E90Post
 


European Auto Source
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > DIY Guides > DIY Info: E92/3 Black & Silver Carbon Fiber Roundel Replacement



Comment
 
Tutorial Tools Search this Tutorial
DIY Info: E92/3 Black & Silver Carbon Fiber Roundel Replacement
Published by Kev
04-27-2008
DIY Info: E92/3 Black & Silver Carbon Fiber Roundel Replacement

I received the new carbon fiber roundels package from Ada (adamaster) by Express Mail from Taiwan. These come with two exterior roundels (front & rear), four wheel caps, and one interior roundel for the airbag. The package comes with the newer larger sized roundels (78mm) for the rear one.

Since there is an extensive DIY on how to do the front for the E90 and it's essentially the same in the E92, I'll skip over that. However, the rear one is a little tricky so I decided to write this DIY.

1. Get one of those plastic wedges for trim removal
2. Use a thin piece of plastic card and wedge it in between the paint surface and the emblem. I used my CPR card.
3. Wedge the plastic wedge in between the plastic card and the roundel, and pry as hard as you could. You'll notice a lot of resistance because the stupid emblem has adhesive back attaching it to the trunk.
4. Once you released the old roundel, turn it over and check and see if there's any rubber grommets stuck on the emblem. If there is, remove them and replace it on the trunk opening.
5. Now comes the trick part, if you compare the stock roundel to the CF one, you'll notice that the tabs on the back of the stock emblem is indeed bigger than the CF roundel. So, you'll need to order TWO of this 51-14-1-889-489-M9, your local dealership should stock these.
6. Insert these two tiny rubber grommets to the tabs on the CF roundel, then install the roundel over the two larger black rubber grommets on your trunk.

Now you are done with installing the trunk roundels.

Pics to follow of final results.
__________________
kev { divinum est sedate dolorem }
Tutorial Tools
  #1  
By McLuVan on 04-27-2008, 01:08 PM
nice post
but wrong thread
Reply With Quote
  #2  
By Yeahas on 04-27-2008, 01:21 PM
wow i was looking for this diy all over the place..
btw wrong section dude
Reply With Quote
  #3  
By ohten on 05-13-2008, 07:33 PM
Member reviews
Difficulty [ 1 = Difficult ]
20%20%20%
1
Cost [ 1 = Expensive ]
20%20%20%
1
DIY Clarity [ 1 = Not clear ]
20%20%20%
1
Average 20%
Reply With Quote
  #4  
By Soni on 05-16-2008, 10:12 PM
I ordered the same...but my problem is the original black rubber gormments will stop the new emblem sit flush to the trunk, because the new emblem tabs base doesn't have an indented area for the black rubber gormments to sit in...so my when I insert the tabs in all the way, I still have about 1mm space all around.
Reply With Quote
  #5  
By Kev on 05-17-2008, 11:24 AM
Hmm..... that's odd. Mine doesn't have any gaps after installation.
Reply With Quote
Comment

Bookmarks

Tutorial Tools Search this Tutorial
Search this Tutorial:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 08:07 AM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST