|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
VIN is faulty error in NCS-Expert
|
|
04-16-2014, 09:51 AM | #1 |
Second Lieutenant
12
Rep 224
Posts |
VIN is faulty error in NCS-Expert
Long story short, inpa and WinKFP are working (did the alpina flash), but when I try to use ncs to reset the battery, I get a vin is faulty error. When I try to change it, it brings up my actual VIN, but with an extra 4 on the end. Any ideas?
I did a search and most people have said to upgrade the software, but I have to the most updated that I can find. Thanks, Bryan
__________________
2009 BSM E92 AT 335i - RB Turbos - MMP Inlets - AA Race FMIC - AP DPs - KW V1s - RB PCV - N20 MAP - Rotora Forged BBK - VRSF CP w/ Tial BOV - Fuel It Stage 2 LPFP - Alpina TCU Flash
|
04-16-2014, 01:46 PM | #2 |
Captain
93
Rep 713
Posts |
If you have Standard tools 2.12 you are fine.
Check if you have E89 folder in C:\NCSEXPERT\DATEN\ And make sure that you copied all files from sp-daten\daten\*.* to here C:\NCSEXPERT\DATEN\ and here C:\NCSEXPERT\DATEN\E89 Just recopy this and check if this helps |
Appreciate
0
|
04-16-2014, 01:51 PM | #3 |
Second Lieutenant
12
Rep 224
Posts |
It was 2.12 that I installed.
I know I copied the sp-daten\daten files to ncsexpert\daten\ but I am not sure if I copied them to ncsexpert\daten\E89. I'll have to double check. Just to verify what you are saying, you mean to copy the same \daten files to those two different folders or daten to daten and e89 to e89? Thanks
__________________
2009 BSM E92 AT 335i - RB Turbos - MMP Inlets - AA Race FMIC - AP DPs - KW V1s - RB PCV - N20 MAP - Rotora Forged BBK - VRSF CP w/ Tial BOV - Fuel It Stage 2 LPFP - Alpina TCU Flash
|
Appreciate
0
|
04-16-2014, 02:36 PM | #4 |
Banned
16
Rep 128
Posts |
this is how you update new daten files...
so copy the files and replace Target ---------------------------Source .(SP-Daten-Exx directory ) \NCSEXPER\SGDAT\ -------- .ipo files \NCSEXPER\DATEN\ -------- coding data (daten) for models \EDIABAS\Ecu\ -------------- .prg files...... |
Appreciate
1
EIVAZ0.00 |
04-16-2014, 03:04 PM | #6 |
Second Lieutenant
12
Rep 224
Posts |
Fairly certain I did that. It was in one of the DIY setup guides I went through, but I will do again to be absolutely certain! Thanks :-)
__________________
2009 BSM E92 AT 335i - RB Turbos - MMP Inlets - AA Race FMIC - AP DPs - KW V1s - RB PCV - N20 MAP - Rotora Forged BBK - VRSF CP w/ Tial BOV - Fuel It Stage 2 LPFP - Alpina TCU Flash
|
Appreciate
0
|
04-16-2014, 05:19 PM | #7 | |
Second Lieutenant
12
Rep 224
Posts |
Quote:
I am following the steps in the register battery DIY thread. I open NCS-Expert, Select a profile, Press F1 (VIN/ZCS/FA), Press F3 (CS/FA f. EC) > Select E89 > Click OK > Select CAS, and this is when it occurs. The steps to that procedure are here in post 35. Any other ideas?
__________________
2009 BSM E92 AT 335i - RB Turbos - MMP Inlets - AA Race FMIC - AP DPs - KW V1s - RB PCV - N20 MAP - Rotora Forged BBK - VRSF CP w/ Tial BOV - Fuel It Stage 2 LPFP - Alpina TCU Flash
|
|
Appreciate
0
|
04-16-2014, 05:21 PM | #8 | |
Banned
16
Rep 128
Posts |
Quote:
|
|
Appreciate
1
KevinWaterloo7.50 |
04-16-2014, 05:39 PM | #9 | |
Second Lieutenant
12
Rep 224
Posts |
Quote:
What does that file do? Thanks for all the help.
__________________
2009 BSM E92 AT 335i - RB Turbos - MMP Inlets - AA Race FMIC - AP DPs - KW V1s - RB PCV - N20 MAP - Rotora Forged BBK - VRSF CP w/ Tial BOV - Fuel It Stage 2 LPFP - Alpina TCU Flash
|
|
Appreciate
0
|
04-16-2014, 05:44 PM | #10 | |
Banned
16
Rep 128
Posts |
Quote:
FSW_PSW (MAN) FSW_PSW (TRC) INSIDE THE (MAN) ONE DELETE ALL THE VALUES INSIDE THEN SAVE AS.MAN SO FSW_PSW.MAN MAKE SURE SAVE AS ALL FILES OTHERWISE IT WOULD SAVE ONLY AS PLAIN TEXT. |
|
Appreciate
0
|
04-16-2014, 06:15 PM | #12 | |
Second Lieutenant
12
Rep 224
Posts |
Quote:
Thanks.
__________________
2009 BSM E92 AT 335i - RB Turbos - MMP Inlets - AA Race FMIC - AP DPs - KW V1s - RB PCV - N20 MAP - Rotora Forged BBK - VRSF CP w/ Tial BOV - Fuel It Stage 2 LPFP - Alpina TCU Flash
|
|
Appreciate
0
|
04-16-2014, 06:23 PM | #13 | |
Banned
29
Rep 240
Posts |
Quote:
|
|
Appreciate
0
|
04-16-2014, 07:54 PM | #14 | ||
Second Lieutenant
12
Rep 224
Posts |
Quote:
__________________
2009 BSM E92 AT 335i - RB Turbos - MMP Inlets - AA Race FMIC - AP DPs - KW V1s - RB PCV - N20 MAP - Rotora Forged BBK - VRSF CP w/ Tial BOV - Fuel It Stage 2 LPFP - Alpina TCU Flash
|
||
Appreciate
0
|
04-17-2014, 09:03 AM | #15 |
Second Lieutenant
12
Rep 224
Posts |
You are the man Joe, that worked and the steps in NCS worked just as the other post explained, made it through all of them without a hitch. Now when I run the job to register the battery in Ediabas, I get an invalid ECU error. I will upload the image later when I get home from work, I can't do it from my work computer.
__________________
2009 BSM E92 AT 335i - RB Turbos - MMP Inlets - AA Race FMIC - AP DPs - KW V1s - RB PCV - N20 MAP - Rotora Forged BBK - VRSF CP w/ Tial BOV - Fuel It Stage 2 LPFP - Alpina TCU Flash
|
Appreciate
0
|
04-17-2014, 11:01 AM | #16 | |
Banned
16
Rep 128
Posts |
Quote:
you can do the following copy-paste procedure: Target ---------------------------Source .(SP-Daten-Exx directory ) \NCSEXPER\SGDAT\ -------- .ipo files \NCSEXPER\DATEN\ -------- coding data (daten) for models \EDIABAS\Ecu\ -------------- .prg files...... |
|
Appreciate
0
|
04-20-2014, 07:17 PM | #17 |
Lieutenant
25
Rep 432
Posts
Drives: 2017 BMW M3
Join Date: Mar 2013
Location: Sherwood, OR
|
I'm having the same issue and have a JB4. Do you just mean put it to Map 0?
__________________
2017 M3 - Long Beach Blue, Competition Package, Burger Performance Intake
2009 135i - Dinan CAI, Dinan Exhaust, Turbonetics FMIC, Dinan Stage 2 |
Appreciate
0
|
04-20-2014, 09:06 PM | #18 |
packet jockey
16
Rep 299
Posts |
I've seen the exact same error on a friend's car I was coding. Without knowing much about the JB4 I don't know if he went to map 0 or if there is a separate "off", but that resolved the problem.
__________________
2011 335d
With great torque comes great responsibility |
Appreciate
0
|
04-21-2014, 11:45 AM | #20 |
Lieutenant
25
Rep 432
Posts
Drives: 2017 BMW M3
Join Date: Mar 2013
Location: Sherwood, OR
|
Thanks. I put it to Map 0 and am now getting a different error.
Datatransmission to ECU distrubed IFH-0010 Thanks!
__________________
2017 M3 - Long Beach Blue, Competition Package, Burger Performance Intake
2009 135i - Dinan CAI, Dinan Exhaust, Turbonetics FMIC, Dinan Stage 2 |
Appreciate
0
|
04-21-2014, 12:29 PM | #21 |
Banned
29
Rep 240
Posts |
|
Appreciate
0
|
04-21-2014, 12:54 PM | #22 |
Lieutenant
25
Rep 432
Posts
Drives: 2017 BMW M3
Join Date: Mar 2013
Location: Sherwood, OR
|
I guess I'm assuming putting it to map 0 is "turning it off"...
__________________
2017 M3 - Long Beach Blue, Competition Package, Burger Performance Intake
2009 135i - Dinan CAI, Dinan Exhaust, Turbonetics FMIC, Dinan Stage 2 |
Appreciate
0
|
Bookmarks |
|
|