E90Post
 


Bimmertech
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > Suspension | Brakes | Chassis > 2006 330xi and Koni FSD



Reply
 
Thread Tools Search this Thread
      04-21-2013, 10:52 PM   #1
jacobsed
Lieutenant
 
Drives: 2006 330xi
Join Date: Feb 2012
Location: United States

Posts: 425
iTrader: (2)

2006 330xi and Koni FSD

I'm going to install a set of Konis FSD on my 330xi. Is there anything else I need to purchase for this job? I have 136k miles and right now my plan is to just buy the set of FSD's. Thanks in advance!
jacobsed is offline  
0
Reply With Quote
      04-21-2013, 11:40 PM   #2
mike-y
just another bmw douche bag
 
Drives: 1.9L of fury
Join Date: Nov 2008
Location: Los Angeles, CA

Posts: 3,396
iTrader: (4)

you may want to get a new pair of upper guide supports, since the bearings inside of them may be getting worn out at that mileage.
mike-y is offline   United_States
0
Reply With Quote
      04-22-2013, 05:21 AM   #3
jacobsed
Lieutenant
 
Drives: 2006 330xi
Join Date: Feb 2012
Location: United States

Posts: 425
iTrader: (2)

I see guide supports listed for the rear shocks on real.oem. Anything for the front?
jacobsed is offline  
0
Reply With Quote
      04-22-2013, 10:35 AM   #4
ellipsis212
I bought my ski mask in Aspen
 
ellipsis212's Avatar
 
Drives: MB 330i 6MT
Join Date: Jun 2009
Location: NYC > RVA

Posts: 965
iTrader: (4)

Garage List
2006 330i  [0.00]
If you want to make the job easier you should have a set of pass-through sockets. See the DIY. Also, when doing the front remove the whole strut by releasing the knuckle instead of compressing the spring while the strut is still inside. Once again, the DIY (toward the end) has info on that.

ECS tuning has a great walk-through video on their site and they do it the correct way. Good luck.
ellipsis212 is offline  
0
Reply With Quote
      04-22-2013, 05:30 PM   #5
jacobsed
Lieutenant
 
Drives: 2006 330xi
Join Date: Feb 2012
Location: United States

Posts: 425
iTrader: (2)

Not sure if dropping the knuckle will work on an xi since the drive shaft goes through the hub. It might not allow enough drop for the strut to clear the fender. All the DYI's I found are for RWD only.

I thought I could use two box end wrenches and didn't need a pass through socket?
jacobsed is offline  
0
Reply With Quote
      04-22-2013, 09:43 PM   #6
jacobsed
Lieutenant
 
Drives: 2006 330xi
Join Date: Feb 2012
Location: United States

Posts: 425
iTrader: (2)

Do the lower rear shock mounts normally need replacing?
jacobsed is offline  
0
Reply With Quote
      04-22-2013, 10:26 PM   #7
jacobsed
Lieutenant
 
Drives: 2006 330xi
Join Date: Feb 2012
Location: United States

Posts: 425
iTrader: (2)

Do the front bump stops require replacing? I've seen a couple notes for new struts that say they are absolutely required
jacobsed is offline  
0
Reply With Quote
      04-24-2013, 12:25 PM   #8
mike-y
just another bmw douche bag
 
Drives: 1.9L of fury
Join Date: Nov 2008
Location: Los Angeles, CA

Posts: 3,396
iTrader: (4)

Quote:
Originally Posted by jacobsed View Post
I see guide supports listed for the rear shocks on real.oem. Anything for the front?
the ones I was talking about are for the front. They are at the very top part of the front strut system where the 3 nuts bolt thru the strut tower. They look like a cup with a bearing at the bottom, and 3 bolts sticking up at the upper lip
mike-y is offline   United_States
0
Reply With Quote
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 07:25 PM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST