Procede 2 with a AT

335Turbo · 12-10-2007, 05:20 PM

Well now that my car has adapted to the Procede, it's aways in the wrong gear! It's almost a must to have it in DS when trucking around town and going up hills. Has anyone else noticed this?

sflgator · 12-10-2007, 05:22 PM

I always use my paddles, but if you drive in DS without paddles, then give your car a couple days to adapt. btw -- did you follow the v2.0.2 map instructions and disconnect the negative terminal (black cable wire) from your battery?

This resets the ECU, so it will adapt to your v2 right away.

AM335 · 12-10-2007, 05:28 PM

Quote:

Originally Posted by 335Turbo

Well now that my car has adapted to the Procede, it's aways in the wrong gear! It's almost a must to have it in DS when trucking around town and going up hills. Has anyone else noticed this?

Is your 335 difficult to drive when in 'D' mode? How does it behave in 'D' mode? Thanks.

WOPALX · 12-10-2007, 05:44 PM

Guy's I installed my V2 this morning & loaded the 2.02 AT map. No issues and the car is driving well thus far.

I noticed Shiv has posted a revised AT 2.02 map this morning so am looking at loading that before I go for another drive. Question is should I go through the process of disconnecting the battery before I load the revised map?

Thanks in advance.

bmwzimmer · 12-10-2007, 05:45 PM

Let it adapt and then up the setting a couple percent and you should notice most of the tq. back.

bmwzimmer · 12-10-2007, 05:47 PM

Quote:

Originally Posted by WOPALX

Guy's I installed my V2 this morning & loaded the 2.02 AT map. No issues and the car is driving well thus far.

I noticed Shiv has posted a revised AT 2.02 map this morning so am looking at loading that before I go for another drive. Question is should I go through the process of disconnecting the battery before I load the revised map?

Thanks in advance.

Shiv doesn't on his car and neither do I. It doesn't hurt though...

My settings are at 94 and the car feels very strong.

335Turbo · 12-10-2007, 08:50 PM

Quote:

Originally Posted by AM335

Is your 335 difficult to drive when in 'D' mode? How does it behave in 'D' mode? Thanks.

I wouldn't go as far as saying it's difficult to drive. I just want it to down shift sometime and it doesn't. It's almost like the added boost is providing enough power so it just keeps on going.. But it's not, as the car starts to slow down.. You then press harder on the gas and nothing too extremes happens.. As you give it more gas the car will eventually shift and at that point you are really moving! Haven't tried .2 yet, but I will before I go to work tomorrow. BTW I'm experiencing this when traveling at approximately 40mph and driving up an incline.. What do you think would happen if I drop the values below 2,500RPM 5%?

bmwzimmer · 12-10-2007, 08:55 PM

Don't do it. 2%, then 1% from there. Check boost first and make sure your running at least 93 octane if your going to go as high as 94%

ontopofm · 12-10-2007, 10:03 PM

my car is over 100 miles with V2.02.02, it drives so stock-like. i feel it's slow compare to previous map perhaps 30-50 less torque. 2nd, 3rd, and 4th gear dont pull as hard below 5k rpm. is 91 octance good enough for 92% (or maybe 91%) across the board?

v2bling · 12-10-2007, 10:13 PM

Hum.. i cant really tell, but it seems googoo fast up top. I just set my settings to 92 percent though and loaded the update map. I will let you know how it goes after i do 50 miles tomm. Dont forget to do battery disconnect for hour and half and ecu reset through software before loading map.

Ontopofm - you can put to 92 percent max with 91 octane.
94 percent is for 93 octane users
97 percent is for 96 octane users

ontopofm · 12-10-2007, 10:47 PM

just loaded the updated map and did some pulls to redline. hope i can feel the difference tomorrow. if not i will dial up to 91 and then 92% if needed. thanks v2bling

rlb · 12-10-2007, 11:09 PM

ontopofm,
Do you get 1/2 engine light/limp mode at 6700 rpm at the 3-4 shift. If you could try this it would be very helpful.

OpenFlash · 12-10-2007, 11:11 PM

Hi guys,
See: http://www.e90post.com/forums/showpo...6&postcount=39

ontopofm · 12-10-2007, 11:24 PM

Quote:

Originally Posted by rlb

ontopofm,
Do you get 1/2 engine light/limp mode at 6700 rpm at the 3-4 shift. If you could try this it would be very helpful.

i dont get any engine light or limp, but i think i was doing from 2nd-3rd pull

ontopofm · 12-11-2007, 01:06 AM

Quote:

Originally Posted by rlb

ontopofm,
Do you get 1/2 engine light/limp mode at 6700 rpm at the 3-4 shift. If you could try this it would be very helpful.

updated: i just did that and everything seems fine, default settings

12-10-2007, 05:20 PM	#1
335Turbo Enlisted Member 2 Rep 37 Posts Drives: 335 Join Date: Nov 2007 Location: US iTrader: (0)	Procede 2 with a AT Well now that my car has adapted to the Procede, it's aways in the wrong gear! It's almost a must to have it in DS when trucking around town and going up hills. Has anyone else noticed this?
	Appreciate 0 Tweet Quote

12-10-2007, 05:22 PM	#2
sflgator Major General 148 Rep 5,389 Posts Drives: '09 MB C63 AMG & '08 MB GL450 Join Date: Oct 2006 Location: U.S. iTrader: (1)	I always use my paddles, but if you drive in DS without paddles, then give your car a couple days to adapt. btw -- did you follow the v2.0.2 map instructions and disconnect the negative terminal (black cable wire) from your battery? This resets the ECU, so it will adapt to your v2 right away. __________________ \|2009 RENNtech MB C63 AMG \| Black/Black Leather/Black Maple \| Premium II \| MultiMedia \| iPod \| \| TeleAid \| Charcoal Filter Delete \| BMC High-Flow Air Filters \| High-Flow Secondary Cats \| Clear Side Markers \|
	Appreciate 0 Quote

12-10-2007, 05:44 PM	#4
WOPALX Lieutenant Colonel 86 Rep 1,993 Posts Drives: 335i Sedan Join Date: May 2007 Location: Sydney, Australia iTrader: (2)	Guy's I installed my V2 this morning & loaded the 2.02 AT map. No issues and the car is driving well thus far. I noticed Shiv has posted a revised AT 2.02 map this morning so am looking at loading that before I go for another drive. Question is should I go through the process of disconnecting the battery before I load the revised map? Thanks in advance.
	Appreciate 0 Quote

12-10-2007, 05:45 PM	#5
bmwzimmer Major 35 Rep 1,084 Posts Drives: 335 Join Date: Jan 2007 Location: 91 octane states iTrader: (0)	Let it adapt and then up the setting a couple percent and you should notice most of the tq. back.
	Appreciate 0 Quote

12-10-2007, 08:55 PM	#8
bmwzimmer Major 35 Rep 1,084 Posts Drives: 335 Join Date: Jan 2007 Location: 91 octane states iTrader: (0)	Don't do it. 2%, then 1% from there. Check boost first and make sure your running at least 93 octane if your going to go as high as 94%
	Appreciate 0 Quote

12-10-2007, 10:03 PM	#9
ontopofm Lieutenant Colonel 76 Rep 1,548 Posts Drives: stock Join Date: Jun 2007 Location: CA iTrader: (4)	my car is over 100 miles with V2.02.02, it drives so stock-like. i feel it's slow compare to previous map perhaps 30-50 less torque. 2nd, 3rd, and 4th gear dont pull as hard below 5k rpm. is 91 octance good enough for 92% (or maybe 91%) across the board?
	Appreciate 0 Quote

12-10-2007, 10:13 PM	#10
v2bling First Lieutenant 7 Rep 301 Posts Drives: speed demon Join Date: Dec 2007 Location: Mansfield,tx iTrader: (0)	Hum.. i cant really tell, but it seems googoo fast up top. I just set my settings to 92 percent though and loaded the update map. I will let you know how it goes after i do 50 miles tomm. Dont forget to do battery disconnect for hour and half and ecu reset through software before loading map. Ontopofm - you can put to 92 percent max with 91 octane. 94 percent is for 93 octane users 97 percent is for 96 octane users
	Appreciate 0 Quote

12-10-2007, 10:47 PM	#11
ontopofm Lieutenant Colonel 76 Rep 1,548 Posts Drives: stock Join Date: Jun 2007 Location: CA iTrader: (4)	just loaded the updated map and did some pulls to redline. hope i can feel the difference tomorrow. if not i will dial up to 91 and then 92% if needed. thanks v2bling
	Appreciate 0 Quote

12-10-2007, 11:09 PM	#12
rlb Private First Class 5 Rep 117 Posts Drives: 335i, 300ZX Join Date: Feb 2007 Location: Northern NJ iTrader: (0)	ontopofm, Do you get 1/2 engine light/limp mode at 6700 rpm at the 3-4 shift. If you could try this it would be very helpful.
	Appreciate 0 Quote

12-10-2007, 11:11 PM	#13
OpenFlash 1736 Rep 17,960 Posts Drives: A Lot Join Date: Sep 2006 Location: SF Bay, CA iTrader: (0) Garage List 2018 Ducati Panigal ... [0.00] 2016 Mazda CX5 [0.00] 2017 Aprilia Tuono ... [0.00] 2019 BMW M2 Competi ... [0.00] 2015 BMW M5 Competi ... [10.00] 2016 Ducati XDiavel S [0.00] 2016 AMG GT S [0.00] 2011 Ferrari 458 It ... [0.00] 2017 Charger Hellcat [0.00] 2015 KTM Super Duke ... [0.00] 2016 KTM RC390 [0.00]	Hi guys, See: http://www.e90post.com/forums/showpo...6&postcount=39
	Appreciate 0 Quote