BMW CODING success

BPMSport · 03-10-2011, 03:16 AM

Quote:

Originally Posted by rubdom

Added the alarm VO but not able to read the alarm modules. I keep getting an error stating "no response from ECU". I guess this is not right unless I didn't add the alarm VO correctly.

I don't really want to spend $300 on an alarm. There has got to be a way to get that clown nose blinking

You can code the +302 option to your VO, and that will add DWAI and DWAS to the list. NCS expert reads the vehicle order just like the dealer systems do, and based on that will offer a predetermined set of options.

So if you added it to the VO, you still would never be able to connect to DWAI or DWAS because that requires the actual alarm module to be installed in the rear fender liner, connected to the CAN bus network through the pre- wired factory connector.

I am not sure about this because I haven't looked - but I would suspect that the clown nose blink is going to be somewhere in the NFRM module, or it could be in another one possibly..

You should also be able to control the blinking of the hazards through the idrive even without the alarm on locking/unlocking. The sound choices you could probably code also (there are 4 possible options on that menu), but obviously it wouldn't beep without the module and siren in there. I think the module and the siren are one piece. DWAI is the alarm module and DWAS is the siren part of the alarm system. There are some functions that crossover however.

Hope this helps

Pseudo Nim · 03-10-2011, 08:01 AM

update - adding $481 (sport seats) didn't enable paddleshift. Grr.

I guess i should take the wheel apart and test the paddles with a multimeter...

Pseudo Nim · 03-10-2011, 08:04 AM

Quote:

Originally Posted by rubdom

Don't know what this is but I found it in my EGS module:
It references Paddles there so you may want to look into that.

Quote:

Originally Posted by DESI4life10

Yea that Padddle does not work unfortunately. All cars have it set at wert_00 whether you have paddles or not.

I wonder if there is a wert_02 or 03 for the function. Maybe there is another wert option for those retrofitting.

Yeah that was my initial guess, but your EGS module is _identical_ to mine, so no go there.

Quote:

Originally Posted by outie

I don't think it makes much sense to add those to have paddle shift to work. Is there a way to confirm that your paddles are working hardware-wise?

Yeah, looks like I have to take everything apart and somehow test them. They do come off a (supposedly) functioning car, though ... so I can't see them NOT working. Hrm.

rubdom · 03-10-2011, 08:41 AM

Quote:

Originally Posted by Mike@Powerchip

You can code the +302 option to your VO, and that will add DWAI and DWAS to the list. NCS expert reads the vehicle order just like the dealer systems do, and based on that will offer a predetermined set of options.

So if you added it to the VO, you still would never be able to connect to DWAI or DWAS because that requires the actual alarm module to be installed in the rear fender liner, connected to the CAN bus network through the pre- wired factory connector.

I am not sure about this because I haven't looked - but I would suspect that the clown nose blink is going to be somewhere in the NFRM module, or it could be in another one possibly..

You should also be able to control the blinking of the hazards through the idrive even without the alarm on locking/unlocking. The sound choices you could probably code also (there are 4 possible options on that menu), but obviously it wouldn't beep without the module and siren in there. I think the module and the siren are one piece. DWAI is the alarm module and DWAS is the siren part of the alarm system. There are some functions that crossover however.

Hope this helps

Yeah I figured this was the case. I see an option on my main file that has an option for DWS (this was before I added the alarm VO) it is set to not active. I read on another forum that if you set this to active you get the clown blinker. I have never coded the entire car before so I am hesitant to try it. I now others that have had problems when they use the "code car" option. I'll dig around in NFRM a little more to see if anything looks like it would work.

Pseudo Nim · 03-10-2011, 08:44 AM

+1 - I wouldn't use "code car", ever. I dunno, it just sounds like a recipe for disaster unless proven otherwise.

E90PAT · 03-10-2011, 08:57 AM

holy hell, they made this into better then a sticky!! they dedicated its own section now!

antiks · 03-10-2011, 08:58 AM

Quote:

Originally Posted by E92PAT

holy hell, they made this into better then a sticky!! they dedicated its own section now!

lol.. we win!

Pseudo Nim · 03-10-2011, 08:59 AM

haha win!

Kalud · 03-10-2011, 08:59 AM

Nice!

Pseudo Nim · 03-10-2011, 09:01 AM

Quote:

Originally Posted by antiks

lol.. we win!

Quote:

Originally Posted by Pseudo Nim

haha win!

Quote:

Originally Posted by Kalud

Nice!

ok less party, more code. back on topic!

/me cracks whip

antiks · 03-10-2011, 09:06 AM

Quote:

Originally Posted by Pseudo Nim

ok less party, more code. back on topic!

/me cracks whip

agree... time to make stickies!

brinx38 · 03-10-2011, 09:16 AM

e90/e92 retrofitted CIC dump
Hi, is there anyone (in US/Canada) with a retrofitted CIC?
I would like to compare a dump of the trace file to diagnose a problem with my Bluetooth.

It sorta half way connects..
I can dial from the phone and it plays thru' the car but the car says bluetooth is not connected, even though it shows the signal strength on the screen.

can anyone help?

Thanks.

BlaSTiWi · 03-10-2011, 09:26 AM

I thought I've seen it before but couldn't find it ... is there a function to prevent LCI AE from dimming or just make it stay at full voltage?

Tkx!

onebadmofo · 03-10-2011, 09:28 AM

Quote:

Originally Posted by BlaSTiWi

I thought I've seen it before but couldn't find it ... is there a function to prevent LCI AE from dimming or just make it stay at full voltage?

Tkx!

Been looking for that for ages. So far nothing

BlaSTiWi · 03-10-2011, 09:37 AM

Yeah darn it ... I think what I saw somewhere along the way maybe for pre-LCI ...

I've seen this somewhere... anybody tried it?:

Code:

PWM_FL_FKT_DRL_33
wert_01 to wert_03 = Dimmungswert

wert_01 is the default and NCS Dummy listed possible value as high as wert_04 ...

Quote:

Originally Posted by onebadmofo

Been looking for that for ages. So far nothing

onebadmofo · 03-10-2011, 10:00 AM

Quote:

Originally Posted by BlaSTiWi

Yeah darn it ... I think what I saw somewhere along the way maybe for pre-LCI ...

I've seen this somewhere... anybody tried it?:

Code:

PWM_FL_FKT_DRL_33
wert_01 to wert_03 = Dimmungswert

wert_01 is the default and NCS Dummy listed possible value as high as wert_04 ...

Believe me when I tell you that I've tried every single line that has SL, DRL, FKT or RL_BL in it

spera23 · 03-10-2011, 10:23 AM

Quote:

Originally Posted by rubdom

Anyone know if you can code the clown nose to blink without an alarm? I know on older cars the dealer was able to do this. There has got to be a way with NCS. I don't want an alarm but the blinker would be a nice deterrent.

Would I be able to add the alarm to the VO and only activate the blinker?

+1 - Been Looking for this exact same thing on my 07 e92!!

spera23 · 03-10-2011, 11:04 AM

Quote:

Originally Posted by rubdom

Yeah I figured this was the case. I see an option on my main file that has an option for DWS (this was before I added the alarm VO) it is set to not active. I read on another forum that if you set this to active you get the clown blinker. I have never coded the entire car before so I am hesitant to try it. I now others that have had problems when they use the "code car" option. I'll dig around in NFRM a little more to see if anything looks like it would work.

I tried adding $302 to the VO and also found DWS in my CAPPL module. Tried setting it to AKTIV but unfortunately it doesn't do anything!

rubdom · 03-10-2011, 12:11 PM

Quote:

Originally Posted by spera23

I tried adding $302 to the VO and also found DWS in my CAPPL module. Tried setting it to AKTIV but unfortunately it doesn't do anything!

Do you have these anywhere:

QUITT_BLK_ENTSICHERN

QUITT_BLK_SICHERN

Seems "QUITT" has something to do with clown nose. "Sichern" means lock and "Entsichern" means unlock. So maybe these work. I only have these in my code car options.

AW128i · 03-10-2011, 12:18 PM

For those that have successfully added the OE alarm, can you detail what changes you made. I added $302 to the VO but the alarm isn't functioning. The clown nose does blink, but it did so before any coding changes were attempted.

spera23 · 03-10-2011, 12:21 PM

Quote:

Originally Posted by rubdom

Do you have these anywhere:

QUITT_BLK_ENTSICHERN

QUITT_BLK_SICHERN

Seems "QUITT" has something to do with clown nose. "Sichern" means lock and "Entsichern" means unlock. So maybe these work. I only have these in my code car options.

I have both in my FRM, but looks like they are already set to aktiv...

spera23 · 03-10-2011, 12:30 PM

Quote:

Originally Posted by spera23

I have both in my FRM, but looks like they are already set to aktiv...

I have something that looks likt LICHT_AN_LED which translates to LED light. Wonder what it could be...

03-10-2011, 08:01 AM	#2114
Pseudo Nim twinborific 118 Rep 4,836 Posts Drives: fast, sometimes slow Join Date: Nov 2008 Location: i am a citizen of the world iTrader: (9)	update - adding $481 (sport seats) didn't enable paddleshift. Grr. I guess i should take the wheel apart and test the paddles with a multimeter... __________________ Doko ni itemo, hito wa tsunagatte iru...
	Appreciate 0 Quote

03-10-2011, 08:44 AM	#2117
Pseudo Nim twinborific 118 Rep 4,836 Posts Drives: fast, sometimes slow Join Date: Nov 2008 Location: i am a citizen of the world iTrader: (9)	+1 - I wouldn't use "code car", ever. I dunno, it just sounds like a recipe for disaster unless proven otherwise. __________________ Doko ni itemo, hito wa tsunagatte iru...
	Appreciate 0 Quote

03-10-2011, 08:57 AM	#2118
E90PAT SOFLO CODING 199 Rep 3,587 Posts Drives: Z4M Join Date: Apr 2009 Location: SoFla iTrader: (18)	holy hell, they made this into better then a sticky!! they dedicated its own section now!
	Appreciate 0 Quote

03-10-2011, 08:59 AM	#2120
Pseudo Nim twinborific 118 Rep 4,836 Posts Drives: fast, sometimes slow Join Date: Nov 2008 Location: i am a citizen of the world iTrader: (9)	haha win! __________________ Doko ni itemo, hito wa tsunagatte iru...
	Appreciate 0 Quote

03-10-2011, 08:59 AM	#2121
Kalud Lieutenant 24 Rep 582 Posts Drives: e92 335i Join Date: Jun 2010 Location: Canada iTrader: (0)	Nice!
	Appreciate 0 Quote

03-10-2011, 09:16 AM	#2124
brinx38 Private 7 Rep 80 Posts Drives: SG E92 335i w/iDrive Join Date: Sep 2009 Location: N.Y. iTrader: (1) Garage List 2007 335i [0.00]	e90/e92 retrofitted CIC dump Hi, is there anyone (in US/Canada) with a retrofitted CIC? I would like to compare a dump of the trace file to diagnose a problem with my Bluetooth. It sorta half way connects.. I can dial from the phone and it plays thru' the car but the car says bluetooth is not connected, even though it shows the signal strength on the screen. can anyone help? Thanks.
	Appreciate 0 Quote

03-10-2011, 09:26 AM	#2125
BlaSTiWi Not new just quite 31 Rep 123 Posts Drives: E60, F30, G22 & G80 Join Date: Feb 2008 Location: Omaha, NE iTrader: (0) Garage List 2018 BMW 330i xDrive [0.00] 2007 BMW 525xi [0.00]	I thought I've seen it before but couldn't find it ... is there a function to prevent LCI AE from dimming or just make it stay at full voltage? Tkx!
	Appreciate 0 Quote

03-10-2011, 12:18 PM	#2132
AW128i Major 43 Rep 1,003 Posts Drives: E82 N51 Join Date: Nov 2010 Location: Southeastern, PA iTrader: (1)	For those that have successfully added the OE alarm, can you detail what changes you made. I added $302 to the VO but the alarm isn't functioning. The clown nose does blink, but it did so before any coding changes were attempted.
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search