E90Post
 


 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Powertrain and Drivetrain Discussions > N54 Turbo Engine / Drivetrain / Exhaust Modifications - 335i > Help converting CM flowsensor to AQM with CMGS



Reply
 
Thread Tools Search this Thread
      07-29-2013, 10:38 AM   #1
ZTZ1010
Captain Planet
ZTZ1010's Avatar
United_States
23
Rep
1,062
Posts

 
Drives: 11' E92 ZCP M3
Join Date: Feb 2008
Location: CT

iTrader: (8)

Garage List
2009 BMW 335i  [4.80]
2011 BMW M3  [0.00]
Send a message via AIM to ZTZ1010
Help converting CM flowsensor to AQM with CMGS

Hi all -

I've seen a few others who prefer a turbine based safety running the same setup so I was hoping someone could lend some advice...

I'm trying to convert my system (CM flow sensor is shitting the bed causing plenty of boost fluctuations), but I'm no expert with wiring. I had a friend set up the system initially and it's worked like a charm... What is the easiest way to wire the AQM HE505 sensor into the JB4 to still maintain use of the CMGS controller? I've seen plenty of threads with people talking about doing the same for use with Procede, but none for JB4 even though I know a few people are running similar setups. I also DO NOT want to switch to a voltage based safety such as a FSB.


I was hoping to reuse the existing wires from my current CM flow sensor so as I didn't have to reroute everything behind trim and through the cabin/firewall. Any input would be greatly appreciated + apologies in advance for not being technically savvy when it comes to wiring...

Zach
__________________
2011.5 Alpine White E92 M3 | DCT w/ BPM Software | ZCP | CF Roof | CF Lip| Fully Coded | AFE Stage 2 Intake| ACM Exhaust | ACM Test Pipes | BPM Stage II Dev Tune | AA Pulleys | RPi Scoops | Swift Springs | LED Interior Lights| LUX V4 | Extended Aluminum DCT Paddles|
Appreciate 0
      07-29-2013, 11:57 AM   #2
enrita
Major General
enrita's Avatar
Sweden
92
Rep
7,331
Posts

 
Drives: 335i - Big turbos
Join Date: Sep 2008
Location: Italian in Sweden

iTrader: (0)

if you follow my advice and mail howerton engineering you will get the right answer. you need to hook the jb4 directly to the aquamist unit to run map 3. Both Terry and Howerton knows how to set it up.
__________________
07 335i AT - TD St.2 Turbos - COBB (Custom Cobb mapping by http://www.protuningfreaks.com/) - JB4G5 ISO - Okada Coils - NGK 5992 Plugs - E85 Walbro - Injen Intake - Helix IC - Snow Stg. 3 - Stett CP - AR DPs - midpipes 100 HJS Cats - Bastuck Quad - PSS10 - QUAIFE LSD - BMS OCC - Forge DVs - AR OC - ALCON BBK - M3 Chassi - Dinan CP - Velocity M rear Toe arms - Advan RZ-DF - Level 10 AT upgrade - Alpina AT Flash
Appreciate 0
      07-29-2013, 12:03 PM   #3
enrita
Major General
enrita's Avatar
Sweden
92
Rep
7,331
Posts

 
Drives: 335i - Big turbos
Join Date: Sep 2008
Location: Italian in Sweden

iTrader: (0)

some info i found in my mail box
The output id .5V in standby, and 4.5V full scale. The flow map with the green wire hooked to 12v will give you the biggest range, about 1500cc at 4.5V. The other two maps have smaller flow rates that hit 4.5V faster.
The green wire changes the mapping of the .5 to 4.5v signal coming out of the flow sensor. If you ground the green wire, it will be on the most sensitive map. Leaving the green wire un-connected will enable the middle map. Connecting the green wire to 12v, will enable the highest flow map, which should be about 4.5V for 1500cc.
__________________
07 335i AT - TD St.2 Turbos - COBB (Custom Cobb mapping by http://www.protuningfreaks.com/) - JB4G5 ISO - Okada Coils - NGK 5992 Plugs - E85 Walbro - Injen Intake - Helix IC - Snow Stg. 3 - Stett CP - AR DPs - midpipes 100 HJS Cats - Bastuck Quad - PSS10 - QUAIFE LSD - BMS OCC - Forge DVs - AR OC - ALCON BBK - M3 Chassi - Dinan CP - Velocity M rear Toe arms - Advan RZ-DF - Level 10 AT upgrade - Alpina AT Flash
Appreciate 0
      07-29-2013, 08:29 PM   #4
ZTZ1010
Captain Planet
ZTZ1010's Avatar
United_States
23
Rep
1,062
Posts

 
Drives: 11' E92 ZCP M3
Join Date: Feb 2008
Location: CT

iTrader: (8)

Garage List
2009 BMW 335i  [4.80]
2011 BMW M3  [0.00]
Send a message via AIM to ZTZ1010
got it sorted today... thanks Enrita
__________________
2011.5 Alpine White E92 M3 | DCT w/ BPM Software | ZCP | CF Roof | CF Lip| Fully Coded | AFE Stage 2 Intake| ACM Exhaust | ACM Test Pipes | BPM Stage II Dev Tune | AA Pulleys | RPi Scoops | Swift Springs | LED Interior Lights| LUX V4 | Extended Aluminum DCT Paddles|
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 11:56 PM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST