|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
DIY- Trims wrap with CF fabric
|
|
11-13-2009, 10:26 AM | #155 |
aka Mike
106
Rep 1,395
Posts |
That trim he has pictured is different than the regular sport trim. I don't know about you, but mine has silver accent pieces on the sides. I'm 99% that the airbag has to be removed. Once you figure out where the slots are on the back of the wheel, removing the airbag is a snap. I didn't even have to disconect the wires to it.
|
Appreciate
0
|
11-13-2009, 03:20 PM | #156 |
Major General
219
Rep 8,375
Posts
Drives: Just a car
Join Date: Feb 2007
Location: CANADA eh!
|
|
Appreciate
0
|
11-14-2009, 01:24 AM | #157 |
Major General
422
Rep 8,004
Posts
Drives: '08 E90 335i, '99 E36 M3
Join Date: Apr 2009
Location: Houston, TX & Atlanta, GA
|
I've done it... http://www.e90post.com/forums/showthread.php?t=308728
|
Appreciate
0
|
11-22-2009, 05:56 PM | #159 |
Major General
219
Rep 8,375
Posts
Drives: Just a car
Join Date: Feb 2007
Location: CANADA eh!
|
|
Appreciate
0
|
11-23-2009, 09:52 AM | #160 |
Captain
36
Rep 927
Posts |
I have a couple spots that didn't stay tacked down, like around the vent opening and the ashtray opening. I can push them down, but it only stays for a couple hours. If I pull the pieces apart would I be able to repair that section, meaning would it be tacky or hardened?
__________________
Craig Brickner
Click to Join: BMWCCA # 366493 |
Appreciate
0
|
11-23-2009, 04:46 PM | #161 | |
Major General
219
Rep 8,375
Posts
Drives: Just a car
Join Date: Feb 2007
Location: CANADA eh!
|
Quote:
|
|
Appreciate
0
|
11-29-2009, 12:09 AM | #162 |
Private
17
Rep 63
Posts |
Need help guys, I really had a hard time with 1) upper clip of main vent , 2) the right hand side wire of AT..
1) I pried out the lower side of clips of main vent, for the uppers,,, the angle is just a bitch... I have no idea how to pry them out.. 2) From other thread someone said just left-right motion to set those plugs free, but for the right-hand-side one, it is located in opposite position and hard to leverage...(I broke little part of the edge of the plug...) |
Appreciate
0
|
11-29-2009, 04:13 AM | #163 | |
Private
17
Rep 63
Posts |
Quote:
|
|
Appreciate
0
|
11-29-2009, 08:30 AM | #164 |
Captain
36
Rep 927
Posts |
For the wires in the main section, I unhooked the harness to give a little more room to work on disconnecting the wires.
Ashtray lid? There's a good write up on just that task around here somewhere.
__________________
Craig Brickner
Click to Join: BMWCCA # 366493 |
Appreciate
0
|
11-30-2009, 04:36 PM | #165 |
Major General
219
Rep 8,375
Posts
Drives: Just a car
Join Date: Feb 2007
Location: CANADA eh!
|
See below link for the DIY ashtray lid. It will give you an idea where the tabs are. Good luck!
http://www.e90post.com/forums/showthread.php?t=186739 |
Appreciate
0
|
12-05-2009, 08:05 AM | #166 |
There I was balls deep in a...
29
Rep 1,470
Posts |
Soni I'm am after some of this I will drop you a PM!
__________________
BMW E90 320D Sapphire Black, Angel Eyes, BMW Performance Extras, Carbon Fabric Trim
|
Appreciate
0
|
12-09-2009, 12:00 PM | #168 |
There I was balls deep in a...
29
Rep 1,470
Posts |
Soni is best! I ordered some on Sunday and it arrived with me today! Thats USA to UK in three days! Top man!!!
__________________
BMW E90 320D Sapphire Black, Angel Eyes, BMW Performance Extras, Carbon Fabric Trim
|
Appreciate
0
|
12-10-2009, 11:39 AM | #169 |
Major General
219
Rep 8,375
Posts
Drives: Just a car
Join Date: Feb 2007
Location: CANADA eh!
|
|
Appreciate
0
|
12-10-2009, 01:19 PM | #170 |
There I was balls deep in a...
29
Rep 1,470
Posts |
Its hard as hell! I've started tonight but going to carry on tomorrow. How do you manage not to get the glue on the finished surface? I get it on my fingers and then onto there its a right pain!
__________________
BMW E90 320D Sapphire Black, Angel Eyes, BMW Performance Extras, Carbon Fabric Trim
|
Appreciate
0
|
12-10-2009, 01:28 PM | #171 | |
Brigadier General
118
Rep 3,432
Posts |
Quote:
PS...I'll need more fabrics after x-mas Soni |
|
Appreciate
0
|
12-10-2009, 08:45 PM | #172 |
Major General
219
Rep 8,375
Posts
Drives: Just a car
Join Date: Feb 2007
Location: CANADA eh!
|
|
Appreciate
0
|
12-10-2009, 08:47 PM | #173 |
Major General
219
Rep 8,375
Posts
Drives: Just a car
Join Date: Feb 2007
Location: CANADA eh!
|
Dont worry about getting the glue on the finished surface, after you finished, just use some alcohol and wipe the glue off and you are done.
|
Appreciate
0
|
12-10-2009, 09:39 PM | #174 |
Captain
36
Rep 927
Posts |
The stuff is amazingly resilient. Not sure how many times I've dumped coffee out of the joke of a cup holder onto the trim pieces. Wipes up with no issues as well.
__________________
Craig Brickner
Click to Join: BMWCCA # 366493 |
Appreciate
0
|
12-24-2009, 11:46 AM | #175 |
Major General
219
Rep 8,375
Posts
Drives: Just a car
Join Date: Feb 2007
Location: CANADA eh!
|
|
Appreciate
0
|
Bookmarks |
|
|