|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
o2 sensor code help
|
|
08-17-2011, 05:24 PM | #1 |
ايلي ٣٣٥ هاهاها
88
Rep 1,448
Posts |
o2 sensor code help
Hello fellas;
I've recently installed catless downpipes, and since then I always get the code 2C3E: 2C3E Lambda probe in front of catalytic converter 2, control failure or cable transmission failure? Any idea what's the cause of the error? I've searched, nothing explained why could be. Can someone please chime in and explain? Thanks
__________________
|
08-17-2011, 05:36 PM | #2 |
Major General
161
Rep 7,377
Posts |
Seems like the front lambda 2 has issues after the installation of the dps, maybe broken or reverted? I would check that first.
__________________
07 335i AT - MOTIV 750 - MHD E85 BMS flash - BMS PI - JB4G5 - Okada Coils - NGK 5992 Plugs - Helix IC - Snow Stg. 3 - Stett CP - Custom midpipes with 100 HJS Cats - Bastuck Quad - PSS10 - QUAIFE LSD - BMS OCC - Forge DVs - AR OC - ALCON BBK - M3 Chassi - Dinan CP - Velocity M rear Toe arms - Advan RZ-DF - LUX H8 - Level 10 AT upgrade
|
Appreciate
0
|
08-17-2011, 05:43 PM | #4 |
1737
Rep 17,960
Posts
Drives: A Lot
Join Date: Sep 2006
Location: SF Bay, CA
iTrader: (0)
Garage List 2018 Ducati Panigal ... [0.00]
2016 Mazda CX5 [0.00] 2017 Aprilia Tuono ... [0.00] 2019 BMW M2 Competi ... [0.00] 2015 BMW M5 Competi ... [10.00] 2016 Ducati XDiavel S [0.00] 2016 AMG GT S [0.00] 2011 Ferrari 458 It ... [0.00] 2017 Charger Hellcat [0.00] 2015 KTM Super Duke ... [0.00] 2016 KTM RC390 [0.00] |
|
Appreciate
0
|
08-17-2011, 05:45 PM | #5 | |
ايلي ٣٣٥ هاهاها
88
Rep 1,448
Posts |
Quote:
can you be more specify on the location of the lambda 2 please? I mean which downpipe to check, passenger side or driver side?
__________________
|
|
Appreciate
0
|
08-17-2011, 05:50 PM | #6 |
Major General
161
Rep 7,377
Posts |
Pretty sure is bank 2 (cyl 4-5-6) which should be the driver side dp? Not 100% sure though.
__________________
07 335i AT - MOTIV 750 - MHD E85 BMS flash - BMS PI - JB4G5 - Okada Coils - NGK 5992 Plugs - Helix IC - Snow Stg. 3 - Stett CP - Custom midpipes with 100 HJS Cats - Bastuck Quad - PSS10 - QUAIFE LSD - BMS OCC - Forge DVs - AR OC - ALCON BBK - M3 Chassi - Dinan CP - Velocity M rear Toe arms - Advan RZ-DF - LUX H8 - Level 10 AT upgrade
|
Appreciate
0
|
08-17-2011, 05:58 PM | #7 | |
ايلي ٣٣٥ هاهاها
88
Rep 1,448
Posts |
Quote:
so its the upper O2 sensor on the downpipe that controls cyl 4 5 6 to be checked
__________________
|
|
Appreciate
0
|
08-17-2011, 06:06 PM | #8 |
ايلي ٣٣٥ هاهاها
88
Rep 1,448
Posts |
oh my bad, its not the upper sensor, its the O2 sensor after the catalytic converter which is on the down side of the downpipe...
__________________
|
Appreciate
0
|
08-17-2011, 06:12 PM | #9 |
Major General
161
Rep 7,377
Posts |
No think is the wideband sensor pre cat/closest to the turbo. The important one.
__________________
07 335i AT - MOTIV 750 - MHD E85 BMS flash - BMS PI - JB4G5 - Okada Coils - NGK 5992 Plugs - Helix IC - Snow Stg. 3 - Stett CP - Custom midpipes with 100 HJS Cats - Bastuck Quad - PSS10 - QUAIFE LSD - BMS OCC - Forge DVs - AR OC - ALCON BBK - M3 Chassi - Dinan CP - Velocity M rear Toe arms - Advan RZ-DF - LUX H8 - Level 10 AT upgrade
|
Appreciate
0
|
08-17-2011, 06:31 PM | #10 |
First Lieutenant
25
Rep 330
Posts |
I had the exact same code reading off my JB4 which caused my car to run lean and the tune would actually turn itself off when I was on it. Had the o2 sensor replaced on bank 4 I believe?? No more CELs and I havn't had a code come up yet, car runs stronger and better now.
|
Appreciate
0
|
08-17-2011, 09:29 PM | #11 |
Major
36
Rep 1,054
Posts |
See, I am thinking that I have been having this issue as well. I have an after cat code, says its not plugged in or something. I use a DP fix from BMS and it goes away. I remember the car being a lot stronger. I put in the dp fix for my inspection and I have been trying to figure out how vital this code is. Wish I still had the exact code #. I have to detach my dp fix to make it come up again.
I guess if I were going to invest some money in a sound running car, I would want to replace all these sensors? Or should I focus on the fronts? I still haven't got a solid grasp on o2 sensors and their function in relation to AFR.
__________________
JB4 beta 15 ohms FSB,AEM inline filter/ CM 10, ETS fmic, ER custom made charge pipe,TSW Donnington 18's,Simitumo HTRZ3, Injen DCI, AR DPs, Forge DVs, AA SLD, Koni FSD, ZSP springs.
|
Appreciate
0
|
08-18-2011, 05:00 PM | #12 |
ايلي ٣٣٥ هاهاها
88
Rep 1,448
Posts |
Update:
Changed both O2 sensors on the DP for cyl 4-5-6, and the error is gone.
__________________
|
Appreciate
0
|
Bookmarks |
|
|