PROcede CANbus wiring update directions (video)

OpenFlash · 04-14-2009, 03:18 PM

Only for those who have NO CANbus wiring on their Rev.2 harness and received their CANbus wire pack update:

(it's in HD!)

Cheers,
Shiv

TMR · 04-14-2009, 03:20 PM

Works perfect. THANKS!!!!!!! Shiv, get in contact with me when you have a min.

Vudoo4u2 · 04-14-2009, 03:36 PM

hey man, do we have to entirely uninstall the harness when we do this? Or can I just keep it plugged in, but swap those two wires (assuming my battery is disconnected before I start, and the procede firmware has already been loaded up w/o a engine start up)

Tobias1980 · 04-14-2009, 03:37 PM

Nice Shiv! Do you have an ETA on new CANbus maps?

Dustin Bramell · 04-14-2009, 03:38 PM

You can just remove the grey sub-connector from the ECU connector. We just removed it for the sake of video clarity.

Quote:

Originally Posted by Vudoo4u2

hey man, do we have to entirely uninstall the harness when we do this? Or can I just keep it plugged in, but swap those two wires (assuming my battery is disconnected before I start, and the procede firmware has already been loaded up w/o a engine start up)

inthemiddle · 04-14-2009, 03:38 PM

Quote:

Originally Posted by Vudoo4u2

hey man, do we have to entirely uninstall the harness when we do this? Or can I just keep it plugged in, but swap those two wires (assuming my battery is disconnected before I start, and the procede firmware has already been loaded up w/o a engine start up)

To get the wires in the plugs, you have to pull them off the DME/ECU/whatever you want to call it....

Vudoo4u2 · 04-14-2009, 03:40 PM

thank you vm..psyched, I keep checking the mail for it!

Bluewater335i · 04-14-2009, 04:27 PM

Oops, I didn't see this post when posting this the first time...

Just to be clear, I haven't installed my procede rev ii, non-CANBUS harness because I was waiting on the CANBUS cables. Do I need to install the procede (non-CANBUS) in my car and upgrade the firmware BEFORE I install the CANBUS cable? -or is there a way to update the firmware without installing the procede in the car?

Thanks

rustyrotors · 04-14-2009, 05:50 PM

Quote:

Originally Posted by Dustin@Vishnu

You can just remove the grey sub-connector from the ECU connector. We just removed it for the sake of video clarity.

OK I'm confused. So, I remove the (procede) grey sub-connector from the (factory) ECU connector. Then, do I replace the factory grey sub-connector back into the ECU connector, and reconnect the ECU connector back into the ECU, in order to update the firmware?

Or, are you saying, that we just remove the procede grey sub-connector from the factory ECU connector and update the firmware, with essentally no grey factory subconnector connected to the ECU?

Kbueno · 04-14-2009, 06:05 PM

You guys are confusing me! Sounds like that you update the firmware with the PROcede installed, then turn off wait 15 min...come back and change out wires. Is this correct?

scalbert · 04-14-2009, 06:37 PM

Thanks, I'm gald I did not just send an email asking before checking the forum.

Dustin Bramell · 04-14-2009, 06:38 PM

It's very simple guys.

1. Update the firmware and map as you normally would.
2. Remove the grey connector, install the wires, and the replace the grey connector.

If you are confused about the process, please send me a PM. I think posting here is just causing more confusion.

thanks,
DB-

Vudoo4u2 · 04-14-2009, 06:51 PM

you plug in your key, but dont turn the engine over, just the power 1 click

update your firmware, turn off the car. unplug your battery, then do the swap of the canbus wire

scalbert · 04-14-2009, 06:51 PM

For those of use who would rather not reference the video, even though it is a cinematic masterpeice:

From wire side of PROcede connector, top right is terminal 1, release locking tabs on side

Pin 5 - Green/White, tab facing down
Pin 21 (below Pin5) - Blue/White

Grey DME Male Pin Connector

Pin 1 - Grren/White
Pin 14 - Blue/White

TMR · 04-14-2009, 09:26 PM

Quote:

Originally Posted by scalbert

For those of use who would rather not reference the video, even though it is a cinematic masterpeice:

From wire side of PROcede connector, top right is terminal 1, release locking tabs on side

Pin 5 - Green/White, tab facing down
Pin 21 (below Pin5) - Blue/White

Grey DME Male Pin Connector

Pin 1 - Grren/White
Pin 14 - Blue/White

Could have used that infor a week ago!!!! Thanks. Stage 1 feels really good. Not as strong as running Stage 3 on the previous map but i cant wait what the new stage 2 and stage 3 maps look like.

shawshank772 · 04-14-2009, 09:41 PM

WOW, honestly with 10 different people posting their own DIY on here its confusing. Simply follow the video step by step and you will be FINE

I watched a couple people do it and it doesnt seem hard.

scalbert · 04-15-2009, 08:07 AM

Quote:

Originally Posted by TMR

Could have used that infor a week ago!!!!

I just made it up from the video.

Kbueno · 04-15-2009, 11:22 AM

The locking bar was a bit of a pain, slid the connectors in..are they suppose to click? Car adapting nicely..gotta get used to the Service Engine Soon light flashing for which map you are on.....that light strikes fear in my heart when illuminated in the past.

veightkiller · 04-15-2009, 11:43 AM

Thanks for the vid!

joec500 · 04-15-2009, 01:09 PM

Quote:

Originally Posted by 335lvr

The locking bar was a bit of a pain, slid the connectors in..are they suppose to click? Car adapting nicely..gotta get used to the Service Engine Soon light flashing for which map you are on.....that light strikes fear in my heart when illuminated in the past.

I was wondering this too, I don't think they "click" seems more like a pressure fit thing, since it's so tight. I just inserted the pins, pushed down the lock bar and gave a solid tug to the CANBUS wires to make sure they were tight.

bestsw20 · 04-15-2009, 01:40 PM

Do I have to update the firmware before I do the harness upgrade? As I have the REVII from a month ago but I haven't install it yet. If I have to do the firmware update first, that's mean I have to install it and then update the firmware, than uninstall it to add the new update.. or I can just update my wiring before I install the REVII and then update the firmware??

joec500 · 04-15-2009, 01:43 PM

Quote:

Originally Posted by bestsw20

Do I have to update the firmware before I do the harness upgrade? As I have the REVII from a month ago but I haven't install it yet. If I have to do the firmware update first, that's mean I have to install it and then update the firmware, than uninstall it to add the new update.. or I can just update my wiring before I install the REVII and then update the firmware??

Unless you have an external power source for your procede, you need to install, then update the firmware.

Then you only uninstall part of the wiring harness from the ecu. You don't need to uninstall everything, in order to swap in your CANBUS wires.

04-14-2009, 03:18 PM	#1
OpenFlash 1736 Rep 17,960 Posts Drives: A Lot Join Date: Sep 2006 Location: SF Bay, CA iTrader: (0) Garage List 2018 Ducati Panigal ... [0.00] 2016 Mazda CX5 [0.00] 2017 Aprilia Tuono ... [0.00] 2019 BMW M2 Competi ... [0.00] 2015 BMW M5 Competi ... [10.00] 2016 Ducati XDiavel S [0.00] 2016 AMG GT S [0.00] 2011 Ferrari 458 It ... [0.00] 2017 Charger Hellcat [0.00] 2015 KTM Super Duke ... [0.00] 2016 KTM RC390 [0.00]	PROcede CANbus wiring update directions (video) Only for those who have NO CANbus wiring on their Rev.2 harness and received their CANbus wire pack update: (it's in HD!) Cheers, Shiv
	Appreciate 0 Tweet Quote

04-14-2009, 03:20 PM	#2
TMR Brigadier General 394 Rep 3,161 Posts Drives: M3 Join Date: Jun 2008 Location: Torrance iTrader: (12)	Works perfect. THANKS!!!!!!! Shiv, get in contact with me when you have a min.
	Appreciate 0 Quote

04-14-2009, 03:36 PM	#3
Vudoo4u2 Night Sh1ft 458 Rep 3,079 Posts Drives: F95 X5MC LCI Join Date: Oct 2007 Location: It's bobsled time iTrader: (3) Garage List 2024 BMW X5M Compet ... [0.00]	hey man, do we have to entirely uninstall the harness when we do this? Or can I just keep it plugged in, but swap those two wires (assuming my battery is disconnected before I start, and the procede firmware has already been loaded up w/o a engine start up) __________________ "Your first 10,000 photographs are your worst.” ― Henri Cartier-Bresson
	Appreciate 0 Quote

04-14-2009, 03:37 PM	#4
Tobias1980 Read the manual please, just do it before asking! 11 Rep 397 Posts Drives: F31 328i, F55 Cooper Join Date: Jan 2008 Location: Sweden iTrader: (0)	Nice Shiv! Do you have an ETA on new CANbus maps?
	Appreciate 0 Quote

04-14-2009, 03:40 PM	#7
Vudoo4u2 Night Sh1ft 458 Rep 3,079 Posts Drives: F95 X5MC LCI Join Date: Oct 2007 Location: It's bobsled time iTrader: (3) Garage List 2024 BMW X5M Compet ... [0.00]	thank you vm..psyched, I keep checking the mail for it! __________________ "Your first 10,000 photographs are your worst.” ― Henri Cartier-Bresson
	Appreciate 0 Quote

04-14-2009, 04:27 PM	#8
Bluewater335i Enlisted Member 0 Rep 46 Posts Drives: 09 335i Sedan Join Date: Nov 2008 Location: Chicago iTrader: (0)	Oops, I didn't see this post when posting this the first time... Just to be clear, I haven't installed my procede rev ii, non-CANBUS harness because I was waiting on the CANBUS cables. Do I need to install the procede (non-CANBUS) in my car and upgrade the firmware BEFORE I install the CANBUS cable? -or is there a way to update the firmware without installing the procede in the car? Thanks
	Appreciate 0 Quote

04-14-2009, 06:05 PM	#10
Kbueno Lieutenant Colonel 99 Rep 1,712 Posts Drives: F82 Join Date: Jan 2007 Location: California iTrader: (5)	You guys are confusing me! Sounds like that you update the firmware with the PROcede installed, then turn off wait 15 min...come back and change out wires. Is this correct?
	Appreciate 0 Quote

04-14-2009, 06:37 PM	#11
scalbert Major General 153 Rep 5,780 Posts Drives: '13 S4, '15 Q7 Join Date: Feb 2007 Location: Woodstock, GA iTrader: (8)	Thanks, I'm gald I did not just send an email asking before checking the forum.
	Appreciate 0 Quote

04-14-2009, 06:38 PM	#12
Dustin Bramell Lieutenant 44 Rep 428 Posts Drives: e90 335i, 125cc Trackmagic Join Date: Sep 2006 Location: Santa Monica, CA iTrader: (1)	It's very simple guys. 1. Update the firmware and map as you normally would. 2. Remove the grey connector, install the wires, and the replace the grey connector. If you are confused about the process, please send me a PM. I think posting here is just causing more confusion. thanks, DB-
	Appreciate 0 Quote

04-14-2009, 06:51 PM	#13
Vudoo4u2 Night Sh1ft 458 Rep 3,079 Posts Drives: F95 X5MC LCI Join Date: Oct 2007 Location: It's bobsled time iTrader: (3) Garage List 2024 BMW X5M Compet ... [0.00]	you plug in your key, but dont turn the engine over, just the power 1 click update your firmware, turn off the car. unplug your battery, then do the swap of the canbus wire __________________ "Your first 10,000 photographs are your worst.” ― Henri Cartier-Bresson
	Appreciate 0 Quote

04-14-2009, 09:41 PM	#16
shawshank772 Major 120 Rep 1,159 Posts Drives: 08 135i and 16 M3 Join Date: Aug 2007 Location: Chicago iTrader: (1)	WOW, honestly with 10 different people posting their own DIY on here its confusing. Simply follow the video step by step and you will be FINE I watched a couple people do it and it doesnt seem hard. Last edited by shawshank772; 12-22-2009 at 07:05 PM..
	Appreciate 0 Quote

04-15-2009, 11:22 AM	#18
Kbueno Lieutenant Colonel 99 Rep 1,712 Posts Drives: F82 Join Date: Jan 2007 Location: California iTrader: (5)	The locking bar was a bit of a pain, slid the connectors in..are they suppose to click? Car adapting nicely..gotta get used to the Service Engine Soon light flashing for which map you are on.....that light strikes fear in my heart when illuminated in the past.
	Appreciate 0 Quote

04-15-2009, 11:43 AM	#19
veightkiller Brigadier General 61 Rep 4,150 Posts Drives: e90 335i Join Date: Dec 2007 Location: Vancouver,B.C iTrader: (3)	Thanks for the vid!
	Appreciate 0 Quote

04-15-2009, 01:40 PM	#21
bestsw20 Enlisted Member 1 Rep 46 Posts Drives: 2009 135i Join Date: Nov 2008 Location: Toronto iTrader: (0)	Do I have to update the firmware before I do the harness upgrade? As I have the REVII from a month ago but I haven't install it yet. If I have to do the firmware update first, that's mean I have to install it and then update the firmware, than uninstall it to add the new update.. or I can just update my wiring before I install the REVII and then update the firmware??
	Appreciate 0 Quote