335d experimenting new mods - BMW 3-Series (E90 E92) Forum

335dM · 07-13-2011, 09:44 PM

well i just installed my JBD today (set at 80%) and will be experimenting water injection( would like a kit with an electro-magnetic pump like Aquamist use to have) and adding a better aftermarket front mount intercooler and piping.
any suggestion would be appreciated since i dont know yet if 335i i/c would fit with little mod.
I have looked into 2 brand of water injection kit : cooling mist or Aquamist

My goal is to hit 400hp from my diesel engine while keeping a strong reliability by only cooling intake charges and better flowing

taibanl · 07-13-2011, 09:50 PM

Do you think the stock engine does not generate enough compression?

335dM · 07-13-2011, 09:59 PM

i just want to try to lower intake temp as much as i can and trying to burn better diesel for also better fuel economy. As i stated, i'm experimenting

335dM · 07-13-2011, 10:05 PM

water injection will allow higher boost pressures being run without detonation and high pressures.....increases torque. It’s all about torque

f00dstamps · 07-14-2011, 08:29 AM

Do you think our transmission can handle more torque than a JBD @ 100% (this is what I have mine set at) plus other mods?

Insider · 07-14-2011, 03:26 PM

I could be wrong, but I don't think anyone has hit 400hp on the diesel. You are going to need the gas version for that.

335dM · 07-14-2011, 06:53 PM

Quote:

Originally Posted by Insider

I could be wrong, but I don't think anyone has hit 400hp on the diesel. You are going to need the gas version for that.

Of course it is possible ! Just not done yet!

335dM · 07-14-2011, 06:56 PM

Quote:

Originally Posted by f00dstamps

Do you think our transmission can handle more torque than a JBD @ 100% (this is what I have mine set at) plus other mods?

The transmission is design to take over 540lbs of torque ! If u take good care of her without brake boost... Everything should be fine. This tranny if I'm correct comes from a v8 or v12 I don't remember to support higher torque numbers

335dM · 07-14-2011, 06:57 PM

Quote:

Originally Posted by 335dM

Quote:

Originally Posted by Insider

I could be wrong, but I don't think anyone has hit 400hp on the diesel. You are going to need the gas version for that.

Of course it is possible ! Just not done yet!

BMW 335d uses only 60% of it's potential

)

taibanl · 07-14-2011, 07:28 PM

Uh. Im pretty sure JBD @ 100% is within a single digit (ft-lbs) of the tranny torque limit. Good luck!

335dM · 07-14-2011, 09:13 PM

540 lbs is not the limit! It's a number that the tranny can hold before having a risk of failure! We are far from a tranny break down on the "D"

taibanl · 07-14-2011, 09:16 PM

..To each his own...

DieselDiner · 07-15-2011, 08:27 AM

Our cars have the ZF 6HP28 transmission, which is rated at 700Nm, or 516 ft/lbs. of torque. So we do have some room to go upwards from the factory rating of 425 ft./lbs., but do be careful!

Concentric190 · 07-15-2011, 02:14 PM

interested to see how far the D can be pushed

ChiDiddy · 07-16-2011, 01:43 AM

Dont think you see close to 400hp with w/m injection, FIC, and JBD...

need exhaust upgrades, further tuning, etc

335dM · 07-16-2011, 03:25 PM

Quote:

Originally Posted by ChiDiddy

Dont think you see close to 400hp with w/m injection, FIC, and JBD...

need exhaust upgrades, further tuning, etc

U are propably right but I will try anyway and only dyno's will tell

Thud · 08-05-2011, 12:50 PM

Quote:

Originally Posted by Insider

I could be wrong, but I don't think anyone has hit 400hp on the diesel. You are going to need the gas version for that.

Or propane.

Ron1n · 08-15-2011, 07:40 PM

Quote:

Originally Posted by Thud

Or propane.

This is what I'd like to do...

Auto · 09-21-2011, 01:44 AM

400hp/835nm+ has been done in Sweden!

http://dcsforum.se/dieselsnack/viewtopic.php?f=4&t=6238

http://www.garaget.org/?car=223177

Concentric190 · 09-21-2011, 08:03 AM

Sweden is always again of the F/I game.

DieselDiner · 09-21-2011, 08:44 AM

Quote:

Originally Posted by Auto

400hp/835nm+ has been done in Sweden!

http://dcsforum.se/dieselsnack/viewtopic.php?f=4&t=6238

http://www.garaget.org/?car=223177

Amazing. Not sure I would want to drop that much power on our tranny.

hotrod2448 · 09-21-2011, 12:18 PM

Swedish doesn't translate with google very well.

Quote:

Jahapp here, new gas project be set up
starting with a little half bad pictures better, What should be done one Folders 2 built downpipe and full-flow exhaust system, three possible flow preppa turbo eggs 4 ev preppa aut 5 My goal is Sweden's best 335d Coupe 2011

Where does one find these "turbo eggs"?

07-13-2011, 09:44 PM	#1
335dM Captain Drives: 335d m package Join Date: May 2011 Location: montreal Posts: 601 iTrader: (0)	335d experimenting new mods well i just installed my JBD today (set at 80%) and will be experimenting water injection( would like a kit with an electro-magnetic pump like Aquamist use to have) and adding a better aftermarket front mount intercooler and piping. any suggestion would be appreciated since i dont know yet if 335i i/c would fit with little mod. I have looked into 2 brand of water injection kit : cooling mist or Aquamist My goal is to hit 400hp from my diesel engine while keeping a strong reliability by only cooling intake charges and better flowing
	Tweet

07-14-2011, 03:26 PM	#6
Insider Captain Drives: 2007 335i Join Date: Jul 2006 Location: 4,500 feet above sea level Posts: 710 iTrader: (0)	I could be wrong, but I don't think anyone has hit 400hp on the diesel. You are going to need the gas version for that. __________________ http://www.insiderpicks.com - The world's best stock picks.

07-14-2011, 07:28 PM	#10
taibanl Colonel Drives: 2011 335d Join Date: Sep 2010 Location: Syracuse Posts: 2,649 iTrader: (4) Garage List 2011 335d [0.00]	Uh. Im pretty sure JBD @ 100% is within a single digit (ft-lbs) of the tranny torque limit. Good luck! __________________ WTB: 335is Black Chrome Tips -PM Me FS:Sub Amp - works w/ Technic harness! MRD-M300 FREE!!: Euro-Amber LCI LED tails (for repair) DON'T BUY FROM RAF555!!!! Ask me why

07-15-2011, 02:14 PM	#14
Concentric190 Second Lieutenant Drives: M3 turbo Join Date: Mar 2011 Location: Willowbrook, IL Posts: 251 iTrader: (0) Garage List 1997 BMW M3 [0.00] 2009 BMW 335d [0.00] 1995 BMW M3 [0.00]	interested to see how far the D can be pushed __________________ ///Andres 09 335d evolve tuned - 327whp / 490wtq -- 13.0@105 95 M3 Turbo - Built 3.0l s52, PTE74GTQ, AEM EMS & CDI

09-21-2011, 08:03 AM	#20
Concentric190 Second Lieutenant Drives: M3 turbo Join Date: Mar 2011 Location: Willowbrook, IL Posts: 251 iTrader: (0) Garage List 1997 BMW M3 [0.00] 2009 BMW 335d [0.00] 1995 BMW M3 [0.00]	Sweden is always again of the F/I game. __________________ ///Andres 09 335d evolve tuned - 327whp / 490wtq -- 13.0@105 95 M3 Turbo - Built 3.0l s52, PTE74GTQ, AEM EMS & CDI

07-13-2011, 09:50 PM	#2
taibanl Colonel Drives: 2011 335d Join Date: Sep 2010 Location: Syracuse Posts: 2,649 iTrader: (4) Garage List 2011 335d [0.00]	Do you think the stock engine does not generate enough compression?

07-13-2011, 09:59 PM	#3
335dM Captain Drives: 335d m package Join Date: May 2011 Location: montreal Posts: 601 iTrader: (0)	i just want to try to lower intake temp as much as i can and trying to burn better diesel for also better fuel economy. As i stated, i'm experimenting

07-13-2011, 10:05 PM	#4
335dM Captain Drives: 335d m package Join Date: May 2011 Location: montreal Posts: 601 iTrader: (0)	water injection will allow higher boost pressures being run without detonation and high pressures.....increases torque. It’s all about torque

07-14-2011, 08:29 AM	#5
f00dstamps Private First Class Drives: 2010 BMW 335d Join Date: Feb 2011 Location: US Posts: 125 iTrader: (0)	Do you think our transmission can handle more torque than a JBD @ 100% (this is what I have mine set at) plus other mods?

07-14-2011, 09:13 PM	#11
335dM Captain Drives: 335d m package Join Date: May 2011 Location: montreal Posts: 601 iTrader: (0)	540 lbs is not the limit! It's a number that the tranny can hold before having a risk of failure! We are far from a tranny break down on the "D"

07-14-2011, 09:16 PM	#12
taibanl Colonel Drives: 2011 335d Join Date: Sep 2010 Location: Syracuse Posts: 2,649 iTrader: (4) Garage List 2011 335d [0.00]	..To each his own...

07-15-2011, 08:27 AM	#13
DieselDiner Major Drives: 335d Join Date: Aug 2010 Location: Home Posts: 1,494 iTrader: (2)	Our cars have the ZF 6HP28 transmission, which is rated at 700Nm, or 516 ft/lbs. of torque. So we do have some room to go upwards from the factory rating of 425 ft./lbs., but do be careful!

07-16-2011, 01:43 AM	#15
ChiDiddy 50 Drives: Acura RSX, 335d, S281 Stang Join Date: Jan 2009 Location: Houston Posts: 142 iTrader: (0)	Dont think you see close to 400hp with w/m injection, FIC, and JBD... need exhaust upgrades, further tuning, etc

09-21-2011, 01:44 AM	#19
Auto Lieutenant Drives: Sold Join Date: Oct 2006 Location: Sweden Posts: 557 iTrader: (0)	400hp/835nm+ has been done in Sweden! http://dcsforum.se/dieselsnack/viewtopic.php?f=4&t=6238 http://www.garaget.org/?car=223177

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search