E90Post
 


Lux Angel Eyes
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > DIY Guides > DIY: Body Colour Finisher Rods



Comment
 
Tutorial Tools Search this Tutorial
DIY: Body Colour Finisher Rods
Published by nexus66
04-29-2007
DIY: Body Colour Finisher Rods

Instead of replacing my black plastic finisher rods with the silver ones, I decided to paint them body colour. I just bought some primer and colour matched aerosol spray paint from my local car store. No laquer/clear coat required for Jet Black - must be mixed with the paint already?!?!

First, remove the finisher rods from the car. The centre one comes off quite easily if you just push it up. The side ones are a pain, I hooked a right-angled pick and just pulled from the centre to the outside - didn't break any tabs - but took quite a lot of force!

Now you need to prep the pieces. You need to sand off the "grain" in the plastic for best results. Get a really smooth finish by using higher and higher grades of sandpaper.

Prep the area where you are going to paint. I used a cardboard box, and make a frame to hold the parts from polystyrene and a couple of screws. This way I could cover it all while the paint dried without any dust settling on the finish.

Clean the parts using either a tack-rag or a cloth with thinners/white spirit and place on your frame. It is a good idea to be wearing rubber gloves to stop any grease from your fingers contaminating the parts.

Now give the parts a few light coats of primer. I did about 4 coats in the one night, leaving approx 10 mins between coats. Leave to dry until the next night!

Ok, now we can paint! Firstly, give the primer coat a very light wet sand using at least 1200 grit wet/dry sandpaper. Then clean again! Again gloves are a good idea. Once dry and ready for painting give them a couple of very light coats and leave to dry overnight.

Repeat the light wet sand, and paint again. Leave overnight...

I repeated the wet sand/paint again - see how you go and how good your finish looks!

Finally once they were dry, they can be re-fitted onto the car! A very subtle mod on a black car, but the black plastic just annoyed me.

Pics below...
__________________

Drives: BMW E90 325iSE
Jet Black - 160 Wheels - CF Splitters
Manual - Sports Seats - Anthracite
Tutorial Tools
Attached Images
       
  #1  
By abc9475 on 04-29-2007, 03:51 PM
Looks better
Reply With Quote
  #2  
By BoostedBMW on 04-29-2007, 03:53 PM
It looks much cleaner now, nice job.
Reply With Quote
  #3  
By daveyg on 04-29-2007, 03:55 PM
Looks awesome now just black out the front grills.
Reply With Quote
  #4  
By j|rz44 on 04-29-2007, 04:11 PM
Nice!
Reply With Quote
  #5  
By Not Ur Avg 3 on 04-29-2007, 05:49 PM
looks great bro
much more alive than the 325i's lower finishing black rods
ur paint gives the color a much more glossy look
overall,

btw, ur cf splitters look nice, and fyi, CF lower finishing rods are forsale by some vendor, cant rmr who, but that too wud be a good match with ur splitters. maybe a cf grill as well to go along with ur theme?
Reply With Quote
  #6  
By FrankoQ on 04-29-2007, 08:43 PM
Nice!!!
Reply With Quote
  #7  
By ironic on 04-29-2007, 09:06 PM
wow very smart w/ the styrofoam
Reply With Quote
  #8  
By Chesmu on 04-29-2007, 09:24 PM
very nice. I bought black rods on crown autoparts and replaced my "silver" ones. Looks greats.
Reply With Quote
  #9  
By nexus66 on 04-30-2007, 02:06 AM
Quote:
Originally Posted by daveyg View Post
Looks awesome now just black out the front grills.
Do you mean spray them too?? Not a bad idea... Anyone done this??
Reply With Quote
  #10  
By nexus66 on 04-30-2007, 02:15 AM
And here's some pictures with the rods removed...
Attached Images
   
Reply With Quote
  #11  
By Josh49 on 04-30-2007, 08:02 AM
Nicely done..
Reply With Quote
  #12  
By Kiemyster on 04-30-2007, 09:01 AM
hmm i think this would only work on a black car. any other color might be... a bit off.
Reply With Quote
  #13  
By BigO1120 on 04-30-2007, 09:05 AM
I think it would look good regardless of the car's color. I'm thinking of doing this on my Montego Blue E90.
Reply With Quote
  #14  
By Kiemyster on 04-30-2007, 09:24 AM
hmm. well maybe. id have to see it. i want to see it in alpine white.
Reply With Quote
  #15  
By BigO1120 on 04-30-2007, 09:27 AM
That one would definitely look HOT!!!

Good mod nexus66!!!
Reply With Quote
  #16  
By ZuerstBMW on 04-30-2007, 09:55 AM
Quote:
Originally Posted by Chesmu View Post
very nice. I bought black rods on crown autoparts and replaced my "silver" ones. Looks greats.
Thats funny, I did the opposite. We could have traded. My cars silver , so the silvers ones look better, but the black definitely look better on the black, nice job.
Reply With Quote
  #17  
By Geoff on 04-30-2007, 03:27 PM
looks good to me
Reply With Quote
  #18  
By E90330iS on 04-30-2007, 05:45 PM
Looks great!
Reply With Quote
  #19  
By ska///235i on 05-01-2007, 06:13 PM
WOW you didnt break any of the taps off....Awesome

Nice DIY
Reply With Quote
  #20  
By Jason on 05-03-2007, 09:16 PM
Added to DIY master list - http://www.e90post.com/forums/showthread.php?t=1721

Thanks for sharing.
Reply With Quote
  #21  
By lb_335i on 05-10-2007, 02:45 PM
Looks good! Thats what I want to do to my silver rods.
Reply With Quote
Comment

Bookmarks

Tutorial Tools Search this Tutorial
Search this Tutorial:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 05:12 PM.




e90post
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST