E90Post
 


Extreme Powerhouse
 
BMW 3-Series (E90 E92) Forum > E90 / E92 / E93 3-series Technical Forums > DIY Guides > DIY: Backup Hood Release



Reply
 
Thread Tools Search this Thread
      01-17-2016, 12:40 AM   #1
Figure807
Power without control is no power at all...
Figure807's Avatar
United_States
15
Rep
190
Posts

Drives: 335i 6spd Blk/Blk
Join Date: Oct 2009
Location: Honolulu, Hawaii

iTrader: (1)

DIY: Backup Hood Release

Time required: ~10 minutes or less
Skills required: knot tying, fine motor skills
Tools needed: flashlight, needlenose pliers
Parts needed: 2x ~2ft long pieces of wire

Backstory: I was cruising along one day when my car (2009 e92 335i) let me know that I needed to add a quart of oil - I keep an extra in my trunk as I'm sure most of you do. Well, imagine my surprise when I pulled the hood release and only the driver's side latch popped . No amount of pulling or pushing on the passenger side could get the latch to pop. I Googled for a solution but the only thing I could find that might be helpful was a YouTube video of a guy using a long bent flat head to pop the latch from behind the kidney grille. If you have the ability to blindly actuate the latches like that guy did, kudos, otherwise the latches are essentially sealed off. So I put the car on a lift and proceeded to disassemble the front end to find a solution. After two hours of fruitless effort, I put the car back together and decided to try again another day. However, before heading home I tried the hood release one more time and it worked! Realizing that I could have this problem again, I needed to figure out an alternate way to releasing the latches. Before I closed the hood, I sprayed the latches down with silicone lube just in case that had been the issue (it wasn't - I need to replace the cable).

1. I decided to position a backup wire to actuate the latches in the event that the hood release cable failed again (it did a few days later). Below is a picture of the passenger's side latch and the hood release cable with ball end.


2. Obtain two pieces of wire, ~2ft long. I had leftover wire from another project so I used that. You will need to tie an knot at one end of each wire - I chose to do an overhand knot but I imagine any compact knot will do.


3. Use pliers to tighten the knot.


4. Route the backup wire.


5. Ensure that the backup wire moves freely.


6. Position the knotted end on top of the hood release cable.


7. After the wire has been routed and positioned properly, you can tie a loop at one end. Engage the latch using a screwdriver and then pull on the backup wire to ensure that it works.


8. After you have successfully tested the backup wire, positioned the looped end so that it dangles near the wheel well liner.
Note: This is a picture of the driver's side.


9. Relatively easy access from the wheel well. Wrap the loop with something bright for better visibility if you didn't use white wire. Blue painter's tape maybe.


10. Enjoy your piece of mind
__________________
2009 335i Coupe 6MT Blk Sapphire / Blk Leather
2007 328i Coupe 6MT Blk Sapphire / Blk Leather *Sold
1985 Toyota Corolla GTS 5MT 1.5-way Slvr / Blk *Sold
1987 Toyota Corolla GTS 5MT KAAZ 2-way Blk / Blk *Sold

Last edited by Figure807; 01-17-2016 at 01:43 AM..
Appreciate 0
      01-28-2016, 05:23 AM   #2
Vish8895
Captain
Vish8895's Avatar
United Kingdom
73
Rep
641
Posts

Drives: E92 M3 6MT
Join Date: Sep 2013
Location: Staffs, UK

iTrader: (0)

Cool idea!
Appreciate 0
      01-28-2016, 09:42 AM   #3
Rotary Rasp
Lieutenant Colonel
Rotary Rasp's Avatar
241
Rep
1,857
Posts

Drives: 2009 E92 335i 6MT
Join Date: Aug 2008
Location: SoCal - Torrance

iTrader: (6)

Great idea!

But why is it so rusty in your engine bay? That might be the bigger issue.
__________________
Appreciate 0
      01-29-2016, 03:18 AM   #4
Figure807
Power without control is no power at all...
Figure807's Avatar
United_States
15
Rep
190
Posts

Drives: 335i 6spd Blk/Blk
Join Date: Oct 2009
Location: Honolulu, Hawaii

iTrader: (1)

Quote:
Originally Posted by Rotary Rasp View Post
Great idea!

But why is it so rusty in your engine bay? That might be the bigger issue.
I'm in Hawaii - ocean air does a number on everything.
__________________
2009 335i Coupe 6MT Blk Sapphire / Blk Leather
2007 328i Coupe 6MT Blk Sapphire / Blk Leather *Sold
1985 Toyota Corolla GTS 5MT 1.5-way Slvr / Blk *Sold
1987 Toyota Corolla GTS 5MT KAAZ 2-way Blk / Blk *Sold
Appreciate 0
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 09:01 PM.




e90post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST