E90Post
 


TNT Racewerks
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > DIY Guides > Replaced my brake pads in my 335!



Reply
 
Thread Tools Search this Thread
      10-14-2010, 04:55 AM   #133
boleneger
New Member
boleneger's Avatar
Greece
1
Rep
11
Posts

Drives: e90 320i
Join Date: Dec 2008
Location: GREECE-MACEDONIA-THESSALONIKI

iTrader: (0)

Hi I have replaced my rear brake pads in my 320i. My rears are a little different than in bigger 3ers. I have a single rotor non ventilated and a caliper as you can see in here
http://www.realoem.com/bmw/showparts...77&hg=34&fg=10
So I bought the textar pads 50euros plus a sensor 15euros. In pads set is everything you need the pads ,the sliders (number 8) and two bolts (the number 3 in the diagram).
So I removed the downside 3 bolt and rotated the caliper without moving the base and free the pads.
The most difficult part was to place the sensor on the pad. I was trying for an hour but the f@ckin thing did not want to seat properly. It needs the right angle and not too much force. Finally it fitted properly after much cursing .
Hope I help someone with my experience.
__________________
Appreciate 0
      11-06-2010, 01:55 PM   #134
hookah66
dirigir é a minha paixão
hookah66's Avatar
United_States
4
Rep
153
Posts

Drives: e93 328c N52 3.0L cabriolet
Join Date: Jul 2010
Location: somewhere called Boonton USA

iTrader: (0)

Garage List
2002 325xi  [0.00]
2009 328i cabriolet  [0.00]
Kudos to Mr.5 for a fantastic write up. Just did my rear pads (waiting for my fronts) on my '09 e93 and here are my two cent contribution:
I am a 62 years old fart and I did it in one hour 15 min, if I managed it you certainly can do it. I used simple tools: you need a 7 mm Allen 3/8 socket, small & big pliers, small hammer, flat head screw driver, 17 mm 1/2 inch socket for wheel lugs and a torque wrench. For supplies I used ordinary Centric posiQuiet semi metallic, synthetic high temp brake grease and non chlorinated brake cleaner, one can per wheel. Spray clean the calipers and the rubber of the piston prior to pushing in the piston. Open the fluid reservoir. Use light hammer to gently tap the spring back into the slot of the floating caliper. Did not and do not recommend taking the carrier part out of wheel hub unless you are also replacing rotor. Look carefully for the shiny worn parts of the old pads, and only dab those points of contact with the high temp synt brake grease on the new pads. DO NOT USE any gluey stuff such as CRC or Permatex. German floating calipers are not designed for that, note that the oem pads are NOT COATED with that gluey gunk. NEVER use any anti-seize compounds on the threads of high tensile bolts (bmw oem bolts are rated high tensile strength), otherwise you will induce "creeping" and premature failure of the bolt will occur. Be careful to lubricate the shafts of the shear pins only, but not the thread part. Looks like the shear pins threads were coated with LocTite. Watch out for the brake sensor (passenger side) it got a tiny small metal clip that can get twisted or snapped off. Otherwise just follow the instructions as posted by Mr.5. I only removed the shear pins of the floating calipers not the 16mm high tensile bolts of the carrier part. The Centric posiQuiet pads are so smooth compared to the OEM pads, now my bimmer glides to a velvety stop. No squeaks at all. You must immediately "bed in" the new pads. Have fun.
Attached Images
      
__________________

Sou fanático por conversíveis...

Last edited by hookah66; 11-06-2010 at 02:17 PM..
Appreciate 0
      11-08-2010, 01:58 PM   #135
dc5_champ88
Captain
dc5_champ88's Avatar
24
Rep
666
Posts

Drives: 2007 BMW 335i
Join Date: Oct 2010
Location: Maryland

iTrader: (5)

Garage List
2007 BMW 335i  [0.00]
Excellent Diy
__________________
Current: 07 e92 335i: JB4, AA Catless DP, Big Tom FMIC, CP-e Full Exhaust, Injen Intake, Type-S BOV, Meth

Previous: 03 Acura RSX-S: Boosted 400WHP (SOLD)
Appreciate 0
      07-12-2011, 04:46 PM   #136
turb0junkie
New Member
0
Rep
5
Posts

Drives: 2007 Black Sapphire 335i
Join Date: Jun 2011
Location: New Orleans

iTrader: (0)

Quote:
Originally Posted by Lagger1 View Post
Just finished my rears. Simple

My only feedback is to grease your sliding pins. I was metal-to-metal on one side cause some bmw tech was too lazy to do this. Neither the clip or sensor picked up on this.

+1 on the sliding pins
Appreciate 0
      08-29-2011, 09:14 PM   #137
CLE-335
Private
CLE-335's Avatar
4
Rep
52
Posts

Drives: 2k8 335xi Sedan
Join Date: Aug 2011
Location: Cleveland Ohio

iTrader: (3)

Fantastic post. Glad I skipped the maint plan on my CPO 335!

Last edited by CLE-335; 10-24-2011 at 07:24 PM..
Appreciate 0
      10-08-2011, 10:03 AM   #138
Supra98
Private First Class
1
Rep
141
Posts

Drives: BMW
Join Date: Sep 2011
Location: Ohio

iTrader: (1)

I'm just going to be putting some crc brake quiet on the pads. I won't need to compress the piston since i'm putting the old pads back on right?
Appreciate 0
      10-13-2011, 02:20 PM   #139
jeffvb9
Lieutenant
28
Rep
425
Posts

Drives: 2022 BMW x4m comp
Join Date: Nov 2008
Location: Kansas City

iTrader: (3)

Quote:
Originally Posted by Supra98 View Post
I'm just going to be putting some crc brake quiet on the pads. I won't need to compress the piston since i'm putting the old pads back on right?
Do not put CRC brake quiet on these pads....pls read the post 2 up from here.
Appreciate 0
      10-17-2011, 02:49 AM   #140
lifeisgood
New Member
0
Rep
19
Posts

Drives: E90
Join Date: Oct 2011
Location: Socal

iTrader: (0)

Tremendously useful! Just did mine today! I got 2 brand new brake pads and rotors in the front! Thank you again!
Appreciate 0
      11-10-2011, 07:08 PM   #141
cj79330i
New Member
1
Rep
10
Posts

Drives: 2006 330i metallic graphite
Join Date: Oct 2009
Location: South San Francisco

iTrader: (0)

I did diy front brake pads. After the rapair including sensor, the light will not reset on my dashboard. I tried it so many times to reset it but still will not do it.
Appreciate 0
      11-16-2011, 08:37 PM   #142
cj79330i
New Member
1
Rep
10
Posts

Drives: 2006 330i metallic graphite
Join Date: Oct 2009
Location: South San Francisco

iTrader: (0)

I did diy front brake pads replacement including sensor on my 2006 330i sport sedan, after all it's done brake light warning on my dassboard will not reset. I tried so many attempt to reset it still will not do it. Any comments?
Appreciate 0
      01-06-2012, 03:14 PM   #143
pharmboyrx
New Member
0
Rep
11
Posts

Drives: 2006 330i
Join Date: Mar 2011
Location: Florida

iTrader: (0)

I'm planning on doing my F & R pads and rotors tomorrow. I noticed nobody mentioned bleeding the brakes. I just changed my brake fluid a couple of months ago so I won't be doing it with this job. As long as I keep the level appropriately high in the reservoir, will I be able to avoid this step? I won't have help and I don't have a pressure bleeder available.
Appreciate 0
      02-02-2012, 10:33 AM   #144
Lozzatron
New Member
United Kingdom
2
Rep
19
Posts

Drives: E92
Join Date: Feb 2012
Location: North Wales, UK

iTrader: (0)

awesome thread will remember to bed my brakes
Appreciate 0
      02-11-2012, 06:45 PM   #145
Cbozz
Colonel
Cbozz's Avatar
United_States
677
Rep
2,712
Posts

Drives: M3
Join Date: Feb 2012
Location: South Florida/ St. Louis

iTrader: (27)

Garage List
Did you replace the rotor too? How did you measure it?
Appreciate 0
      03-15-2012, 11:45 AM   #146
hookah66
dirigir é a minha paixão
hookah66's Avatar
United_States
4
Rep
153
Posts

Drives: e93 328c N52 3.0L cabriolet
Join Date: Jul 2010
Location: somewhere called Boonton USA

iTrader: (0)

Garage List
2002 325xi  [0.00]
2009 328i cabriolet  [0.00]
just changed to AKEBONO EURO CERAMIC PADS

This is my fourth set of pad replacement, I got about 32K miles... and so far it has been the best replacemet!!! Very low dust, extremely quiet and ultra smooth. Good stopping and no fading. I am very happy... finally it is braking better than the OEM without the dust. I yanked out the ATE OEM pads at around 5K miles due to its annoying black dust. Replaced with ultra high performance EBC Red which was not suitable for every day driving and VERY loud squeaks when cold. Changed to Centric PosiQuiet semi metallic, which were low dust but stopping distance was not par with the OEM ATE's. I read about Akebono's but could not find the correct stock for the e93 larger front calipers last year, but now I got discounted from Tire Rack which fits the larger floating front calipers of e93 series. The Akebono's are so far the best made replacement pads with integrally mounted fabric anti rattling shims in the inner front pads. Also the cut outs for the brake sensors are a perfect fit. The high temperature anti rattling grease that comes with the kit is a must. The sensor snaps in without any damages, unlike the EBC which I had to replace with new sensors. The Centric PosiQuiet were low dust, so this time around the calipers were a lot cleaner than when I had the OEM ATE's. I definitely recommend these pads for e93 series bimmers.
__________________

Sou fanático por conversíveis...

Last edited by hookah66; 03-15-2012 at 11:56 AM..
Appreciate 0
      05-08-2012, 11:00 PM   #147
335i101
Lieutenant
335i101's Avatar
United_States
79
Rep
586
Posts

Drives: 2008 E60 M5
Join Date: Dec 2010
Location: ND

iTrader: (2)

So, I am guessing you changed pads for dust/performance/squeal reasons.

Maybe I am mistaken, but if people are replacing pads cuz they are worn, they should replace the rotors as well, correct??

Can't resurface our rotors
__________________
2021 Mercedes G550
2015 X5M
2020 Supra-JB4, DP
2008 M5 with muffler delete-sold
2007 650i-sold
2008 335i-JB4, DP, Meth-sold
Appreciate 0
      05-14-2012, 07:18 PM   #148
lux.sh
missing two turbos.
lux.sh's Avatar
United_States
574
Rep
4,859
Posts

Drives: fast around corners.
Join Date: Sep 2005
Location: Curves

iTrader: (12)

Garage List
Can anyone confirm if this DIY can be used for 2006 E90 330i sedan? I assume its very similar..
__________________
06 AW E90 330i ZPP/ZSP/Step/Expired Warranty

: Prior Design Front : ACS Rear : ACS Roof : BlackLines : Simota Intake : Carbon Fiber Interior Trim :
: MTEC V3 : 24% Charcoal : V1 Hardwired : Solaris Invisibulbs/LED interior :
Appreciate 0
      07-13-2012, 05:22 PM   #149
Tate325xi
New Member
0
Rep
6
Posts

Drives: 2006 325xi
Join Date: Jun 2012
Location: Denver, CO

iTrader: (0)

How hard is it to remove the caliper bolts? I am trying with a 3/8 socket wrench and am having a helluva time. I applied PB Blaster without any avail, do I have to buy a breaker bar?
Appreciate 0
      07-14-2012, 10:50 AM   #150
hookah66
dirigir é a minha paixão
hookah66's Avatar
United_States
4
Rep
153
Posts

Drives: e93 328c N52 3.0L cabriolet
Join Date: Jul 2010
Location: somewhere called Boonton USA

iTrader: (0)

Garage List
2002 325xi  [0.00]
2009 328i cabriolet  [0.00]
bmw Ate OEM floating calipers ...

From my limited knowledge, I do not see any major changes in the configuration of the Ate floating calipers. From my 2002 e46 328xi to 2009 e93 328i convertible, the basic set up of the floating calipers, the rotor and the pads are identical. Just make sure the parts are specific to your built year, there is major variations between the production lines. So you must to furnish your VIN number prior to ordering any brake components. The bolts that retain the floating calipers require good torque to loose them, you must do on a lift in order to get the appropriate leverage, and make sure you torque back to the spec's without any anti-sizing compounds, for these are high tensile bolts. The rotors are designed for eazy pop out for they are retained with just one single torx. I guess it is common practice to change the rotors for those who track. You do not have to change the rotors if it is not scoured, not pitted or uneven worn. Mine are approaching 47K and I do not get any fluttering or shimmering at all. You need at least a 1/2 socket drive with deep sockets whenever working on any of undercarriage components. A 3/8 drive socket will not give you enough force to loosen high tensile bolts.
__________________

Sou fanático por conversíveis...

Last edited by hookah66; 07-14-2012 at 11:00 AM..
Appreciate 0
      07-16-2012, 12:24 AM   #151
Tate325xi
New Member
0
Rep
6
Posts

Drives: 2006 325xi
Join Date: Jun 2012
Location: Denver, CO

iTrader: (0)

Quote:
Originally Posted by hookah66 View Post
From my limited knowledge, I do not see any major changes in the configuration of the Ate floating calipers. From my 2002 e46 328xi to 2009 e93 328i convertible, the basic set up of the floating calipers, the rotor and the pads are identical.
The E46 328 was never built in xi configuration, and the 328 was discontinued before MY 2002...
Appreciate 0
      07-16-2012, 08:03 AM   #152
hookah66
dirigir é a minha paixão
hookah66's Avatar
United_States
4
Rep
153
Posts

Drives: e93 328c N52 3.0L cabriolet
Join Date: Jul 2010
Location: somewhere called Boonton USA

iTrader: (0)

Garage List
2002 325xi  [0.00]
2009 328i cabriolet  [0.00]
Quote:
Originally Posted by Tate325xi View Post
The E46 328 was never built in xi configuration, and the 328 was discontinued before MY 2002...
you stand correct... it was a e46 325xi
__________________

Sou fanático por conversíveis...
Appreciate 0
      07-17-2012, 07:34 AM   #153
omerfar23
First Lieutenant
United_States
19
Rep
379
Posts

Drives: 2011 E93 335i, 2008 335i e92
Join Date: May 2007
Location: Baltimore, MD

iTrader: (0)

do you open the master brake reservoir under the hood before you start the job?
__________________
********** 2008 BMW 335i TT******
Appreciate 0
      07-17-2012, 02:03 PM   #154
hookah66
dirigir é a minha paixão
hookah66's Avatar
United_States
4
Rep
153
Posts

Drives: e93 328c N52 3.0L cabriolet
Join Date: Jul 2010
Location: somewhere called Boonton USA

iTrader: (0)

Garage List
2002 325xi  [0.00]
2009 328i cabriolet  [0.00]
helps to open main reservoir

Yes, it definitely helps to evacuate little bit of hydraulic fluid as to prevent spillage when you "squeeze" the pads in to facilitate its removal from the calipers.
__________________

Sou fanático por conversíveis...
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 02:51 PM.




e90post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST