E90Post
 


Bimmer Retrofit
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > Mechanical Maintenance: Break-in / Oil & Fluids / Servicing / Warranty > Brake service at 71k.. change rotors?!



Reply
 
Thread Tools Search this Thread
      12-07-2012, 08:43 PM   #1
mJ335
Amateur Post Whore
 
mJ335's Avatar
 
Drives: 07 E90 SparkLiN G. 335i
Join Date: Sep 2007
Location: SocaL

Posts: 3,037
iTrader: (17)

Garage List
2007 e90 335i  [0.00]
Brake service at 71k.. change rotors?!

Hi guys,

My car is at 71,652 and the brake light just came on... so I went to a bodyshop that specializes in BMWs (knowing that stealerships will rip me off) and they tell me that the brake service consists of changing brake pads, brake sensors... and ROTORS?! My rotors are fine (no hot spots), only the brake pads are worn.. so my question is, is it absolutely necessary to replace brake rotors at 71k miles? Or are they just trying to take my money as well? Any helpful input would be greatly appreciated.. thanks!
__________________
Go WiTh ThE FLoW.

|BL|RS|PIAA|CFE|CFMC|SSM|CFG|CFDP|ABG|M6|AFE|MTECH |RPI|JB+|CSLT|KWSC|
mJ335 is offline  
0
Reply With Quote
      12-07-2012, 08:54 PM   #2
Slow_335i
Daily Driven!
 
Slow_335i's Avatar
 
Drives: BMW 335i
Join Date: Jun 2011
Location: Peoria IL

Posts: 2,490
iTrader: (11)

Garage List
2008 BMW 335I  [3.32]
If they've never been changed it may be the best time to do it now and save the extra labor cost next time.

But really if theres enough "meat" on them you should be good.
__________________
Slow_335i is offline   United_States
0
Reply With Quote
      12-08-2012, 03:13 AM   #3
Meeni
Gateropode
 
Meeni's Avatar
 
Drives: BMW 330i 06
Join Date: Apr 2012
Location: TN

Posts: 1,783
iTrader: (0)

Its not abnormal to change rotors at this mileage, if they are not completely done, they are close. If you don't trust "them" you can check they are within spec yourself (vw video, but same for us)


spec if 20.4mm on 335i .

Last edited by Meeni; 12-08-2012 at 03:20 AM.
Meeni is offline  
0
Reply With Quote
      12-08-2012, 07:31 AM   #4
Efthreeoh
Brigadier General
 
Drives: E90
Join Date: May 2012
Location: MARLAND

Posts: 3,422
iTrader: (0)

So here's my opinion on the question from 25 years of experience with DIYing BMW brake systems.

You can leave the rotors and just change the pads at 71K. However you will find that the new pads will last longer than the original rotors. This is usually the case because OE BMW rotors are somewhat "soft" and wear while in service and usually do not last through two sets of pads and end up with warped rotors and 35% pad life left (estimates).

Additionally, an ideal brake "relining" includes removal of the rotors and resurfacing them on a brake lathe. The resurfacing removes even more rotor material and makes them more susceptible to warpage from heat as the rotors continue to wear. All that said, it is just better to replace the rotors and pads as a set since some of the cost of the brake job should be for resurfacing the rotors, which can be offset by just buying new rotors instead. Meaning, if it costs $20 to resurface one rotor and a new rotor costs $65, the $20 is better spend just getting a new rotor.
Efthreeoh is offline   United_States
0
Reply With Quote
      12-08-2012, 01:17 PM   #5
queensfield
First Lieutenant
 
Drives: 2006 330i E90
Join Date: Aug 2011
Location: So Cal

Posts: 343
iTrader: (0)

Great advice and I had the exact same experience. Best to replace both rotor and brake pads. Make sure you use a new brake wear sensor at the same time and it is installed correctly (otherwise it makes a squeeky noise at low rpms).
queensfield is offline   United_States
0
Reply With Quote
      12-08-2012, 11:38 PM   #6
Fitz335
Private First Class
 
Fitz335's Avatar
 
Drives: 2007 335i Black
Join Date: Oct 2012
Location: Sicily

Posts: 178
iTrader: (0)

Garage List
2007 335i  [0.00]
How big of a lip on the rotor would you consider to be "worn"?
Fitz335 is offline  
0
Reply With Quote
      12-17-2012, 01:31 PM   #7
mJ335
Amateur Post Whore
 
mJ335's Avatar
 
Drives: 07 E90 SparkLiN G. 335i
Join Date: Sep 2007
Location: SocaL

Posts: 3,037
iTrader: (17)

Garage List
2007 e90 335i  [0.00]
Thank you for your great advice! After looking through, I decided to change everything (rotors, sensors, pads), just to think of saving money in the long run.. appreciate your input.
__________________
Go WiTh ThE FLoW.

|BL|RS|PIAA|CFE|CFMC|SSM|CFG|CFDP|ABG|M6|AFE|MTECH |RPI|JB+|CSLT|KWSC|
mJ335 is offline  
0
Reply With Quote
      12-19-2012, 08:20 AM   #8
dd243372
Second Lieutenant
 
dd243372's Avatar
 
Drives: Jet Black E90 328i LCI
Join Date: Feb 2012
Location: Bronx, NY

Posts: 249
iTrader: (0)

Good thread. Answered a question I was wondering myself.
__________________
______________________________
dd243372 is offline   United_States
0
Reply With Quote
      12-27-2012, 04:15 AM   #9
r111
Private
 
Drives: 996 C2
Join Date: Mar 2005
Location: San Francisco

Posts: 64
iTrader: (0)

I'm a free way driver so, my third set of pads are installed when the car is at 150,000 miles. The rotors are fused to the hub, and are hard to take off. You have to get really good with aiming with the hammer.

Make sure the shop uses anti-seize paste on the hub to rotor mating surface. It will save you trouble later down the line.
r111 is offline  
0
Reply With Quote
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 03:13 AM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST