E90Post
 


European Auto Source
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > DIY Guides > Changing the battery



Reply
 
Thread Tools Search this Thread
      08-14-2009, 04:34 PM   #1
GeneralXception
New Member
13
Rep
8
Posts

Drives: 05 330i SE
Join Date: Aug 2009
Location: Birmingham

iTrader: (0)

Changing the battery

Quite a few guides show how to disconnect the negative terminal of the battery but I needed to replace the battery in my 330i and I couldn't find any guides that explained how to remove it so here we are.

I understand that for many people this procedure will be self explanatory but I was a little apprehensive so there may be others in the same boat.

Tools that you'll need:
10mm socket
(possibly) 13mm socket
wrench for above sockets
flat head screwdriver

Translations
Boot = Trunk
Bonnet = Hood

The battery I used in this guide is the BMW 70mah. Diesel engined e9x's will no doubt have a higher rating and they may be larger. Check the top of the existing battery to see what rating it has before ordering one.

A couple of warnings before you go any further. First of all, you do all of this at your own risk. You're messing around with the electrical system of your expensive BMW, if you fry something then you foot the bill. In other words I take no responsibility for your actions. Secondly, the battery is quite heavy and contains some pretty nasty stuff so take care lifting it.

One more thing, open your car before carrying out any of this procedure. Don't just work with the boot open just in case you accidentally close the boot whilst the battery is disconnected. If that does happen and the car doors are open you can either bump the car from the terminals under the bonnet or climb through the seats into the boot - the choice is yours

You can get access to the battery by opening a panel on the right hand side of the boot. Turn the black plastic knob anti-clockwise and it should allow you to pull the entire section out.



Once opened you'll be presented with something like this:



What you're looking at is a protection bar that runs over the top of the battery to keep it in place if you roll the car. The large rectangular black plastic underneath the bar is is a safety device which can cut the connection to the positive terminal if an airbag is deployed. There's the negative terminal on the right hand side with a support to the right of the terminal and finally the big white thing is the battery

We need to remove the protection bar so use the 10mm socket and remove the two bolts that hold it in place. Remove the bar and bolts and put them somewhere safe.



There's another piece of plastic that holds the battery in place that you need to remove. I've highlighted the negative terminal (green) and the soft plastic (purple). Take the 10mm socket to the bolt that I've circled in purple and it should come undone fairly easy.



Take the bolt out and then remove the plastic piece and you'll have something like this.



Now you can remove the negative terminal. To do this you'll need that 10mm socket again to loosen the nut on the terminal. The thread on the bolt won't allow the nut to be removed completely (nice touch IMHO) so don't force it if it won't budge much after its been loosened.



Once you've loosened the terminal, remove it and place it where it can't touch the terminal again. Pushed down the side of the battery is fine where the soft plastic used to be. Just make sure that it can't pop back into place. Be mindful of this you really don't want it making its way back to the negative terminal.

Now the fun bit! The positive terminal is hidden away under that rectangle of black and red plastic. You can get to the terminal by flipping open the red plastic cover



This alone won't allow you to remove the terminal completely you also need to release that black plastic cover. To do that take a flat head screwdriver and place it into the lip and lift it away from the battery. This picture was taken after I'd removed it from the battery but the idea is the same.



Now the positive terminal is also disconnected you can remove the battery however it may be a bit tight with all those wires blocking the path.

To help you can separate the red terminal connector from the main black plastic cover. Lift up the flap and undo the nut with a 13mm socket.





This will split it into two halves. You can then remove the black wire that's linking the two halves by carefully pressing in the clip on the left hand side of the connector



Almost done! All you need to do now is remove the vent tube from the battery. Carefully pull it by the black plastic and it will come out.



You should now be able to remove the battery by lifting it by the two handles. Be careful, it's quite heavy.


Fitting the new battery

Fitting the new battery back in is just the reverse of the instructions, just make sure that you push the battery as far towards the front of the vehicle as possible.

One problem I had was putting the soft plastic back in place that fits next to the negative side of the battery. I found it easier to move the washer on the bottom of the bolt as high up the bolt as possible which keeps the bracket raised.



This is so I could see what I was doing and get the bolt into the hole. Once you've located it into the hole just tighten it enough to keep it upright and then squeeze the soft plastic between the bolt and the battery. Tighten up the bolt and check it's good and secure.

I won't go into detail for the remaining steps because the pictures above still apply. Here's what you need to do:

1. Fit the breather pipe, push it into the battery as far as it will go
2. Connect the positive terminal and tighten the bolt with a 10mm socket
3. If you split the terminal to allow easier access to the battery you can refit it now and don't forget to refit the black wire if you disconnected it.
4. Push down on the metal clips on the black plastic and they will click into place holding the cover down. Do this on both sides.
5. Refit the bar above the battery
6. Refit the negative terminal *

Start her up and set the clock. Job done. Well done

If you've any questions please reply to this thread instead of PM'ing me.

Thanks

Steve

* Some people say to switch on your lights before carrying out this step to prevent surges from the battery causing damage to components. I didn't do this and my car was fine. Besides I've got Xenons fitted and the surge may have damaged them instead so I never bothered

Last edited by GeneralXception; 03-07-2010 at 06:40 PM. Reason: Fixed missing images
Appreciate 0
      08-14-2009, 05:45 PM   #2
stressdoc
Moderator
stressdoc's Avatar
Dominica
253
Rep
10,343
Posts

Drives: F80 YMB
Join Date: Jun 2005
Location: MO

iTrader: (0)

Nice. Anyone with a Braille install that could at that or a link to this?
Appreciate 0
      08-17-2009, 04:24 PM   #3
FCP Euro
Lieutenant
FCP Euro's Avatar
United_States
5
Rep
464
Posts

Drives: Volvo 850 T5
Join Date: Aug 2009
Location: Old Saybrook, CT

iTrader: (0)

Nice write up. Pictures always make these jobs easier.
__________________

sales@fcpeuro.com
FCP Euro - European Car Parts Specialists
Appreciate 0
      08-30-2009, 06:14 PM   #4
rotaryboy
Private First Class
rotaryboy's Avatar
1
Rep
140
Posts

Drives: 330i 6MT
Join Date: Mar 2009
Location: Indiana

iTrader: (3)

Nice write up and pics.
Appreciate 0
      09-02-2009, 11:38 AM   #5
txusa03
Major General
204
Rep
6,567
Posts

Drives: TS330iPPSP6MT
Join Date: Jul 2005
Location: Planet Earth

iTrader: (3)

Nice DIY. I just recently had my bat replaced by dealer. Several months goes by and I find a funny looking washer in the trunk. Now I know where that washer should go. Lucky I did not throw it away.

Stealership service FTL!!!!
__________________
under construction!
Appreciate 0
      12-02-2009, 12:05 PM   #6
brunp
Private
Canada
5
Rep
79
Posts

Drives: 2006 BMW 325i,1998 BMW 328iS
Join Date: Feb 2009
Location: Ottawa, ON

iTrader: (0)

I don't have to do a replacement as of yet, but anyone know why some people are suggesting to go to the dealer to replace the battery. Some say, the car goes into safe mode and then you have to tell the computer that it has a new battery.

Can anyone confirm or deny this?

Paul
Appreciate 0
      12-06-2009, 11:14 AM   #7
ENINTY
Banned
75
Rep
3,415
Posts

Drives: 2006 325i Sport
Join Date: Jun 2006
Location: Virginia

iTrader: (0)

Quote:
Originally Posted by brunp View Post
I don't have to do a replacement as of yet, but anyone know why some people are suggesting to go to the dealer to replace the battery. Some say, the car goes into safe mode and then you have to tell the computer that it has a new battery.

Can anyone confirm or deny this?

Paul
It is true. The car monitors the condition of the battery as it ages to adjust the charging cycle. The procedure calls for resetting the battery condition monitor to tell the car's computer there is a new battery in place.

The BT scan tool should probably be able to reset the battery condition monitor. I've just ordered mine and when I get it I will check the software to see if it does. Going to the dealer to replace the battery is expensive, and the BT scan tool at $280 for the enthusiast version should well cover the cost savings by DIY vs. the dealer install. I'm using it as an excuse to buy the BT Scan tool. (although I bought the pro version…)
Appreciate 0
      12-06-2009, 01:02 PM   #8
brunp
Private
Canada
5
Rep
79
Posts

Drives: 2006 BMW 325i,1998 BMW 328iS
Join Date: Feb 2009
Location: Ottawa, ON

iTrader: (0)

Quote:
Originally Posted by ENINTY View Post
It is true. The car monitors the condition of the battery as it ages to adjust the charging cycle. The procedure calls for resetting the battery condition monitor to tell the car's computer there is a new battery in place.

The BT scan tool should probably be able to reset the battery condition monitor. I've just ordered mine and when I get it I will check the software to see if it does. Going to the dealer to replace the battery is expensive, and the BT scan tool at $280 for the enthusiast version should well cover the cost savings by DIY vs. the dealer install. I'm using it as an excuse to buy the BT Scan tool. (although I bought the pro version…)
This is good know. If you can confirm this, then I may purchase this kit to use on my car. I don't think I can justify the pro kit since all I would need is to use it on my car. :-)

Could be a birthday gift for this coming Feb., however, I think it may be useful for other purposes too. :-)

Paul
Appreciate 0
      12-08-2009, 02:24 PM   #9
revlimit
Second Lieutenant
5
Rep
247
Posts

Drives: E92 335i Le Mans Blue
Join Date: Mar 2005
Location: Los Angeles

iTrader: (5)

Quote:
Originally Posted by ENINTY View Post
It is true. The car monitors the condition of the battery as it ages to adjust the charging cycle. The procedure calls for resetting the battery condition monitor to tell the car's computer there is a new battery in place.

The BT scan tool should probably be able to reset the battery condition monitor. I've just ordered mine and when I get it I will check the software to see if it does. Going to the dealer to replace the battery is expensive, and the BT scan tool at $280 for the enthusiast version should well cover the cost savings by DIY vs. the dealer install. I'm using it as an excuse to buy the BT Scan tool. (although I bought the pro version…)
Where did you get your scan tool from? Did it work?
Appreciate 0
      12-10-2009, 12:47 AM   #10
froman
Private First Class
5
Rep
178
Posts

Drives: 2008 550i Sport Space Gray
Join Date: Jun 2006
Location: Houston, TX

iTrader: (0)

Quote:
Originally Posted by brunp View Post
I don't have to do a replacement as of yet, but anyone know why some people are suggesting to go to the dealer to replace the battery. Some say, the car goes into safe mode and then you have to tell the computer that it has a new battery.

Can anyone confirm or deny this?

Paul
Not true. I had to replace my battery while coming home from a trip to Kansas. The dudes at the WalMart in McAlester, Oklahoma replaced the battery and I was on my way again. It did take them a while to get all that crap disconnected from the battery, though!
Appreciate 0
      12-10-2009, 02:24 AM   #11
revlimit
Second Lieutenant
5
Rep
247
Posts

Drives: E92 335i Le Mans Blue
Join Date: Mar 2005
Location: Los Angeles

iTrader: (5)

Quote:
Originally Posted by froman View Post
Not true. I had to replace my battery while coming home from a trip to Kansas. The dudes at the WalMart in McAlester, Oklahoma replaced the battery and I was on my way again. It did take them a while to get all that crap disconnected from the battery, though!

How long ago has it been since you replaced your battery? Any starting issues? Have you tried measuring the voltage to see if it dropped?
Appreciate 0
      12-10-2009, 04:51 PM   #12
mds82
Major General
mds82's Avatar
154
Rep
5,844
Posts

Drives: 2006 325xi
Join Date: Aug 2005
Location: South Central Connecticut

iTrader: (40)

Garage List
Send a message via AIM to mds82 Send a message via Yahoo to mds82
So i replaced mine last night - Very good instructions, clear and exact..

There is 1 thing listed however. In the picture below, there is a 2 wire cable that is wrapped up. This cable does NOT go anywhere - it does not connect to anything. When i was done - i had 1 extra wire and could not figure out where it does. It just sits there and has no purpose
Attached Images
 
Appreciate 0
      12-11-2009, 11:10 PM   #13
ENINTY
Banned
75
Rep
3,415
Posts

Drives: 2006 325i Sport
Join Date: Jun 2006
Location: Virginia

iTrader: (0)

Quote:
Originally Posted by froman View Post
Not true. I had to replace my battery while coming home from a trip to Kansas. The dudes at the WalMart in McAlester, Oklahoma replaced the battery and I was on my way again. It did take them a while to get all that crap disconnected from the battery, though!
Both the Bently service manual and the BMW TIS call for resetting the computer when the battery is replaced. You can replace the battery and not reset the computer, but the car will not properly charge the new battery. I'm sure the dudes at walmart in McAlester, OK know better than the BMW TIS and Bently publishing that as been developing BMW repair manuals since the 1980's based on actual repair of BMWs.
Appreciate 0
      12-14-2009, 03:02 PM   #14
sherlock
New Member
0
Rep
23
Posts

Drives: 2006 325i
Join Date: Nov 2009
Location: Berlin, NJ USA

iTrader: (0)

An easy way to keep any battery cable from accidentally touching the battery terminal is to place a plastic sandwich bag over the cable end and secure it with tape or a rubber band. Just thought I'd pass this on....
Appreciate 0
      12-15-2009, 01:48 AM   #15
yamazaho
Wang D.D.S.
yamazaho's Avatar
Taiwan
111
Rep
7,061
Posts

Drives: 14' WRX, 15' W205
Join Date: Jul 2006
Location: Houston, TX

iTrader: (11)

Garage List
2006 325i  [3.88]
Send a message via Skype™ to yamazaho
Nice write up, I am glad someone posted this since I think I will need a new battery soon. My car seems to have a hard time starting up recently, did you guys replace with OEM batteries????
__________________
Appreciate 0
      12-16-2009, 06:38 PM   #16
Vasil
Private First Class
Vasil's Avatar
United_States
5
Rep
180
Posts

Drives: M3, M5 and 330i
Join Date: Apr 2006
Location: USA

iTrader: (11)

FYI: Since there has been a lot of talk about the importance of registering the battery, I wanted to point that my dealer charges only 0.5h of labor to register the battery.
Appreciate 0
      12-18-2009, 02:38 PM   #17
uncle ben
Private First Class
uncle ben's Avatar
Canada
2
Rep
111
Posts

Drives: 06 330i
Join Date: Nov 2009
Location: Edmonton

iTrader: (0)

great post! very clear pictures and easy explanation. Thanks for great DIY!
Appreciate 0
      12-19-2009, 04:39 PM   #18
revlimit
Second Lieutenant
5
Rep
247
Posts

Drives: E92 335i Le Mans Blue
Join Date: Mar 2005
Location: Los Angeles

iTrader: (5)

Quote:
Originally Posted by Vasil View Post
FYI: Since there has been a lot of talk about the importance of registering the battery, I wanted to point that my dealer charges only 0.5h of labor to register the battery.
How much will that be?
Appreciate 0
      12-21-2009, 07:22 PM   #19
RioGrandeValley
Major
RioGrandeValley's Avatar
21
Rep
1,025
Posts

Drives: E92/E90 Depends on Mood
Join Date: Mar 2009
Location: Irving, TX

iTrader: (1)

FYI my battery went out at 60K or so on my 06 E90. Same for coworker's 06 E90, same for other friend's 06 E90 especially with cold weather. I took mine to BMW of Dallas charged me $525 with a $25 discount...better than $550 i guess. My coworker drove his to the local Autozone where he ended up buying one from them then they installed for free. He didn't have to reset anything nor did his car give any error codes afterwards. Now another friend of mine needs his battery replaced today YUP another 06 E90 but lucky his is at 91K miles. Reading this Mike??? Later guys just my .02 cents
Appreciate 0
      12-21-2009, 07:50 PM   #20
.retired.
.retired.'s Avatar
United_States
24
Rep
934
Posts

Drives: E90
Join Date: Aug 2009
Location: Dallas Ft. Worth

iTrader: (1)

Quote:
Originally Posted by RioGrandeValley View Post
FYI my battery went out at 60K or so on my 06 E90. Same for coworker's 06 E90, same for other friend's 06 E90 especially with cold weather. I took mine to BMW of Dallas charged me $525 with a $25 discount...better than $550 i guess. My coworker drove his to the local Autozone where he ended up buying one from them then they installed for free. He didn't have to reset anything nor did his car give any error codes afterwards. Now another friend of mine needs his battery replaced today YUP another 06 E90 but lucky his is at 91K miles. Reading this Mike??? Later guys just my .02 cents

got it C
will be on this tonight and hopefully will be able to get the new battery in tomorrow and running. car driving now has expired tags so can't wait any longer
Appreciate 0
      12-22-2009, 10:35 AM   #21
brunp
Private
Canada
5
Rep
79
Posts

Drives: 2006 BMW 325i,1998 BMW 328iS
Join Date: Feb 2009
Location: Ottawa, ON

iTrader: (0)

Quote:
Originally Posted by RioGrandeValley View Post
FYI my battery went out at 60K or so on my 06 E90. Same for coworker's 06 E90, same for other friend's 06 E90 especially with cold weather. I took mine to BMW of Dallas charged me $525 with a $25 discount...better than $550 i guess. My coworker drove his to the local Autozone where he ended up buying one from them then they installed for free. He didn't have to reset anything nor did his car give any error codes afterwards. Now another friend of mine needs his battery replaced today YUP another 06 E90 but lucky his is at 91K miles. Reading this Mike??? Later guys just my .02 cents
"cold weather" in Texas....you got to be kidding me....
Appreciate 0
      12-24-2009, 07:32 PM   #22
scottp999
Brigadier General
scottp999's Avatar
77
Rep
4,754
Posts

Drives: 335i - E92 - 6MT & 4runner SR5
Join Date: Mar 2007
Location: MD

iTrader: (2)

Garage List
2007 BMW 335  [4.50]
You can reset the battery adaption with the Bav Tec tool (even with the enthusiast version). My replacement battery (lightweight) worked for a couple weeks and then I began getting the low battery light because the car was under-charging it. I needed to reset the battery adaption. To do this with the BT tool:

Engine Module, Commands, Battery Replacement Adaption, Click Send Button.
__________________
Rob Beck Turbos, PROcede Rev. 3, Procede Fueling Flash (via OpenFlash Tablet), PPS Methanol System (Devil's Own 12 GPH Nozzle/Aquamist Flow Sensor/Labonte VC25), DCI, Quaife LSD, BMW Performance Suspension, Autobahn Exotics Exhaust, Helix FMIC, AR Design Downpipes, BSH Catch Can, RB PCV Valve, Forge Diverter Valves, P3cars Vent Boost Gauge, Alufelgen CSL Reps, Lux 5.1 H8 Angel Eyes, HPB HID Fogs, LTBMW M3 Side Skirts, BMW M3 Rear Spoiler, BMW Front Aero Lip, BMW Pedal Kit, BMW M Shift Knob, Autotecknic Matte Black Grilles.
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 12:48 AM.




e90post
e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2016, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST