|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
PROcede CANbus diagnostic code reading DONE
|
|
12-12-2009, 01:05 PM | #199 |
Second Lieutenant
15
Rep 235
Posts |
scott, did you get a value of "0" on the CANbus code channel?
__________________
cosmetic mods - BBS LM's, body colored reflectors, 30% tint
permormance mods - procede rev II, vishnu dci, helix fmic, ar catless dp's |
Appreciate
0
|
12-12-2009, 04:25 PM | #200 |
Brigadier General
133
Rep 4,764
Posts |
|
Appreciate
0
|
12-12-2009, 08:33 PM | #201 |
Major General
153
Rep 5,780
Posts |
|
Appreciate
0
|
12-13-2009, 12:40 AM | #202 |
Brigadier General
133
Rep 4,764
Posts |
|
Appreciate
0
|
12-13-2009, 08:05 AM | #203 | |
Major General
153
Rep 5,780
Posts |
Quote:
But you then have to depress the acceoerator to enable the function. |
|
Appreciate
0
|
12-13-2009, 10:00 AM | #204 |
Brigadier General
133
Rep 4,764
Posts |
Yeah. Did that. Nothing showed on the data logging - view datalog screen. The screen was empty, even though I was connected. Is that where I should have been looking? Thanks!
|
Appreciate
0
|
12-13-2009, 10:23 AM | #205 |
Major General
153
Rep 5,780
Posts |
|
Appreciate
0
|
12-13-2009, 10:59 AM | #206 | |
Brigadier General
133
Rep 4,764
Posts |
Quote:
Do you have to start logging to get the DME code values to populate, or should they just show up from depressing the accelerator? |
|
Appreciate
0
|
12-13-2009, 11:32 AM | #207 |
Team Zissou
3064
Rep 10,197
Posts |
did you do this exactly?
1. get in car 2. plug in laptop 3. turn ignition on (do not start the car, just press the start button with the key in) 4. go online with the procede software 5. press throttle to the floor... hear a "ding" and half engine light appears. 6. codes will display one at a time |
Appreciate
0
|
12-13-2009, 01:00 PM | #208 | |
Brigadier General
133
Rep 4,764
Posts |
Quote:
|
|
Appreciate
0
|
12-13-2009, 01:57 PM | #209 |
Captain
72
Rep 978
Posts |
There's no logging needed (I suppose you could log the codes technically if you wanted, since it's a channel). Just make sure as jp said that you've plugged in your laptop, Procede is connected, and THEN you press the gas pedal all the way, half engine light shows up, and then the channel CAN DME Codes on the main Procede screen will flash the various codes every few seconds (as long as you had added it as a channel already, of course).
I initially used to think all I had to do was plug in the laptop and connect to Procede and I'd see the codes in that channel. But it doesn't happen until you press the gas pedal all the way to the floor. Then the codes start showing up, as that signals the Procede to read the codes and show them in that channel. Good luck. |
Appreciate
0
|
12-13-2009, 02:02 PM | #210 |
Brigadier General
133
Rep 4,764
Posts |
When you say "main" procede screen. Do you meen the first screen when you start the software? I was going on the menu bar to data loggind, view datalog.
|
Appreciate
0
|
12-13-2009, 02:05 PM | #212 |
Brigadier General
133
Rep 4,764
Posts |
Cool. I will go update to the 11-2 firmware and maps now, and try it again. Thanks!
|
Appreciate
0
|
12-13-2009, 02:18 PM | #213 | |
Brigadier General
133
Rep 4,764
Posts |
Quote:
http://www.e90post.com/forums/showpo...58&postcount=1 |
|
Appreciate
0
|
12-13-2009, 02:24 PM | #215 |
Brigadier General
133
Rep 4,764
Posts |
Yeah! Thanks! There was a lot of confusion on the other thread as well. It just seems you have to be upto speed on little pieces of info you find in multiple threads, to really be sure you are doing the right thing. The audio on the video obviously says to go to the data logging screen, but a quick shot of video actually showing it display the codes would have cleared up that confusion.
I've got some Dyno time scheduled this Tuesday. Was hoping to do meth and non-meth to see the difference, but the kit probably wont be here in time. |
Appreciate
0
|
12-13-2009, 02:27 PM | #216 |
Brigadier General
133
Rep 4,764
Posts |
One other question if anyone knows. Is the procede reading all the modules like the BT tool, or just the engine module? It returns the codes so darn fast.
|
Appreciate
0
|
12-13-2009, 02:34 PM | #217 |
e92
4
Rep 391
Posts |
|
Appreciate
0
|
12-13-2009, 10:46 PM | #218 | |
Captain
72
Rep 978
Posts |
Quote:
The codes do flash by pretty quickly, but they stay for a while (unless you accidentally press the gas pedal again and clear them!), so don't panic, just write them all down and then look them up in the spreadsheet Shiv posted with descriptions of what they mean. |
|
Appreciate
0
|
03-24-2010, 02:14 AM | #219 |
Colonel
324
Rep 2,663
Posts
Drives: BMW 335xi Sedan; BMW M3 ZCP
Join Date: Nov 2007
Location: NYC
|
WoW, Shiv been working on "Boost display in dash" since July of 2009.
__________________
335xi Sedan 6AT | Weather(70-85°F) | N54 Tune Comparison Chart || N54 Turbo Upgrade Comparison Chart
-PROcede Rev. 2.5 ~ v5 (3/17 maps) / JB4 (8/21 maps) / COBB (Stg2+FMIC LT Aggressive maps) †Procede Map2(UT 45 - IGN 40) Aggression Target 2.0 | 0-60 in 4.0sec || †Cobb E30 LT (35% Ethanol/65% 93 Octane) | 0-60 in 3.9sec AR Design Catless DP | BMS DCI + OCC | ETS 5 FMIC | Alpina B3 Trans Flash |235/265 19" Michelin PSS |
Appreciate
0
|
Bookmarks |
|
|