|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
Help Please. JB4
|
|
11-27-2012, 05:43 PM | #1 |
Private
9
Rep 87
Posts |
Help Please. JB4
Current Mods
JB4 G5 board DCI Catless downpipe Muffler delete Charge Pipe w BOV So i have a local muffler shop install my Catless downpipe and when they did they crossed the O2 sensors. as may of you know the car throws a code and starts running incredibly rough with this I had the o2 sensors put back correctly and the car still doesnt run right ONLY WITH THE JB4 (any map it does the same thing) with the JB4 off, the car runs great (throws a CEL i am assuming bc the catless dp) but runs great, slow but great As soon as i up the JB4 on the CELS go away, and once the car goes into full boost, the car starts shaking and throws another cel. This happens on any map Any ideas? the car is at TKX currently and they are waiting for someone to come down and read the code |
11-27-2012, 05:51 PM | #3 |
Private
9
Rep 87
Posts |
|
Appreciate
0
|
11-27-2012, 08:11 PM | #5 |
Second Lieutenant
9
Rep 255
Posts |
Definitely sounds like a misfire.. When adding lbs of boost, parts that would often need to be replaced, because they were already on their way out. Try spark plugs first. Then ignition coils. If neither of these two then high pressure fuel pump or injectors. How smooth does your car idle? If rough than you might want to clean your intake valves.
__________________
2007 BSM 335i ZSP/ZPP l JB4 G5 ISO l E85 l BMS FLASH l METH l DCI l DPs l Twin BOVs l Scoops l 18" Forgestar F14sl Koni Yellows l Swift Spec-R l GForce Rivals/Slicks l Quaife LSD Last edited by Exzackt; 11-27-2012 at 09:47 PM.. |
Appreciate
0
|
11-27-2012, 11:55 PM | #6 |
ex deus machina
123
Rep 968
Posts |
I would like some clarification,
- The car had a JB4 installed and was running ok -after downpipes install with incorrect O2’s runs bad -O2 sensors corrected but still runs bad (how was it discovered that the O2 sensors were switched, it’s possible they were damaged and now need replacement) You might need to do a hard rest of the DME by unplugging the battery overnight
__________________
Daily: G30 M550i, Bluestone, JB4, 1 step colder plugs, 6WB retrofit
Winter Beast: Audi S4 4.2L V8, Supercharger, brakes, suspension & exhaust mods Wifes': F15 M50d clone, DUDMD tune, WMI, MPBK Gone: E92 335i N54 468rwtq |
Appreciate
0
|
11-28-2012, 10:47 AM | #7 | |
Private
9
Rep 87
Posts |
Quote:
-correct -I went to autocature in NJ and they check the code and corrected the issue (the car ran fine with the jb4 off after this as prior the car ran like shit constantly) I might add that it doesnt happen EVERY pull... id say 98% of the time i am thinking it either Bad o2 sensors from when they were switched (idk if they go bad) or plugs and or coils. Car has 45k on it and im sure were never changed (bought it used) |
|
Appreciate
0
|
11-28-2012, 10:56 AM | #9 |
GoofBall
50
Rep 1,055
Posts |
First you can reset all learned values by using Category 1 selection 7 will clear adaptations. Try that bcuase you might not be fueling properly due the air amounts. Are you 100% sure the 02's are in the right place. Turn off the Autoclear Check light codes. If you dont know if you have it on go to screen 1 and use option 4 and get out of the menu as normal when you use the track down button on your steering wheel.
Car idle do the 1/7 clear adaptations let it idle for a little bit. Go to map 4, which is factory boost but allows the JB4 to keep track of codes and such. Drive the car 10 miles, some boost some without. From there go to map 5 and drive again. If your still getting a stumble use the JB4 to figure out what codes. If it throws a code, use the JB4 to figure out what it did and why. If its a missfire use the cable to see what your long term and short term fuel trims are. As well note which cylinder the missfire was on. Report back when your done. |
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|