|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Good place for brakes? suggestions?
|
|
08-06-2010, 01:59 AM | #1 |
Private
7
Rep 53
Posts |
Good place for brakes? suggestions?
anyone know a good place that does a good job on brakes on my 2006 325i? the only place i have around here is Midas and Les Schwab and from what i hear is they do a sh*t job, need a good, trusty, reliable spot, any suggestions?
|
08-06-2010, 12:07 PM | #2 |
Brigadier General
198
Rep 4,647
Posts |
i do most general work at this mechanic shop called NetAutoCafe in Lynnwood. pretty cool place and they have computers and drinks while you wait, rather than sit there do nothing. very friendly and clean with good reviews too.
http://www.yelp.com/biz/net-auto-cafe-lynnwood all bmw specific repairs and services, i go to parkers. http://broadstrokeassociates.com/default.aspx
__________________
SGE92TT......................... 12.331 Sec @ 117.89 Mph............................POWERED BY
l BMS DCI l HELIX IC l FORGE DVs l RR OCC & CP & SCOOPS l AR 3" DPs l AE QUADs l BLISTEIN PSS10 l P3 VENT GUAGE l VISHNU PROCEDE V5 AUTOTUNE l Lots of Window Stickers |
Appreciate
0
|
08-06-2010, 01:28 PM | #3 |
Lieutenant
31
Rep 402
Posts |
It's not a hard job at all to DIY. It's one of the easiest DIY's. Take off wheel. Remove plastic caps (2) that are covering the caliper guide pins (which hold caliper onto caliper carrier). Remove caliper guide pins (I think it's a 7mm Allen/hex). Once those pins out, remove caliper and either set it on a flower pot, wire it up, etc. so that caliper is not hanging from brake hoses. Take cap off brake fluid reservoir and put rag around it in case some fluid comes out when you retract calipers. If you replacing pads, take out old pads (remove clip on caliper, pads should fall out). Retract calipers using a free rent tool from Autozone. Put anti-squeal if you want on the BACK of the pads, not the face of the pad, install new pads onto caliper, put clips on carrier, and re-install caliper onto caliper carrier.
If you want to replace rotors as well (suggested), remove two bolts holding caliper carrier onto the knuckle. One they iare removed, rotor should come off. Install new rotor. Install caliper carrier. Install caliper using guide pins (suggest cleaning guide pins and putting new lube on them). Once you are done, check master clyinder to see who much fluid leaked out when retracted calipers. Fill to level and put top on. Put board or something under brake pedal (to prevent pedal from going all the way to the floor) and pump brakes. If you wish, you may bleed brakes suggested) or take it to a shop. Honestly, it is a severely easy DIY (I just did it on my BMW, AUdi, and a friend's trcuk)). First side should take 30-60 minutes if you haven't done them before to figure out, other sides should take less than 30 minutes each. |
Appreciate
0
|
08-06-2010, 01:59 PM | #4 |
Private
7
Rep 53
Posts |
@hun77777 Thanks man, imma look into that
@orangedawg Thank you too but honestlly, i dont trust myself, i would rather pay a professional to do it, but thank you for the info, ill keep the DIY stuff in mind |
Appreciate
0
|
Bookmarks |
|
|