my n55 procede before and after dyno

ian2002525 · 07-06-2011, 10:34 PM

Just had chance to run dyno last week at TopSpeed MotorSport in ATL.
Wanna to share some pictures and dyno graph.
first graph i had only eisenmann exhaust
second graph is after procede (map2) installed
and the torque line droped horribly...
only gain +10whp/50tq

and on the way home i tried 6th gear wot on highway, suddenly turned to limp mode...at the time the oil temp was only 240..wth!

N55 · 07-06-2011, 11:00 PM

THat's better than me with procede on Map1. I couldn't break 300. I have injen intake and procede. Sucks

EDIT: With OG DME software.

shockin330i · 07-06-2011, 11:23 PM

have you upgraded your dme?

N55 · 07-07-2011, 01:38 AM

Quote:

Originally Posted by shockin330i

have you upgraded your dme?

I tried with the dealer but I literally dropped it off 1 hour before your advice of disconnecting the CANbus wires. I go in for service on the 18th and will re dyno the same week

Have you dyno'd yet?

FrankiE90 · 07-07-2011, 01:42 AM

you should get in the mail'n list for the new procede beta maps.
email shiv -

reminds us of your mods
and type of gas u were using -

FrankiE90 · 07-19-2011, 01:24 AM

i'm look'n at ur numbers again - do u have a boost leak?

-u know i'm jok'n.
add ur video to this link.

ian2002525 · 07-19-2011, 01:56 AM

Quote:

Originally Posted by FrankiE90

i'm look'n at ur numbers again - do u have a boost leak?

teach me how to check boost leak?

FrankiE90 · 07-19-2011, 04:48 AM

Quote:

Originally Posted by ian2002525

teach me how to check boost leak?

i don't think that's the case with ur bimmer -
but here's the test

diy by sniz
good read.
http://www.e90post.com/forums/showthread.php?t=193077

Slops · 07-19-2011, 07:33 AM

yeah thats no good... but you gotta let us know all the conditions though. It looks like your on an AWD dyno so i gotta ask if you have xdrive? There are just procedures that Shiv talked about to make sure you dyno your xdrive correctly or it'll go into limp mode for sure.

Other factors are what the temp was outside?... Did you let the car auto-tune before you went on the dyno? What was your auto-tuned boost at the point of dyno-ing? Updating to the new firmware / beta maps would help if you haven't done so already? What other mods do you have?

07-06-2011, 10:34 PM	#1
ian2002525 台灣台北市 88 Rep 1,267 Posts Drives: 2009 GT-R Premium Join Date: Jun 2010 Location: Brentwood, TN/台灣 iTrader: (6) Garage List 2011 335i coupe [9.00]	Just had chance to run dyno last week at TopSpeed MotorSport in ATL. Wanna to share some pictures and dyno graph. first graph i had only eisenmann exhaust second graph is after procede (map2) installed and the torque line droped horribly... only gain +10whp/50tq and on the way home i tried 6th gear wot on highway, suddenly turned to limp mode...at the time the oil temp was only 240..wth! Attached Images Last edited by ian2002525; 07-06-2011 at 10:48 PM..
	Appreciate 0 Tweet Quote

07-06-2011, 11:00 PM	#2
N55 ⒸⒺⓇⓉⓘⒻⒾⒺⒹ✬ⓃⒾⓃⒿⒶ 137 Rep 1,475 Posts Drives: 🚀 Join Date: Nov 2010 Location: Pittsburgh iTrader: (3) Garage List 2015 BMW M4 [0.00] 2012 BMW 335IS (SOLD) [6.84] 2011 BMW 335XI (SOLD) [4.66] 2008 BMW 335xi (SOLD) [10.00]	THat's better than me with procede on Map1. I couldn't break 300. I have injen intake and procede. Sucks EDIT: With OG DME software. Last edited by N55; 07-07-2011 at 01:39 AM..
	Appreciate 0 Quote

07-06-2011, 11:23 PM	#3
shockin330i Brigadier General 798 Rep 4,784 Posts Drives: 2016 ZCP M3 Join Date: Jan 2007 Location: f y'all, I'm from Texas (RGV) iTrader: (1)	have you upgraded your dme? __________________ ERnie 2016 BSM/f80/ZCP
	Appreciate 0 Quote

07-07-2011, 01:42 AM	#5
FrankiE90 Major General 654 Rep 8,801 Posts Drives: Krooked Sk8board Join Date: Feb 2008 Location: Pasadena, Ca iTrader: (11)	you should get in the mail'n list for the new procede beta maps. email shiv - reminds us of your mods and type of gas u were using - __________________ FrankiE90 AKA:.[The TANK] *CLICK THE SIG E90s (been gone but not forgotten) • KW clubsports • • • • • • • • • • 18" BBS GT4 // Build E30 (pending) + E46 M3 Wagon ESTORIL Blue
	Appreciate 0 Quote

07-19-2011, 01:24 AM	#6
FrankiE90 Major General 654 Rep 8,801 Posts Drives: Krooked Sk8board Join Date: Feb 2008 Location: Pasadena, Ca iTrader: (11)	i'm look'n at ur numbers again - do u have a boost leak? -u know i'm jok'n. add ur video to this link. __________________ FrankiE90 AKA:.[The TANK] *CLICK THE SIG E90s (been gone but not forgotten) • KW clubsports • • • • • • • • • • 18" BBS GT4 // Build E30 (pending) + E46 M3 Wagon ESTORIL Blue
	Appreciate 0 Quote

07-19-2011, 07:33 AM	#9
Slops Major General 188 Rep 5,417 Posts Drives: 2005 C55 AMG Join Date: Jan 2011 Location: Oxford iTrader: (2)	yeah thats no good... but you gotta let us know all the conditions though. It looks like your on an AWD dyno so i gotta ask if you have xdrive? There are just procedures that Shiv talked about to make sure you dyno your xdrive correctly or it'll go into limp mode for sure. Other factors are what the temp was outside?... Did you let the car auto-tune before you went on the dyno? What was your auto-tuned boost at the point of dyno-ing? Updating to the new firmware / beta maps would help if you haven't done so already? What other mods do you have?
	Appreciate 0 Quote