[Dinamita25]

I own a 2007 e90 335i and I love it but I have this error message that is driving me nuts!
A while back my headlight had condensation in it. I removed it and opened up the control module, sure enough it was fried.. I replaced the module, and at startup the headlights auto level and the passenger side headlight moves from side to side . The headlights only move at startup. A few seconds after start-up the malfunction message pops up. While driving, my headlights don't move like they did before. Worse of all the malfunction warning won't go away.. Any ideas??

[bmw325i]

Originally Posted by Dinamita25

I own a 2007 e90 335i and I love it but I have this error message that is driving me nuts!
A while back my headlight had condensation in it. I removed it and opened up the control module, sure enough it was fried.. I replaced the module, and at startup the headlights auto level and the passenger side headlight moves from side to side . The headlights only move at startup. A few seconds after start-up the malfunction message pops up and doesn't go away. While driving, my headlights don't move like they did before. Worse of all the malfunction warning won't go away.. Any ideas??

Reset lsmc and rsmc with ncsexpert.

[Dinamita25]

Originally Posted by bmw325i

Reset lsmc and rsmc with ncsexpert.

I'm assuming i need a cable and coding software? Does this cable look right? Thanks

http://m.ebay.com/itm/261212278917?nav=SEARCH&sbk=1

[bmw325i]

Originally Posted by Dinamita25

I'm assuming i need a cable and coding software? Does this cable look right? Thanks

http://m.ebay.com/itm/261212278917?nav=SEARCH&sbk=1

That's the cable I have, it works fine on my 06 which uses kcan. I'm not sure how it works on newer BMW's that use dcan.

[bmw325i]

Here's one from a U.S. seller. You wont have to wait weeks to get it.

http://m.ebay.com/itm/400628305284?nav=SEARCH&sbk=1

[Dinamita25]

Originally Posted by bmw325i

Here's one from a U.S. seller. You wont have to wait weeks to get it.

http://m.ebay.com/itm/400628305284?nav=SEARCH&sbk=1

Thanks alot. Do you think you can point in the right direction on how to reset what you mentioned?

[Dinamita25]

The cable says

E90,E91,E92,E93 od 03/2007..

Does that mean the cable wont be compatible with my car??

[bmw325i]

Originally Posted by Dinamita25

The cable says

E90,E91,E92,E93 od 03/2007..

Does that mean the cable wont be compatible with my car??

I'm not sure. I know the cheaper cables work fine for an 06. Most people use a more expensive cable for the newer models, but it says it works with dcan.

This one says it works with models up to 2012.
http://m.ebay.com/itm/111217830348?nav=SEARCH&sbk=1

[bmw325i]

Originally Posted by Dinamita25

Thanks alot. Do you think you can point in the right direction on how to reset what you mentioned?

Found this in another thread.

Originally Posted by acidbbg

This is the correct guide..Thanks for the confirmation BMW..

1. Load NCSExpert.
2. Load Profile and select Expertmode
3. F1 (VIN/ZCS/FA)
4. F3 (ZCS/FA f .ECU)
5. Choose E89 (for the E9X)
6. Select CAS
7. F6 (BACK)
8. F4 (Process ECU)
9. Select the Module I want to Revert back to Stock.
10. F2->Choose "SG_Codieren->ok
11. F3->to start coding the ecu with factory settings according to the vehicle VO.

Link to original thread.
http://www.e90post.com/forums/showthread.php?p=14357959