|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Fair quote? for installs and dyno time
|
|
12-30-2014, 06:35 PM | #1 |
Captain
62
Rep 954
Posts |
Fair quote? for installs and dyno time
2 hours on the dyno for remote PID tuning
VTT 2+ install Transmission swap/pan Custom turbo inlet plumbing install Custom Oilcooler retrofit and install Water pump and Tstat $3200 after tax. Seems steep i know but this is basically 4 days of work (shop hours) these guys know their shit. they work with MOTIV and OveRev Anyhow i know i know i should do it and i probably could but i am going to san diego for 8 weeks in a few days and when i get back i wont have time before i move again. what do you all think?
__________________
cp-e GTX3071R TT kit, cp-e quad exhaust, cp-e fuelbar, Stage 3 LPFP+lines, AEM EFI, Custom Meth kit, Apex EC7 18s w/R888 295s, Stoptech, M3 front, m-sport rear, cp-e difuser, Custom Headlights, CFS Radiator, Custom OC, 1000hp Lvl10 trans, DSS Axles, MFactory LSD, DEFIV lockdown kit, M3 refresh kit, KWv2's, cp-e project "4doorbmwpower"
|
12-30-2014, 06:41 PM | #2 |
Private
12
Rep 58
Posts |
That's seems very reasonable to me given the amount of work. Figure a typical trans swap is 1k and water pump and t stat can almost run the same not bad at all.
What trans are you going with an updated one for the alpina flash? |
Appreciate
0
|
12-30-2014, 06:45 PM | #3 |
Captain
62
Rep 954
Posts |
yes in my sig.. just an 08 tranny. with some level 10 parts to tighten it up before i swap the rear end. i know i should have n LSD already but hey. next on the chopping block after LPFP is going to be full M3 suspension axles out and LSD.
__________________
cp-e GTX3071R TT kit, cp-e quad exhaust, cp-e fuelbar, Stage 3 LPFP+lines, AEM EFI, Custom Meth kit, Apex EC7 18s w/R888 295s, Stoptech, M3 front, m-sport rear, cp-e difuser, Custom Headlights, CFS Radiator, Custom OC, 1000hp Lvl10 trans, DSS Axles, MFactory LSD, DEFIV lockdown kit, M3 refresh kit, KWv2's, cp-e project "4doorbmwpower"
|
Appreciate
0
|
12-31-2014, 07:58 AM | #6 |
Major General
2041
Rep 6,104
Posts |
Sounds legit.
__________________
When you say impact instead of affect/effect, you are communicating that you don't understand the difference between the two words, and are too lazy to learn.
|
Appreciate
0
|
12-31-2014, 10:30 AM | #7 |
4493
Rep 1,862
Posts
Drives: powered by bootmod3
Join Date: Oct 2014
Location: www.protuningfreaks.com | www.bootmod3.com
|
Turbos, intakes, water pump and thermostat are done in one go and shouldn't take more than 12 hours at the most to do. At a shop that has done N54 turbo swaps before its about an 8-9 hour job.
That leaves you with the transmission swap/pan. What does that mean exactly? What sort of oil cooler are you putting in? This might be a good chunk of your cost depending on what you're doing and what parts you're sourcing and from where. If the car will spend 99% of the time on the street, which most N54s do, and you don't have an oil cooler at all just add an OEM one and be done with it. People go overboard with oil coolers for street driven N54s, I see it all the time, useless investment in vast majority of cases.
__________________
YouTube Channel [NEW] | Facebook User Group (20,000+ members) | Tech Support Website | Wiki | FAQ | iOS App | Android App | bootmod3 Web
Sales Support Email: sales@protuningfreaks.com | Tech Support Email: support@protuningfreaks.com |
Appreciate
0
|
12-31-2014, 10:33 AM | #8 |
Captain
62
Rep 954
Posts |
putting a new tranny in and im having them swap out the tranny pan. (not a big deal) but i thru it on there anyhow cause adding the 10L of tranny fluid does actually take a while on this car haha.
I am having them custom make on of my 25 row core and braided steel lines swapping out the Oil filter housing and putting one of Robs block off plates on it. not gonna run a Tstat.
__________________
cp-e GTX3071R TT kit, cp-e quad exhaust, cp-e fuelbar, Stage 3 LPFP+lines, AEM EFI, Custom Meth kit, Apex EC7 18s w/R888 295s, Stoptech, M3 front, m-sport rear, cp-e difuser, Custom Headlights, CFS Radiator, Custom OC, 1000hp Lvl10 trans, DSS Axles, MFactory LSD, DEFIV lockdown kit, M3 refresh kit, KWv2's, cp-e project "4doorbmwpower"
|
Appreciate
0
|
12-31-2014, 10:34 AM | #9 | |
Captain
62
Rep 954
Posts |
Quote:
Yeah i love those guys, just making sure i am not overshooting something.
__________________
cp-e GTX3071R TT kit, cp-e quad exhaust, cp-e fuelbar, Stage 3 LPFP+lines, AEM EFI, Custom Meth kit, Apex EC7 18s w/R888 295s, Stoptech, M3 front, m-sport rear, cp-e difuser, Custom Headlights, CFS Radiator, Custom OC, 1000hp Lvl10 trans, DSS Axles, MFactory LSD, DEFIV lockdown kit, M3 refresh kit, KWv2's, cp-e project "4doorbmwpower"
|
|
Appreciate
0
|
12-31-2014, 10:37 AM | #10 | |
Captain
62
Rep 954
Posts |
further explanation on INLETs
Quote:
__________________
cp-e GTX3071R TT kit, cp-e quad exhaust, cp-e fuelbar, Stage 3 LPFP+lines, AEM EFI, Custom Meth kit, Apex EC7 18s w/R888 295s, Stoptech, M3 front, m-sport rear, cp-e difuser, Custom Headlights, CFS Radiator, Custom OC, 1000hp Lvl10 trans, DSS Axles, MFactory LSD, DEFIV lockdown kit, M3 refresh kit, KWv2's, cp-e project "4doorbmwpower"
|
|
Appreciate
0
|
12-31-2014, 10:40 AM | #11 |
4493
Rep 1,862
Posts
Drives: powered by bootmod3
Join Date: Oct 2014
Location: www.protuningfreaks.com | www.bootmod3.com
|
Given all the custom fab work in that case you got yourself a deal.
__________________
YouTube Channel [NEW] | Facebook User Group (20,000+ members) | Tech Support Website | Wiki | FAQ | iOS App | Android App | bootmod3 Web
Sales Support Email: sales@protuningfreaks.com | Tech Support Email: support@protuningfreaks.com |
Appreciate
0
|
Bookmarks |
|
|