|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
Super easy way to remove front interior light cluster for LED or hard wiring detector
|
|
01-03-2013, 01:27 PM | #1 |
Lieutenant
174
Rep 575
Posts |
Super easy way to remove front interior light cluster for LED or hard wiring detector
This is such an easier way and works for so many different reasons to remove front center interior light cluster. That I felt it was worthy of it's own thread. Such as hard wiring a radar detector, replacing bulbs with LED's or just plain manual access to sunroof.
The first thing I did was bend a strong nail. I accidentally bent it too much on one end. The smaller end works best. However the bend on the larger end helped for pulling. I then removed the frosted plastic and the map light lens. This picture shows the metal clip visible through a hole in the back of the map light. I then fished the small end of the bent nail behind the silver clip and pulled back towards rear of car. Which in less than thirty seconds releases the clip. I tried many of the other methods using my fat fingers along the front windshield didn't work for me. Neither did a screwdriver butter knife, small screwdriver etc (please note the putty knife and brand new screwdriver I tried using both marred the interior.) Also I just grabbed the first nail a thinner one would have worked even better. Or even better if you have one of those screwdrivers with a bent hook tip... I think they are technically a radiator hose remover. They always come with the uber cheap gas station dollar tool bin set. I finally found a use for that tool...lol |
01-08-2013, 12:34 AM | #2 |
Private
1
Rep 60
Posts |
I had a hell of a time releasing the clip the holds in the front dome light/map lights assembly too until my friend helping me recommended unscrewing the sun visor holders.
This allows the headliner to drop down MUCH more and allowed even my fat hands to easily reach the front of the front dome light/map lights assembly to unclip for easy removal. |
Appreciate
0
|
04-08-2013, 04:54 PM | #4 |
Enlisted Member
3
Rep 34
Posts |
Crashoverride.... you are my saviour, just been trying for 2 hours to get that bloody front light dome out without success, tried the screwdriver, spatula etc and all I got was a cut hand...!
I looked at it and wondered about trying to get to the clip through the light but of course it's hard to see until you get the damn thing out, so your pics show me it can be done. So I've taken an old wire coat hanger, cut it about 6 inches long, bent hook at one end and loop at the other to grip onto.. I haven't tried it yet but damn I know it's gonna work.. so many thanks. How many people on here have struggled with this... ? easy now, I'll let you know how it works. Cheers |
Appreciate
0
|
04-09-2013, 02:35 PM | #5 |
Enlisted Member
3
Rep 34
Posts |
OK, tried the coat-hanger, small 1/4" bend at one end and loop at the other to grab onto... took me about three mins to get the light housing out... perfect.
Don't make the bent bit any bigger than 1/4" as it won't fit through the gap in the light, one side at a time, used the plastic spatula thing to hold the first side in place to stop it popping back in then did the other side clip. The real annoying thing is the light goes back in just so easy... |
Appreciate
0
|
04-09-2013, 02:48 PM | #6 |
Lieutenant
174
Rep 575
Posts |
Awesome I'm so glad others could take advantage of this. It truly is frustrating beyond belief and I feel this is such easy solution to a such a hard problem.
It confuses me that you're supposed to actually get in that area to manually close sunroof... usually in a rainstorm. I mean only a consumer would manually close... yet there is no easy just pull this release or such to get in there. |
Appreciate
0
|
12-02-2013, 05:49 PM | #7 |
First Lieutenant
31
Rep 363
Posts |
I know this thread is old, but thank you for this. i was able to change all of my bulbs with no issues except one map light. This allowed me to get the fixture lowered so I could access the bulb from above. Thanks!
|
Appreciate
0
|
12-11-2013, 12:46 AM | #9 |
Captain
77
Rep 980
Posts
Drives: '08 BSM 335i e92
Join Date: Oct 2013
Location: Norfolk
|
How do you remove the map light lens? I can't seem to get it off. Anyone provide a picture of how to get it off? Where do I pry?
__________________
'08 BSM E92 335i 6MT/MHD stg 2+/VRSF 7" FMIC/VRSF CP/HKS BOV/VRSF catless DPs/BMS DCI/muffler delete/BC Extreme lows/OEM style 167s/BMS high side OCC/Mishimoto low side OCC/etc
|
Appreciate
0
|
12-17-2013, 11:10 PM | #10 | |
Brigadier General
681
Rep 3,696
Posts |
Quote:
The side closest the windshield or closest the sunroof is actually flat rather than rounded a bit (hard to notice at first). You can use your tools to wedge, wiggle, pry it off. Once you got that off... I found it easier to remover the sun visor clip nearest to the FZD. Once the screw and clips r removed... U can easily reach behind the sun visor to press the metal tabs so the FZD pops down. |
|
Appreciate
0
|
04-02-2017, 06:56 AM | #11 | |
Private
13
Rep 59
Posts
Drives: 2015 M235i
Join Date: Feb 2014
Location: Los Angeles
|
Quote:
__________________
18x8.5 et35 VMR 803, Stoptech Trophy Series Front BBK, M4 LCA,KW V2, Seibon CF Hood, APR Gtc250, Agency harness bar, Corbeau A4 Raving Seats and 4pt Harnesses, P3 Display, XHP Stage 3, PR Coils -TTFS-XDI35 hpfp ~CaryJordan Tune Full E85~aFE Momentum GT, Stage 2.5 Walbro 535 LPFP, MPerfExhaust, Quad CF Sleeve Tips, custom quad cf rear diffuser, M2 Style Front bumper with lip. Avery Dark Grey Gloss Vinyl
|
|
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|