E90Post
 


Bimmertech
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Powertrain and Drivetrain Discussions > N54 Turbo Engine / Drivetrain / Exhaust Modifications - 335i > "Devils own" meth kit W/4-AN fitting & Race tank review



Reply
 
Thread Tools Search this Thread
      01-26-2013, 04:20 PM   #1
robc1976
DIYER
 
robc1976's Avatar
 
Drives: E90 335i
Join Date: Mar 2012
Location: Illinois

Posts: 4,227
iTrader: (11)

"Devils own" meth kit W/4-AN fitting & Race tank review

Decided to upgrade my meth kit because my other kit (not getting into wich one, this is a review not a bash thread LOL!!) was having issues with air in the lines. I contact Devils own and ordered the following below and it intergrates with the JB4 FSB perfectly. Devils own customer service is way above expectations...aswered every Email and I was able to tell them the length of the lines I needed and the kit was shipped the next day!

Tank: I LOVE this tank...has a baffle/sump built in so you can take the fluid down low (I never do) and is beneficial when taking hard corners ect. The tank is built exactly like a fuel cell...VERY thick....you could stand on this tghing and it wouyld not budge. The lid is awesome...seals very well and tou just twist the insert and it suctions down..twist in oposite direction and un-seals. I also like the vented allen screw fitting, not just a hole drilled in the tanks cap.









Note: If you get the race tank you will have to have push in fittings from pump to tank.

Fittings: Greatest part of kit, so much easier to purge your systen not fighting a "push in fitting" and the nozzle just stays in place forever (unless you have to clean the nozzle).







Nozzle/Nozzle holder: I really like the design of there nozzle with the screw in filter. I love the Nozzle holder with the 4-An fitting as stated above...easy to purge and the Nozzle holder will alow you to use a CM nozzle also.







Selonoid: Pretty much all are the same, except I do like the thicker wires on this unit and of course the 4-AN fittings.



Pump: Works great, pumps are pretty much the same also...this one is rated at 250 psi.



Installed pics/Notes:

If you run yours like I did You will need 1X 14 ft hose (Had a foot extra just incase) 1X 10" piece (From selonoid to nozzle.

Note: If you have 4-AN fittings on tank you will need a 2-3 foot piece here with a 90 degree fitting on your line....depends on your set-up.









I am VERY satisfied with this set-up, meth flows great and response is instant:

Log:

__________________
JB4 G5, WEDGE flash, 455 LPFP, HFS-4 meth kit, BMS OCC, RB turbos W/3.5 N20 sensor, RB valve, BMS DCI, 3" AR Dps, Custom OC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, Meyle HD tie-rods, HPA rear toe arms, Wavetrac LSD, DEFIV kit, KW clubsport coilovers, Power-Flex subframe bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, MORR VS8.2 rims 245/295
robc1976 is offline  
0
Reply With Quote
      01-26-2013, 05:55 PM   #2
4doorbmwpower
Lieutenant
 
4doorbmwpower's Avatar
 
Drives: Blue E90 335i
Join Date: Nov 2010
Location: North Carolina

Posts: 590
iTrader: (0)

Send a message via Skype™ to 4doorbmwpower
how does it integrate? do u have JB4 and it just plug n plaY?
4doorbmwpower is offline   United_States
0
Reply With Quote
      01-26-2013, 06:23 PM   #3
robc1976
DIYER
 
robc1976's Avatar
 
Drives: E90 335i
Join Date: Mar 2012
Location: Illinois

Posts: 4,227
iTrader: (11)

Quote:
Originally Posted by 4doorbmwpower View Post
how does it integrate? do u have JB4 and it just plug n plaY?
intergrates with the BMS FSB via the selonoid.
__________________
JB4 G5, WEDGE flash, 455 LPFP, HFS-4 meth kit, BMS OCC, RB turbos W/3.5 N20 sensor, RB valve, BMS DCI, 3" AR Dps, Custom OC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, Meyle HD tie-rods, HPA rear toe arms, Wavetrac LSD, DEFIV kit, KW clubsport coilovers, Power-Flex subframe bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, MORR VS8.2 rims 245/295
robc1976 is offline  
0
Reply With Quote
      01-30-2013, 08:51 PM   #4
robc1976
DIYER
 
robc1976's Avatar
 
Drives: E90 335i
Join Date: Mar 2012
Location: Illinois

Posts: 4,227
iTrader: (11)

Moved the selonoid much closer (From 12" to 3") to nozzle, less drain and possible better response.





__________________
JB4 G5, WEDGE flash, 455 LPFP, HFS-4 meth kit, BMS OCC, RB turbos W/3.5 N20 sensor, RB valve, BMS DCI, 3" AR Dps, Custom OC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, Meyle HD tie-rods, HPA rear toe arms, Wavetrac LSD, DEFIV kit, KW clubsport coilovers, Power-Flex subframe bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, MORR VS8.2 rims 245/295
robc1976 is offline  
0
Reply With Quote
      01-30-2013, 09:02 PM   #5
GetSomeE92
Major
 
Drives: '09 Space Gray E92
Join Date: Mar 2011
Location: Miami, FL

Posts: 1,060
iTrader: (7)

Looks good. What lengths did you end up needing for the stainless steel lines? Would they be the same for an E92?
GetSomeE92 is offline   United_States
0
Reply With Quote
      01-30-2013, 09:25 PM   #6
Brian@MWP
Private
 
Drives: BMW
Join Date: Jan 2013
Location: Chicago

Posts: 90
iTrader: (0)

I wasnt a big fan for meth injection but lets say that changed after i took a ride in a 335i with meth injection + a lot of other upgrades! Clean install
Brian@MWP is offline   United_States
0
Reply With Quote
      01-30-2013, 09:48 PM   #7
robc1976
DIYER
 
robc1976's Avatar
 
Drives: E90 335i
Join Date: Mar 2012
Location: Illinois

Posts: 4,227
iTrader: (11)

Quote:
Originally Posted by GetSomeE92 View Post
Looks good. What lengths did you end up needing for the stainless steel lines? Would they be the same for an E92?
depends on how you install it...mine where 14 ft and I had 1ft+ left over and a 3' line from nozzle to selonoid....on a E92 it would be at least 18" shorter than that...around 12 ft I would guess.
__________________
JB4 G5, WEDGE flash, 455 LPFP, HFS-4 meth kit, BMS OCC, RB turbos W/3.5 N20 sensor, RB valve, BMS DCI, 3" AR Dps, Custom OC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, Meyle HD tie-rods, HPA rear toe arms, Wavetrac LSD, DEFIV kit, KW clubsport coilovers, Power-Flex subframe bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, MORR VS8.2 rims 245/295
robc1976 is offline  
0
Reply With Quote
      01-30-2013, 09:49 PM   #8
robc1976
DIYER
 
robc1976's Avatar
 
Drives: E90 335i
Join Date: Mar 2012
Location: Illinois

Posts: 4,227
iTrader: (11)

Quote:
Originally Posted by Brian@MWP View Post
I wasnt a big fan for meth injection but lets say that changed after i took a ride in a 335i with meth injection + a lot of other upgrades! Clean install
Thanks man, yeah I had to have it with RB's...only way to max them out LOL!!
__________________
JB4 G5, WEDGE flash, 455 LPFP, HFS-4 meth kit, BMS OCC, RB turbos W/3.5 N20 sensor, RB valve, BMS DCI, 3" AR Dps, Custom OC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, Meyle HD tie-rods, HPA rear toe arms, Wavetrac LSD, DEFIV kit, KW clubsport coilovers, Power-Flex subframe bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, MORR VS8.2 rims 245/295
robc1976 is offline  
0
Reply With Quote
      01-30-2013, 11:37 PM   #9
Jeff@TopGearSolutions
BimmerPost Supporting Vendor

 
Jeff@TopGearSolutions's Avatar
 
Drives: C6 Z06, GSXR-750, 09 335i
Join Date: Dec 2008
Location: TopGearSolutions.com

Posts: 16,806
iTrader: (31)

Send a message via AIM to Jeff@TopGearSolutions
Wow great thread. This will help answer a lot of questions for some of my customers.

It should be noted and you mentioned above Devils Own Stainless steel lines can be custom made to fit you needs you just need to know the sizes you need. Since every kit may be a little different along with the orientation its up to the end user to know and decide what they need.

Great thread!
Jeff@TopGearSolutions is offline   United_States
0
Reply With Quote
      01-30-2013, 11:46 PM   #10
robc1976
DIYER
 
robc1976's Avatar
 
Drives: E90 335i
Join Date: Mar 2012
Location: Illinois

Posts: 4,227
iTrader: (11)

Quote:
Originally Posted by Jeff@TopGearSolutions View Post
Wow great thread. This will help answer a lot of questions for some of my customers.

It should be noted and you mentioned above Devils Own Stainless steel lines can be custom made to fit you needs you just need to know the sizes you need. Since every kit may be a little different along with the orientation its up to the end user to know and decide what they need.

Great thread!
Thanks man!!

totall agree, there are so many ways to route the line it can vary easily. I always think a bit to much is better than not enough! Also, some CP's have different meth bung configurations.

I may go to a dual nozzle (DO7 & DO10) wich devils own also has in 4-AN.

Also: 90 degree fittings can be added to any line for no extra charge.
__________________
JB4 G5, WEDGE flash, 455 LPFP, HFS-4 meth kit, BMS OCC, RB turbos W/3.5 N20 sensor, RB valve, BMS DCI, 3" AR Dps, Custom OC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, Meyle HD tie-rods, HPA rear toe arms, Wavetrac LSD, DEFIV kit, KW clubsport coilovers, Power-Flex subframe bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, MORR VS8.2 rims 245/295
robc1976 is offline  
0
Reply With Quote
      01-30-2013, 11:51 PM   #11
robc1976
DIYER
 
robc1976's Avatar
 
Drives: E90 335i
Join Date: Mar 2012
Location: Illinois

Posts: 4,227
iTrader: (11)

Here are the parts I got:


Here is what I got:

250psi pump:

http://www.alcohol-injection.com/en/...tion-pump.html

4-AN Stainless line upgraded: (Comes with nozzle holder, pump fittings, selonoid fittings) but be sure to put in comments you are NOT using a ckeckvalve but a 250 psi selonoid.

http://www.alcohol-injection.com/en/...-line-set.html

250psi Selonoid: (Be sure to select 4-AN)

http://www.alcohol-injection.com/en/...-solenoid.html

Nozzle: (Depends on your mods.....I have the largest DO14)

http://www.alcohol-injection.com/en/49-nozzles

Tank: (If getting race tank you will need a push in fitting on inlet of pump)

http://www.alcohol-injection.com/en/...mped-tank.html

You will need a BMS FSB (if using a JB4):
__________________
JB4 G5, WEDGE flash, 455 LPFP, HFS-4 meth kit, BMS OCC, RB turbos W/3.5 N20 sensor, RB valve, BMS DCI, 3" AR Dps, Custom OC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, Meyle HD tie-rods, HPA rear toe arms, Wavetrac LSD, DEFIV kit, KW clubsport coilovers, Power-Flex subframe bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, MORR VS8.2 rims 245/295
robc1976 is offline  
0
Reply With Quote
      01-30-2013, 11:53 PM   #12
GetSomeE92
Major
 
Drives: '09 Space Gray E92
Join Date: Mar 2011
Location: Miami, FL

Posts: 1,060
iTrader: (7)

Quote:
Originally Posted by robc1976 View Post
depends on how you install it...mine where 14 ft and I had 1ft+ left over and a 3' line from nozzle to selonoid....on a E92 it would be at least 18" shorter than that...around 12 ft I would guess.
Good stuff. I guest the best plan would be to use some rope/string and run it where I plan to run the lines and measure it up.
GetSomeE92 is offline   United_States
0
Reply With Quote
      01-30-2013, 11:54 PM   #13
robc1976
DIYER
 
robc1976's Avatar
 
Drives: E90 335i
Join Date: Mar 2012
Location: Illinois

Posts: 4,227
iTrader: (11)

Quote:
Originally Posted by GetSomeE92 View Post
Good stuff. I guest the best plan would be to use some rope/string and run it where I plan to run the lines and measure it up.
I used my old tubing....made a 6 ft piece and just ran it.
__________________
JB4 G5, WEDGE flash, 455 LPFP, HFS-4 meth kit, BMS OCC, RB turbos W/3.5 N20 sensor, RB valve, BMS DCI, 3" AR Dps, Custom OC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, Meyle HD tie-rods, HPA rear toe arms, Wavetrac LSD, DEFIV kit, KW clubsport coilovers, Power-Flex subframe bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, MORR VS8.2 rims 245/295
robc1976 is offline  
0
Reply With Quote
      01-31-2013, 12:03 AM   #14
Torres_335i
Banned
 
Torres_335i's Avatar
 
Drives: E92 Bsm 335i
Join Date: Sep 2011
Location: long island

Posts: 93
iTrader: (1)

Quote:
Originally Posted by robc1976 View Post
I used my old tubing....made a 6 ft piece and just ran it.
how did you wire the FSB?
Torres_335i is offline  
0
Reply With Quote
      01-31-2013, 12:09 AM   #15
robc1976
DIYER
 
robc1976's Avatar
 
Drives: E90 335i
Join Date: Mar 2012
Location: Illinois

Posts: 4,227
iTrader: (11)

Quote:
Originally Posted by Torres_335i View Post
how did you wire the FSB?
Wire's up just like the cool mist selonoid does...there are 2 wires and one goes to the green wire (flow) and the other one goes to the red pump wire and inline fuse (power). Wires are not polarity specific.
__________________
JB4 G5, WEDGE flash, 455 LPFP, HFS-4 meth kit, BMS OCC, RB turbos W/3.5 N20 sensor, RB valve, BMS DCI, 3" AR Dps, Custom OC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, Meyle HD tie-rods, HPA rear toe arms, Wavetrac LSD, DEFIV kit, KW clubsport coilovers, Power-Flex subframe bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, MORR VS8.2 rims 245/295
robc1976 is offline  
0
Reply With Quote
      01-31-2013, 12:24 AM   #16
GetSomeE92
Major
 
Drives: '09 Space Gray E92
Join Date: Mar 2011
Location: Miami, FL

Posts: 1,060
iTrader: (7)

Quote:
Originally Posted by robc1976 View Post
I used my old tubing....made a 6 ft piece and just ran it.
I'm not running a meth system at the moment, so I'll be putting it together from scratch. You've been a huge help, though. I always felt the standard kits left a little on the table when it came to leak prevention. Appreciate it.
GetSomeE92 is offline   United_States
0
Reply With Quote
      01-31-2013, 12:29 AM   #17
Jeff@TopGearSolutions
BimmerPost Supporting Vendor

 
Jeff@TopGearSolutions's Avatar
 
Drives: C6 Z06, GSXR-750, 09 335i
Join Date: Dec 2008
Location: TopGearSolutions.com

Posts: 16,806
iTrader: (31)

Send a message via AIM to Jeff@TopGearSolutions
Quote:
Originally Posted by robc1976 View Post
Thanks man!!

totall agree, there are so many ways to route the line it can vary easily. I always think a bit to much is better than not enough! Also, some CP's have different meth bung configurations.

I may go to a dual nozzle (DO7 & DO10) wich devils own also has in 4-AN.

Also: 90 degree fittings can be added to any line for no extra charge.

Yea the D014 is quite an agressive nozzle. Your better off with 2 smaller nozzles. When you go over 10 it turns into a fire hose and atomization really goes down the tubes, no pun intended.
Jeff@TopGearSolutions is offline   United_States
0
Reply With Quote
      01-31-2013, 12:32 AM   #18
Torres_335i
Banned
 
Torres_335i's Avatar
 
Drives: E92 Bsm 335i
Join Date: Sep 2011
Location: long island

Posts: 93
iTrader: (1)

Quote:
Originally Posted by Jeff@TopGearSolutions View Post
Yea the D014 is quite an agressive nozzle. Your better off with 2 smaller nozzles. When you go over 10 it turns into a fire hose and atomization really goes down the tubes, no pun intended.
so is d010 fine for a simple setup like this?
Torres_335i is offline  
0
Reply With Quote
      01-31-2013, 12:34 AM   #19
robc1976
DIYER
 
robc1976's Avatar
 
Drives: E90 335i
Join Date: Mar 2012
Location: Illinois

Posts: 4,227
iTrader: (11)

Quote:
Originally Posted by Jeff@TopGearSolutions View Post
Yea the D014 is quite an agressive nozzle. Your better off with 2 smaller nozzles. When you go over 10 it turns into a fire hose and atomization really goes down the tubes, no pun intended.
lol!!! Plus I am running a 80-90 additive (N20 sensor alows higher additives). Do you think a DO7 and DO10 sounds good? That DO14 is a fire hose! I saw a supra with 5 DO14's man....I was like
__________________
JB4 G5, WEDGE flash, 455 LPFP, HFS-4 meth kit, BMS OCC, RB turbos W/3.5 N20 sensor, RB valve, BMS DCI, 3" AR Dps, Custom OC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, Meyle HD tie-rods, HPA rear toe arms, Wavetrac LSD, DEFIV kit, KW clubsport coilovers, Power-Flex subframe bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, MORR VS8.2 rims 245/295
robc1976 is offline  
0
Reply With Quote
      01-31-2013, 12:37 AM   #20
robc1976
DIYER
 
robc1976's Avatar
 
Drives: E90 335i
Join Date: Mar 2012
Location: Illinois

Posts: 4,227
iTrader: (11)

Quote:
Originally Posted by Torres_335i View Post
so is d010 fine for a simple setup like this?
depends on your mods....with me hitting 22psi I will need more meth than say someone with 15-18psi. Most setups would do fine with a DO10.
__________________
JB4 G5, WEDGE flash, 455 LPFP, HFS-4 meth kit, BMS OCC, RB turbos W/3.5 N20 sensor, RB valve, BMS DCI, 3" AR Dps, Custom OC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, Meyle HD tie-rods, HPA rear toe arms, Wavetrac LSD, DEFIV kit, KW clubsport coilovers, Power-Flex subframe bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, MORR VS8.2 rims 245/295
robc1976 is offline  
0
Reply With Quote
      01-31-2013, 12:39 AM   #21
Torres_335i
Banned
 
Torres_335i's Avatar
 
Drives: E92 Bsm 335i
Join Date: Sep 2011
Location: long island

Posts: 93
iTrader: (1)

Quote:
Originally Posted by robc1976 View Post
depends on your mods....with me hitting 22psi I will need more meth than say someone with 15-18psi. Most setups would do fine with a DO10.
i was gonna order a bms kit until i saw yours looks more secure and safe.
how did you get the handle on there?
Torres_335i is offline  
0
Reply With Quote
      01-31-2013, 12:40 AM   #22
robc1976
DIYER
 
robc1976's Avatar
 
Drives: E90 335i
Join Date: Mar 2012
Location: Illinois

Posts: 4,227
iTrader: (11)

Quote:
Originally Posted by Torres_335i View Post
i was gonna order a bms kit until i saw yours looks more secure and safe.
how did you get the handle on there?
that just screws in from the bottom, drill 2 holes and screw in, 5 min install.
__________________
JB4 G5, WEDGE flash, 455 LPFP, HFS-4 meth kit, BMS OCC, RB turbos W/3.5 N20 sensor, RB valve, BMS DCI, 3" AR Dps, Custom OC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, Meyle HD tie-rods, HPA rear toe arms, Wavetrac LSD, DEFIV kit, KW clubsport coilovers, Power-Flex subframe bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, MORR VS8.2 rims 245/295
robc1976 is offline  
0
Reply With Quote
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 10:10 AM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST