowling (coat closet bar) and a 2-lb sledge hammer.

Hit the back side of the rotor (in the section where the caliper sits) with the hammer to the dowling. Rotate the rotor and hit it again. Go all the way around the rotor edge this way. It will pop right off (assuming you've released the P-brake).

Using a 2-lb sledge lets you use a low swing speed but still get a good amount of energy into the rotor. Using the dowling softens the blow to the rotor face and lets you resuse the rotor if you want, and allows for an open space to swing the hammer.
Efthreeoh is offline   United_States
0
Reply With Quote
      10-13-2012, 05:31 PM   #12
mapleridge
Banned
 
Drives: E90 N52 AT
Join Date: Apr 2011
Location: Vancouver, BC

Posts: 2,681
iTrader: (4)

my right rear was superseizedcity. I had to smack all around the rotor for an hour and pb blasted it to death. I thought it would never come off. They can get bad.
mapleridge is offline  
0
Reply With Quote
      10-15-2013, 09:52 PM   #13
phozenstone
Brigadier General
 
phozenstone's Avatar
 
Drives: 2007 E92 Montego Blue
Join Date: Apr 2007
Location: NY

Posts: 4,831
iTrader: (70)

Might be a stupid question but are you guys hammering the front of the rotor (side that faces the wheel) or the back? I can't seem to get enough leverage to hammer from behind the rotor but I keep seeing that everyone goes to town on their rotors with a BFH.
__________________
E92 Xdrive / Montego Blue / M3 Black Novillo Leather / OEM 351M 19" Wheels / Mtech Rear w/ IS Diffuser / Aero Lip / LCI Tailights / M3 Steering Wheel w/Paddles / 40% Huper Optik / Lux V3 / 4300K HID Fogs / Dynavin N6 / 3 Stage Intake Manifold / Magnaflow Dual Exhaust Conversion 4" Tips / K&N Filter w/ charcoal delete / Active Autowerke Stage 2 Tune / KW V1 Coilovers / BMW Performance Strut Bar
phozenstone is offline  
0
Reply With Quote
      10-15-2013, 11:56 PM   #14
Meeni
Gateropode
 
Meeni's Avatar
 
Drives: BMW 330i 06
Join Date: Apr 2012
Location: TN

Posts: 1,742
iTrader: (0)

Hammer the hat from the front. A single powerful blow is sufficient if you do it right. You want a heavy hammer. Hammering the rotor itself front or back has no effect or minor.
Meeni is online now  
0
Reply With Quote
      10-16-2013, 05:36 AM   #15
phozenstone
Brigadier General
 
phozenstone's Avatar
 
Drives: 2007 E92 Montego Blue
Join Date: Apr 2007
Location: NY

Posts: 4,831
iTrader: (70)

Thanks will try again today once I get a dead blow hammer
__________________
E92 Xdrive / Montego Blue / M3 Black Novillo Leather / OEM 351M 19" Wheels / Mtech Rear w/ IS Diffuser / Aero Lip / LCI Tailights / M3 Steering Wheel w/Paddles / 40% Huper Optik / Lux V3 / 4300K HID Fogs / Dynavin N6 / 3 Stage Intake Manifold / Magnaflow Dual Exhaust Conversion 4" Tips / K&N Filter w/ charcoal delete / Active Autowerke Stage 2 Tune / KW V1 Coilovers / BMW Performance Strut Bar
phozenstone is offline  
0
Reply With Quote
      10-16-2013, 05:29 PM   #16
phozenstone
Brigadier General
 
phozenstone's Avatar
 
Drives: 2007 E92 Montego Blue
Join Date: Apr 2007
Location: NY

Posts: 4,831
iTrader: (70)

I used a 3lb dead blow and pounded the hat for about 20 minutes with no luck. Ebrake is off and retainer screw is off. Any other methods before I give up and being it to an Indy?
__________________
E92 Xdrive / Montego Blue / M3 Black Novillo Leather / OEM 351M 19" Wheels / Mtech Rear w/ IS Diffuser / Aero Lip / LCI Tailights / M3 Steering Wheel w/Paddles / 40% Huper Optik / Lux V3 / 4300K HID Fogs / Dynavin N6 / 3 Stage Intake Manifold / Magnaflow Dual Exhaust Conversion 4" Tips / K&N Filter w/ charcoal delete / Active Autowerke Stage 2 Tune / KW V1 Coilovers / BMW Performance Strut Bar
phozenstone is offline  
0
Reply With Quote
      10-16-2013, 08:00 PM   #17
AllBlackBimmer
Lieutenant Colonel
 
AllBlackBimmer's Avatar
 
Drives: 2008 328i E90
Join Date: Aug 2011
Location: Central PA area

Posts: 1,526
iTrader: (0)

Spray the hell out of it with wd40 and let it soak...

Had same problem, tried for over an hour at first without luck. I was afraid of damaging the bearings slamming it with a sledge even though did give a few whacks.

Then let it soda overnight in wd40.... 5 mins the next day and both rear rotors were off.
__________________
2008 328i E90 Jet Black:6MT:Premium:Sport:Walnut/Black interior:Xenon:MTEC V3 AEs:19" Beyern Mesh:35% Tint:Blacklines:OEM Front Splitters
AllBlackBimmer is offline  
0
Reply With Quote
      10-17-2013, 09:54 PM   #18
Jklad
Lieutenant
 
Jklad's Avatar
 
Drives: 2007 335i Coupe
Join Date: Nov 2010
Location: Palatine, IL

Posts: 506
iTrader: (0)

Yes my rears took some time and I was worried they would not come off. Sprayed pb blaster in each rotor hole, center Hub, anywhere I could, about 3 separate times, and then took my time hammering around the rotor, turning rotor then hammering from behind. Eventually they came off after about 30 min each of spraying and pounding. good idea to have a cloth or something to place between hammer and rotor to cushion the blow.
Jklad is online now   United_States
0
Reply With Quote
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 03:43 PM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST