Question for Shiv...

RetroGamerJP · 06-11-2007, 09:23 AM

Shiv,

is there a stock map that can be loeaded into the proceed if I am running 1.45?

I know you had shared stock maps a while ago buit I seemed to remeber reading that old maps would not work with the most recent version of the software.

I am taking tha car in for service on Wednesday and while I am not planning on removing the procede I also do not want them driving it with the extra HP.

Many Thanks,

AR230WAKEBOARDER · 06-11-2007, 09:57 AM

I have a upcoming service visit also. I was trying to decide if I should remove Procede or just install the bypass plugs(runs stock).

RetroGamerJP · 06-11-2007, 12:28 PM

I was hoping to not have to disassemble to get back to the actual PROcede for the bypass plug install. loading a new map would be the easiest for my goal. If they look close enough they are going to see my Boost Guage/ EGT & Widband sensors / Exhaust / Wheels & Suspension etc. and possible PROcede if they really dig. So it's pretty obvious the car has been modified to some extent. I'm not trying to pull anything over on the dealer, just don't want them going out for a joy ride and having something happen to the car.

RetroGamerJP · 06-12-2007, 08:46 AM

bump

e.n335 · 06-12-2007, 01:52 PM

If you load the v1.00 stock map with PROcede Reader v1.00 to the PROcede and you save it with PROcede Reader v1.01 from the PROcede you will have a v1.01 stock map.

OpenFlash · 06-12-2007, 02:14 PM

Quote:

Originally Posted by jp335i

I was hoping to not have to disassemble to get back to the actual PROcede for the bypass plug install. loading a new map would be the easiest for my goal. If they look close enough they are going to see my Boost Guage/ EGT & Widband sensors / Exhaust / Wheels & Suspension etc. and possible PROcede if they really dig. So it's pretty obvious the car has been modified to some extent. I'm not trying to pull anything over on the dealer, just don't want them going out for a joy ride and having something happen to the car.

You can plug in the bypass plugs without having to remove the whole bulkhead cover. Just pop off the black ECU lid, unfasten 2 of the 4 clips on the biege ECU lid, lift the loose side up a couple of inches and you should be able to get your fingers in there to uplug the harness and plug in the bypass plugs. Total job should only take 30 sec and not require any tools. If you still want a stock map, lemme know and I can email one to you.

Shiv

gonzo · 06-12-2007, 02:32 PM

30 seconds....ok, you need this as an avatar.

bnj · 06-12-2007, 02:45 PM

Shiv, now that you are on an optimistic mood, any plans for upgraded turbine housings?

RetroGamerJP · 06-12-2007, 07:10 PM

Quote:

Originally Posted by shiv@vishnu

You can plug in the bypass plugs without having to remove the whole bulkhead cover. Just pop off the black ECU lid, unfasten 2 of the 4 clips on the biege ECU lid, lift the loose side up a couple of inches and you should be able to get your fingers in there to uplug the harness and plug in the bypass plugs. Total job should only take 30 sec and not require any tools. If you still want a stock map, lemme know and I can email one to you.

Shiv

Thanks Shiv... I just sent you a PM

06-11-2007, 09:23 AM	#1
RetroGamerJP First Lieutenant 48 Rep 390 Posts Drives: 2019 M4 Join Date: Sep 2006 Location: Atlanta GA iTrader: (3)	Shiv, Need your help PLEASE Shiv, is there a stock map that can be loeaded into the proceed if I am running 1.45? I know you had shared stock maps a while ago buit I seemed to remeber reading that old maps would not work with the most recent version of the software. I am taking tha car in for service on Wednesday and while I am not planning on removing the procede I also do not want them driving it with the extra HP. Many Thanks, Last edited by RetroGamerJP; 06-12-2007 at 08:45 AM..
	Appreciate 0 Tweet Quote

06-11-2007, 09:57 AM	#2
AR230WAKEBOARDER Private First Class 4 Rep 144 Posts Drives: MONTEGO BLUE 335I Join Date: Mar 2007 Location: Why? iTrader: (0)	I have a upcoming service visit also. I was trying to decide if I should remove Procede or just install the bypass plugs(runs stock).
	Appreciate 0 Quote

06-11-2007, 12:28 PM	#3
RetroGamerJP First Lieutenant 48 Rep 390 Posts Drives: 2019 M4 Join Date: Sep 2006 Location: Atlanta GA iTrader: (3)	I was hoping to not have to disassemble to get back to the actual PROcede for the bypass plug install. loading a new map would be the easiest for my goal. If they look close enough they are going to see my Boost Guage/ EGT & Widband sensors / Exhaust / Wheels & Suspension etc. and possible PROcede if they really dig. So it's pretty obvious the car has been modified to some extent. I'm not trying to pull anything over on the dealer, just don't want them going out for a joy ride and having something happen to the car.
	Appreciate 0 Quote

06-12-2007, 08:46 AM	#4
RetroGamerJP First Lieutenant 48 Rep 390 Posts Drives: 2019 M4 Join Date: Sep 2006 Location: Atlanta GA iTrader: (3)	bump
	Appreciate 0 Quote

06-12-2007, 01:52 PM	#5
e.n335 Moderator 270 Rep 4,481 Posts Drives: e93 ///M3 DCT, 07/2009 Join Date: Feb 2007 Location: Switzerland, ZH iTrader: (0)	If you load the v1.00 stock map with PROcede Reader v1.00 to the PROcede and you save it with PROcede Reader v1.01 from the PROcede you will have a v1.01 stock map.
	Appreciate 0 Quote

06-12-2007, 02:32 PM	#7
gonzo Lieutenant General 10198 Rep 14,397 Posts Drives: as many as possible Join Date: Jan 2007 Location: TeXXXas iTrader: (0)	30 seconds....ok, you need this as an avatar. __________________ Crazy Diamond Last edited by gonzo; 08-07-2007 at 11:51 AM..
	Appreciate 0 Quote

06-12-2007, 02:45 PM	#8
bnj Banned 14 Rep 1,137 Posts Drives: e92 335i Join Date: Nov 2006 Location: Helsinki iTrader: (0)	Shiv, now that you are on an optimistic mood, any plans for upgraded turbine housings?
	Appreciate 0 Quote