Help Needed: Front K member/Engine cradle/axle support info

Ingeniator · 03-14-2014, 10:30 AM

Hey Guy's

So I'm rebuilding my 135I. It looks like I need to replace the front K member. Part # 31116785639 is common to all E8xE9x cars. I've found one on ebay for a good price but I want to confirm it has no deformation prior to purchasing. Can anyone tell me what the proper distance is between body mount bolt holes, wishbone mounts and tension strut mounts. and what the cross measure distance should be corner to corner.

Any help is greatly appreciated.

Ingeniator · 03-14-2014, 07:32 PM

Nobody has a car on a lift/stands that can measure this for me?

Ingeniator · 03-15-2014, 10:42 AM

Bump for help. There has to be someone on stands that owns a tape measure. Saving me 400 bucks would be great.

cnuyen · 11-06-2017, 11:39 PM

WHAT exactly do you need? I have a 2009 135i with sport package I bought with 14,300 mi. its still brand new as far as I am concerned. although its got 22,6xx on her now.

If you can send me a photo of what you whnt measured I can through her on stands and get it done for ya!

Might be a couple days, it at body shop have a ER FE WB kit reinstalled to correct the hack misalignment job my shop screwed me up on the first time around. Now the Siebon GTR hood is going on too.

Then TCKline Dual adjust rear Koni's, swift springs and thrust bearings and helpers, along with the front set up from TCKline that is part of the whole Kit, Vorshlag plates.

Should handle like a animal with 18X9.5 Square and 275/ 35/ 18 Michelin SSI bought it for $24k AND PUT IN ANOTHER $25k SO FAR NOT INCLUDING THE NEW THINGS I JUST MENTIONED.

cjn

cnuyen · 11-06-2017, 11:41 PM

LOOL my bad I should have looked at he date of the post.

I am not used to using these blogs and forums yet.

cjn

I get dumb ass of the day award!

03-14-2014, 10:30 AM	#1
Ingeniator Major 34 Rep 1,093 Posts Drives: 07 335XI(90) 09 135I(82) Join Date: Nov 2013 Location: Fort Mac, Alberta iTrader: (1)	Help Needed: Front K member/Engine cradle/axle support info Hey Guy's So I'm rebuilding my 135I. It looks like I need to replace the front K member. Part # 31116785639 is common to all E8xE9x cars. I've found one on ebay for a good price but I want to confirm it has no deformation prior to purchasing. Can anyone tell me what the proper distance is between body mount bolt holes, wishbone mounts and tension strut mounts. and what the cross measure distance should be corner to corner. Any help is greatly appreciated. __________________ 07 335XI (A008006) 6AT ~94K miles JB4 G5 ISO VSRF DP's 09 135I M (VK80379) 6MT. Race Project car. 1) Install Cobb/piggyback? and Motiv 600 Kit[HTA3076R w/ tial .82] 2) JRZ or Moton suspension. 3) Build high flow intake manifold with multi-port fuel and relocate OFH 4) Build full cage 5) Complete staged twin setup with HTA4205R [w/Tial 1.16] 6) Complete dry sump system Last edited by Ingeniator; 03-15-2014 at 10:40 AM..
	Appreciate 0 Tweet Quote

03-14-2014, 07:32 PM	#2
Ingeniator Major 34 Rep 1,093 Posts Drives: 07 335XI(90) 09 135I(82) Join Date: Nov 2013 Location: Fort Mac, Alberta iTrader: (1)	Nobody has a car on a lift/stands that can measure this for me? __________________ 07 335XI (A008006) 6AT ~94K miles JB4 G5 ISO VSRF DP's 09 135I M (VK80379) 6MT. Race Project car. 1) Install Cobb/piggyback? and Motiv 600 Kit[HTA3076R w/ tial .82] 2) JRZ or Moton suspension. 3) Build high flow intake manifold with multi-port fuel and relocate OFH 4) Build full cage 5) Complete staged twin setup with HTA4205R [w/Tial 1.16] 6) Complete dry sump system
	Appreciate 0 Quote

03-15-2014, 10:42 AM	#3
Ingeniator Major 34 Rep 1,093 Posts Drives: 07 335XI(90) 09 135I(82) Join Date: Nov 2013 Location: Fort Mac, Alberta iTrader: (1)	Bump for help. There has to be someone on stands that owns a tape measure. Saving me 400 bucks would be great. __________________ 07 335XI (A008006) 6AT ~94K miles JB4 G5 ISO VSRF DP's 09 135I M (VK80379) 6MT. Race Project car. 1) Install Cobb/piggyback? and Motiv 600 Kit[HTA3076R w/ tial .82] 2) JRZ or Moton suspension. 3) Build high flow intake manifold with multi-port fuel and relocate OFH 4) Build full cage 5) Complete staged twin setup with HTA4205R [w/Tial 1.16] 6) Complete dry sump system
	Appreciate 0 Quote

11-06-2017, 11:39 PM	#4
cnuyen New Member 5 Rep 5 Posts Drives: 2009 135i built 09/08 Join Date: Mar 2016 Location: Geneva, IL. iTrader: (0) Garage List 2009 BMW 135i [0.00] 2010 BMW M6 SMG [0.00] 2009 BMW 135i [0.00]	WHAT exactly do you need? I have a 2009 135i with sport package I bought with 14,300 mi. its still brand new as far as I am concerned. although its got 22,6xx on her now. If you can send me a photo of what you whnt measured I can through her on stands and get it done for ya! Might be a couple days, it at body shop have a ER FE WB kit reinstalled to correct the hack misalignment job my shop screwed me up on the first time around. Now the Siebon GTR hood is going on too. Then TCKline Dual adjust rear Koni's, swift springs and thrust bearings and helpers, along with the front set up from TCKline that is part of the whole Kit, Vorshlag plates. Should handle like a animal with 18X9.5 Square and 275/ 35/ 18 Michelin SSI bought it for $24k AND PUT IN ANOTHER $25k SO FAR NOT INCLUDING THE NEW THINGS I JUST MENTIONED. cjn
	Appreciate 0 Quote

11-06-2017, 11:41 PM	#5
cnuyen New Member 5 Rep 5 Posts Drives: 2009 135i built 09/08 Join Date: Mar 2016 Location: Geneva, IL. iTrader: (0) Garage List 2009 BMW 135i [0.00] 2010 BMW M6 SMG [0.00] 2009 BMW 135i [0.00]	LOOL my bad I should have looked at he date of the post. I am not used to using these blogs and forums yet. cjn I get dumb ass of the day award!
	Appreciate 0 Quote