E90Post
 


ECS BMW
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > ConnectedDrive / I-Drive / Navigation Related Discussion > Successful Rear View camera retrofit by Bimmer Retrofit - review



Reply
 
Thread Tools Search this Thread
      08-22-2013, 01:48 PM   #1
Franky2ko
New Member
 
Drives: E92
Join Date: Jun 2013
Location: West Hollywood, CA

Posts: 9
iTrader: (0)

Successful Rear View camera retrofit by Bimmer Retrofit - review

I wanted to do this review for quite some time now, but never got to it until now. For a while I wanted to install a rear-view camera in my 2009 E92, because in a coupe it can sometimes be difficult to see what's going on in the back, and I wanted to avoid accidents, dents and scratches as much possible, and the rear-view camera is a great prevention against all that (especially because I let my gf take the car sometimes )

I had a few options to chose from, but decided to go with Bimmer Retrofit (one of the vendors here, www.bimmerretrofit.com). There were a few things that were important to me and Bimmer Retrofit met all that criteria:


1. Complete integration with iDrive - this was an absolute must for me. Although the camera is not OEM, it was important for me that it functions like OEM.

2. Easy installation - I am DIY guy and wanted to do the installation myself.

3. Single supplier - it was important for me to get everything, the camera, activation and coding from one place. I want to always deal with the same supplier for everything, especially when it comes to expensive things, like BMW. Only then you can achieve accountability.

4. What really won me over is fantastic customer service and quick delivery!

5. A nice bonus: programmable activation module. I am thinking of getting a 4-door and being able to keep the retrofit without any additional activation modules is definitely a PLUS.


Now about the installation itself:

Installation took me about 2.5 hrs. The key to a successful installation is deciding on two things:


1. Start from the back and work your way to the front or the other way around;

2. Pass the wires on the left side or the right side of the vehicle.


1. I found it easier to start at the front and work my way to the back. I can't really explain why I chose this option, but it was my gut feeling. So what I did is I started by remove all the plastic trim around the CIC, so I can plug in the PNP activation module.


The easiest way to install the PNP module is behind and to the right of the CIC. There is a fairly large gap and PNP modules fits right in.





2. Once the PNP cable is in, you should secure the wires using tie wraps, to make sure everything is solid and will not move during driving.


3. Once the PNP module is in, you should decide whether to pass the wiring along the left or right rocker panel. The wire supplied by Bimmer Retrofit is long enough to go either way, but my personal preference was to go on the left side. Why? I found it much easier to remove the plastic trim below the steering wheel, rather than remove plastic trim around the glovebox compartment and pass the wires through the glovebox.


4. Once the plastic trim below the steering wheel is removed, you can easily pass the cable below the steering wheel and all the way to the side to the rocker panel. I do not have any pictures of this because it was dark and the camera couldn't focus.


5. Once you get the cable to the rocker panel, you need to apply gentle pressure on the plastic trim that covers the rocker panel to remove the plastic trim. The plastic trim stays in place using plastic clips, and these clips will most likely stay in the rocker panel, once you remove the trim. You will need to remove them and place them back in the plastic trim, as shown in the picture.





6. You will then need to tuck in the wire, so that the plastic trim can safely be reinstalled.





7. You will then need to fold down the rear seats and to remove the "corner seat" (not sure what the proper name for this part is), but please refer to the pic below.


8. Once this is done you need to tuck in the wire between the seat and the side of the vehicle, to get to the corner. (I've got a two-door).





9. Then, you need to tuck in the wire behind the rear seat and get to the opposite side of the vehicle.


10. Then you just need to pass the wire to right side of the trunk. I did this behind the decorative lining on the right side of the vehicle.





11. The blue wires need to go to the back-up light. You need to connect the wires to the backup light. This is easily done using a “splicer”, supplied by Bimmer Retrofit.


12. The thicker black cable needs to go to the trunk handle. I passed it through the rubber “tunnel”.


13. And this is almost it. Just remove the existing handle, and insert the one with the camera built in. Bimmer Retrofit has a good instruction for this part. Now just connect the cables and that’s all.





The next step is to book an appointment with Bimmer Retrofit for coding of the rear-view camera. I did my coding session with Chris. He is extremely knowledgeable and fast. He finished the coding in less than 30 minutes and everything worked like magic.


Highly recommend this retrofit and I hope my mini-DIY will help you in the installation process.


Good luck!
Franky2ko is offline  
0
Reply With Quote
      09-04-2013, 08:33 AM   #2
stevers314
packet jockey
 
stevers314's Avatar
 
Drives: 2011 335d M Sport
Join Date: Jul 2013
Location: Lex

Posts: 193
iTrader: (0)

Garage List
2011 335d  [0.00]
Great information here. I am considering the same kit for my car, hope to buy it from them in the coming months.
__________________
2011 335d
With great torque comes great responsibility
stevers314 is offline  
0
Reply With Quote
      09-10-2013, 03:48 PM   #3
j23a45m
First Lieutenant
 
j23a45m's Avatar
 
Drives: 2011 E90 335
Join Date: Aug 2013
Location: Lancaster, Pa

Posts: 334
iTrader: (4)

Garage List
looks great
__________________
2011 BSM 335i E90 MTECH 6MT • JB4 stage 2 iso 5.3 • BMS Intake • Vishnu DP • Cyba Scoops • LUX V4 • 6000K Headlight/Fog light Morimoto • Euro headlight switch • ACS roof wing • 35% tint • Black Grilles • Misc coding • AA charge pipe • ///M3 fenders • 335is pedals • Bmw Performance spoiler •
j23a45m is offline   United_States
0
Reply With Quote
      01-29-2014, 10:23 PM   #4
compdr59
New Member
 
Drives: 2011 328xi
Join Date: Sep 2013
Location: Long Island, NY

Posts: 25
iTrader: (0)

Thanks for the post. I installed mine over the weekend. I went to the right but I couldn't remove the glovebox. The wire going to the trunk couldn't fit through the rubber tunnel. The enclosed instructions were not as good as yours. The one I purchased is self coding and doesn't require a connection to the backup lights.
compdr59 is offline  
0
Reply With Quote
      01-30-2014, 05:57 AM   #5
ashmostro
Lieutenant Colonel
 
ashmostro's Avatar
 
Drives: '13 335is DCT
Join Date: Jan 2013
Location: Vienna, VA

Posts: 1,519
iTrader: (7)

Nice post. Pics of the screen in action?
ashmostro is offline   United_States
0
Reply With Quote
      02-24-2014, 04:17 PM   #6
Franky2ko
New Member
 
Drives: E92
Join Date: Jun 2013
Location: West Hollywood, CA

Posts: 9
iTrader: (0)

Quote:
Originally Posted by ashmostro View Post
Nice post. Pics of the screen in action?
Ok sure. I'll try to get it done soon and will post a video here.
Franky2ko is offline  
0
Reply With Quote
      02-25-2014, 07:15 PM   #7
Raubtier
New Member
 
Drives: 2011 335is
Join Date: Dec 2013
Location: CA

Posts: 8
iTrader: (0)

Quote:
Originally Posted by compdr59 View Post
Thanks for the post. I installed mine over the weekend. I went to the right but I couldn't remove the glovebox. The wire going to the trunk couldn't fit through the rubber tunnel. The enclosed instructions were not as good as yours. The one I purchased is self coding and doesn't require a connection to the backup lights.
Compdr59, did you have to do any software updates to your iDrive before the installation or it was just plug n play?
Raubtier is offline  
0
Reply With Quote
      03-20-2014, 06:53 PM   #8
compdr59
New Member
 
Drives: 2011 328xi
Join Date: Sep 2013
Location: Long Island, NY

Posts: 25
iTrader: (0)

Quote:
Originally Posted by Raubtier View Post
Compdr59, did you have to do any software updates to your iDrive before the installation or it was just plug n play?
It's just plug and play. It's self coding.
compdr59 is offline  
0
Reply With Quote
      03-25-2014, 07:56 PM   #9
compdr59
New Member
 
Drives: 2011 328xi
Join Date: Sep 2013
Location: Long Island, NY

Posts: 25
iTrader: (0)

I recommend not to purchase from Bimmer Retrofit. The camera works great, but their customer service is awful. The seal around the camera shifted while washing my car. I couldn't get it to stay in place, so I sealed it with silicon. Now they say I modified the camera portion and voided the warranty. They won't send me a $5 gasket to remedy the problem.
Attached Images
 
compdr59 is offline  
0
Reply With Quote
      04-03-2014, 03:13 AM   #10
kelmk
Enlisted Member
 
Drives: 2008 BMW M3 Convertible
Join Date: May 2009
Location: San Francisco

Posts: 30
iTrader: (0)

The replacement trunk latch is definitely not oem quality but I was able to get it fitted eventually. I actually had to revalue the switch which came off. The coding also didn't work and I'm currently awaiting bimmerretrofit to send me a fix.
kelmk is offline  
0
Reply With Quote
      04-28-2014, 10:15 PM   #11
bmwretrofit
BimmerPost Supporting Vendor

 
bmwretrofit's Avatar
 
Drives: BMW
Join Date: Nov 2010
Location: Canada

Posts: 603
iTrader: (0)

Quote:
Originally Posted by compdr59 View Post
I recommend not to purchase from Bimmer Retrofit. The camera works great, but their customer service is awful. The seal around the camera shifted while washing my car. I couldn't get it to stay in place, so I sealed it with silicon. Now they say I modified the camera portion and voided the warranty. They won't send me a $5 gasket to remedy the problem.
We stand behind our products and are prepared to repair/exchange products under warranty, if the product is defective, however product must be returned to us in the original condition, and we must be advised of the issue ASAP. If the customer damages the product in any way, we are not able to replace/repair products under warranty.

If there is an issue with the product, the customer must advise us ASAP, without attempting to repair the product on his own. If the customer damages the product, we are not able to replace the product for free.

If the product is damaged, the manufacturer (of the trunk handle with camera built in) will not accept the product under warranty, and we will need to pay for the replacement camera out of our own pocket. Expenses like this are not factored into the final price, since we expect that customers actually read and follow Terms and Conditions before purchasing.

Warranty terms are there for a reason, and it is the responsibility of the customer to follow those terms and to contact Bimmer Retrofit as soon as there is any issue with the product.

In this case though, it looks like the trunk handle was just not properly installed - the silicon cover is a removable part of the trunk handle and can easily be adjusted. But, again, we have no way of knowing whether the product was defective or not properly installed, since the customer never shipped the camera back to us for inspection.
bmwretrofit is offline   Canada
0
Reply With Quote
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 01:49 PM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST