[GenePoole]

Originally Posted by rich123321

No. Use winkfp to program the module to the new vin. No other way

It should be noted that WinKFP will update the VIN only if the firmware is also updated. If the firmware is already the latest, WinKFP will go through all the motions, but in the end, no update will have been performed and the VIN will still be the old VIN. In this case, probably your only option is Tool32, but be forewarned, it is not very intuitive. I wish I'd wrote it down or took screen shots as I can't remember the steps.

[franzzz]

Originally Posted by GenePoole

It should be noted that WinKFP will update the VIN only if the firmware is also updated. If the firmware is already the latest, WinKFP will go through all the motions, but in the end, no update will have been performed and the VIN will still be the old VIN. In this case, probably your only option is Tool32, but be forewarned, it is not very intuitive. I wish I'd wrote it down or took screen shots as I can't remember the steps.

Wait for screenshot
tnx

[zigsman]

I have spent weeks getting GT1/DIS and SSS/Progman installed on my laptop. I have an 06 E90 with a build date of 06/05. I have windows 7 x64 with VMWare installed. I have two VM's installed, one for GT1 and one for SSS, both independent of each other. Both programs run just fine and I can access all the menus, however, my K + KCAN cable will not communicate with the programs. I have INPA installed as well as NCS Expert as well. INPA is on the x64 system and works just fine; I can cycle through all the menus and communicate with the car. NCS works great in XP mode and I can successfully code using it. I followed the installation guide to the "T" for SSS and GT1 but cannot seem to get the cable to communicate. In SSS I set the gateway to 192.168.68.1 and the IP address to 192.168.50 during installation. When I pull up the network page in SSS, it shows the address as 192.168.68.30 and the gateway is blank. I changed these to the original values and restart the machine but the changes do not hold. I have tried running the programs with DiagHead running, IFH running and EDIABAS Server running as well...still no luck. I have a battery charger hooked up pushing 12V at 13A to the car while attempting to code, so power should not be an issue and I never get a "low batt" warning from the car. The COM port is set to "1". I am out of ideas here! Does anyone here know how to achieve communication between the car and SSS and GT1!!?? I've spent a couple of days thumbing through message boards and searching Google with no luck...

SSS Version: 3.1
Progman Version: 32

SSS Network Configuration:
IP - 192.168.68.30
Subnet - 255.255.255.0
gateway - 192.168.68.1

Interface IP - 192.168.68.1

SSS Overview shows the operating status as usable with an IP of 192.168.68.4

SSS Connection Test: unsuccessful

SSS Connection Error: Initialization was unsuccessful. Make sure with diagnosis that access to the vehicle is possible. Terminate program. If this happens repeatedly, further information can be obtained from Technical Market Support.

GT1 Connection Error in diagnostics: Communication between operation unit and diagnostic head is impaired. Fault number: 200.159

GT1 Connection Error in coding: Connect diagnosis connector to vehicle! Switch on ignition! Start automatic vehicle identification!

DiagHead window: After it is started, it shows an IP of 192.168.68.1, mask of 255.255.255.0 for the VMware Virtual Ethernet Adapter for VMnet1. It continually repeats "Sending CMD_MT_FREE and in the bottom of the window it shows "Test LED Disconnected"

I know this outfit works on Windows 7 x64, that is what this package download and install instructions were designed for (I've read in several threads that folks are running it as such). I just need to figure out how to get the communication going between the car and program. If anyone would like a link to the package and instructions, let me know.

I attached screenshots for anyone interested in looking.....

What a PITA!

[dave4]

Can someone upload the NCSexpert somewhere and share the link? The one on the first page does not work anymore.

[j0ckinjz]

Originally Posted by dave4

Can someone upload the NCSexpert somewhere and share the link? The one on the first page does not work anymore.

I believe this is everything that was in the original zip...

https://mega.co.nz/#!4pclWIKR!DnCZtWJsUOiQJsV_tnLKdCr4mShOa2Dawry7Ue0cA9Q

[dave4]

Originally Posted by j0ckinjz

I believe this is everything that was in the original zip...

https://mega.co.nz/#!4pclWIKR!DnCZtWJsUOiQJsV_tnLKdCr4mShOa2Dawry7Ue0cA9Q

Thank You!!!

[comaing83]

the software link does not work.
Where can i download those software????????

[325i_racer]

anyone from Seattle successfully installed and able to complete the coding? I would pay someone to code my car please. pm me. I have 07 325i and 09 X5 with m package

[Lifted07Duramax]

Is this how I'd turn off my bet corners in headlight

[Ruhnie]

Is the cable from one-stop-electronics still the best recommended cable?

[Krozking]

Originally Posted by j0ckinjz

I believe this is everything that was in the original zip...

https://mega.co.nz/#!4pclWIKR!DnCZtWJsUOiQJsV_tnLKdCr4mShOa2Dawry7Ue0cA9Q

Thanks so much for this...I hope this one works for me!

[franzzz]

Originally Posted by franzzz

Wait for screenshot
tnx

Ok Mulf updated !

2 hour for programming

[j0ckinjz]

I decided to put together another folder of files. It pretty much explains how to install tools 2.12 and update daten files to v48. It includes files from here and other places too. 2.12 is only really needed if you need/want to install on a x64 OS. I successfully installed and tested NCS Expert coding on my KOMBI module.

Also, this is more of a Lite version only mean to enable basic functions and coding. I haven't got much passed that myself.

Here are the files:

https://mega.co.nz/#!lxVQBQII!TNv7GBkXJAieHs2hEcFV13KR3iVcBXkqxlEctQ1vpTU

[franzzz]

Originally Posted by j0ckinjz

I decided to put together another folder of files. It pretty much explains how to install tools 2.12 and update daten files to v48. It includes files from here and other places too. 2.12 is only really needed if you need/want to install on a x64 OS. I successfully installed and tested NCS Expert coding on my KOMBI module.

Also, this is more of a Lite version only mean to enable basic functions and coding. I haven't got much passed that myself.

Here are the files:

https://mega.co.nz/#!lxVQBQII!TNv7GBkXJAieHs2hEcFV13KR3iVcBXkqxlEctQ1vpTU

Great
Work fine

only my trasmission modul is not detected
(steptronic S GS19D)
Inpa not find GS19D (ipo file i think)

[j0ckinjz]

Originally Posted by franzzz

Great
Work fine

only my trasmission modul is not detected
(steptronic S GS19D)
Inpa not find GS19D (ipo file i think)

The only file I have is a GS19D.PRG file in the ECU folder.

[adriang]

Originally Posted by Fmstrat

Hi all,

Tried everything I could find in the thread, including multiple cables, but still having issues.

2008 BMW 335i

The first cable I tried showed black dots for both Battery and Ignition, but INPA kept giving errors that searching proved to likely be a cable issue. So I replaced with...

• This cable: http://www.ebay.com/itm/160845701117...84.m1439.l2649 (Everyone in forums recommended it)
• I'm using it without the adapter (since it's a 2008 and pin 8 should be open)
• I've tried drivers from this thread, v2.6 from another thread, and v2.8 from here: http://www.ftdichip.com/Drivers/VCP.htm which is the actual chipset manufacturer for the device.
• I've tried on a WinXP 32bit netbook, and a VMWare Fusion WinXP 32bit install with the same results

Black dot for battery, no black dot for ignition. Just to give it a shot, I tried to register my new battery in Tool32.exe, and it "appeared" to work.

Any idea what's going on? Any way to confirm if battery registration worked?

Thanks,
Ben

I've been having the same black dot for battery and no black dot for ignition.

Would like an answer too..

[joeyaoyp]

hi, could you pls. pls help me? i set up every thing done,i run the obd set up, every thing is good. but it still can not connect to my car, whats wrong with it?

[joeyaoyp]

some one can help me or give me a link about the set up?i am gonna crazy@@@@

[franzzz]

Originally Posted by j0ckinjz

The only file I have is a GS19D.PRG file in the ECU folder.

No problem
I found the missing files (gs19d.ipo) in the old SP-DATEN V40

[Gemcoska]

Did this thread die at 199 pages?

[GSBruce]

Is there a coder in the Houston, Texas area? I own 1% of a small craft brewery and can either trade you green paper of excellent beer for your time and help - I have a pesky intermittent exterior light warning code, yet all of my exterior lights are burning and functioning properly.

2007 BMW 328xi

[shawnsheridan]

Originally Posted by GSBruce

Is there a coder in the Houston, Texas area? I own 1% of a small craft brewery and can either trade you green paper of excellent beer for your time and help - I have a pesky intermittent exterior light warning code, yet all of my exterior lights are burning and functioning properly.

2007 BMW 328xi

Call me when you get an F30.