Three Stage Intake Manifold Conversion for 328/325

DickBlisken · 02-27-2014, 02:20 PM

Quote:

Originally Posted by e90pilot

If the manifold comes with the actuator motors attached you won't need any of that. But you will need a gasket set.

Ah, got ya. The manifold isn't coming with the actuator motors attached. From the photos I was sent, it doesn't look like the hardware is included.

e90pilot · 02-27-2014, 02:39 PM

Quote:

Originally Posted by Nico87

Ah, got ya. The manifold isn't coming with the actuator motors attached. From the photos I was sent, it doesn't look like the hardware is included.

Ok then you'll need the screws. You'll need these for sure
11617535849 x5 Screw 50x20
11617535850 x2 Screw 50x35
11617535851 x1 Screw 50x66

You should be able to reuse your old manifold screws as long as they're not aluminum or damaged.

DickBlisken · 02-27-2014, 02:40 PM

Quote:

Originally Posted by e90pilot

Ok then you'll need the screws. You'll need these for sure
11617535849 x5 Screw 50x20
11617535850 x2 Screw 50x35
11617535851 x1 Screw 50x66

You should be able to reuse your old manifold screws as long as they're not aluminum or damaged.

Perfect. Thanks so much, appreciate it!

dragosdor · 04-07-2014, 09:34 AM

hello there everyone, Im looking to do this mod myself, I drive an 09 LCI 328i with N51 engine and by reading tons of pages on this forum I have learned that my engine might already come with a 3 stage manifold installed! I verified with realoem website and by selecting 2009/328i/manufactured 06/09 it will indeed show its a 3 stage manifold with 2 disa valves. I could not believe this so I went outside to check the car myself, it does indeed have 2 disa valves on the intake!! Does it mean I have that 3 stage or not?
I cannot find a part number label on the car, but I'm asking everyone here: does 2 disa valves mean its a 3stage for sure?

Thank you!

e90pilot · 04-07-2014, 10:01 AM

Yes you already have the 3 stage intake manifold. All N51s are equipped with a 3 stage. Due to the lower compression compared with the N52, BMW used a the 3 stage intake manifold to make up loss in power.

DUI Elite · 04-07-2014, 10:43 AM

Sorry to ask so late in the thread, but any recommendations on sites for buying the intake manifold?

I will likely consider getting the DISA Adjusters new..

06 325i here. I have an EC Stage 1 tune. But have been itching to get the ball rolling with this to get the Stage 2 tune.

Taskmaster · 04-07-2014, 11:05 AM

Quote:

Originally Posted by DUI Elite

Sorry to ask so late in the thread, but any recommendations on sites for buying the intake manifold?

I will likely consider getting the DISA Adjusters new..

06 325i here. I have an EC Stage 1 tune. But have been itching to get the ball rolling with this to get the Stage 2 tune.

car-part.com You can search for a N51 engine or from a Z4 Si engine

andrey_gta · 04-07-2014, 08:46 PM

when sources dry up look here:
ebay.co.uk and http://en.bildelsbasen.se/

DUI Elite · 04-08-2014, 10:50 PM

thanks guys

Rodny · 05-12-2014, 05:26 PM

just called Bavarian and they want $550 with the disa valves, ask the guy why they charging so much and he said to many people asking for the part.

I guess is better then $950.
any other place i can look for it?

jc_bmw · 05-12-2014, 05:26 PM

Look for a used one from auto wreckers.... around $300 with DISA

alex_beridze · 09-30-2014, 01:32 AM

Quote:

Originally Posted by jc_bmw

Look for a used one from auto wreckers.... around $300 with DISA

hello my friends, I am planning to change 328 intake with 330 intake, but is I see the pictures of the old intake(fount in internet)there are not disa valve on the top. and stage 3 intake hes disa valve, questen is: where connect new disa valve, how find cable from ecu? How find cable for new disa?
Please help me...

Taskmaster · 09-30-2014, 09:40 AM

They were on the side of the old manifold held in place - shorter cord in the front, longer one in the rear.

jc_bmw · 09-30-2014, 10:33 AM

Quote:

Originally Posted by alex_beridze

hello my friends, I am planning to change 328 intake with 330 intake, but is I see the pictures of the old intake(fount in internet)there are not disa valve on the top. and stage 3 intake hes disa valve, questen is: where connect new disa valve, how find cable from ecu? How find cable for new disa?
Please help me...

From this picture that you posted

The cables for the DISA valve should be located on the left where your red circle ends you see those two little nibs that sticks out? There should be two wire harness connected to those nibs. You pull them off the manifold and you use the short for the front and long for the rear (closer to engine)

alex_beridze · 09-30-2014, 12:35 PM

Quote:

Originally Posted by jc_bmw

From this picture that you posted

The cables for the DISA valve should be located on the left where your red circle ends you see those two little nibs that sticks out? There should be two wire harness connected to those nibs. You pull them off the manifold and you use the short for the front and long for the rear (closer to engine)

This is Disa valve connectors? long is outside valve connector? and end short inside valve conector?

jc_bmw · 09-30-2014, 12:49 PM

the one on the right looks like it you still need to remove the plastic cover. Not sure about the left

andrey_gta · 09-30-2014, 02:12 PM

Quote:

Originally Posted by alex_beridze

This is Disa valve connectors? long is outside valve connector? and end short inside valve conector?

those dont look like disa connectors - they come from blow the manifold to a metal Box

the cables in the picture are to manifold sensors i think

328XIdiot · 09-30-2014, 02:25 PM

The DISA cables should have been connected to the old manifold. You should have had to remove them from the old manifold when you removed it. And as previously stated, they go to a junction box that connects to the bottom of the manifold.

alex_beridze · 09-30-2014, 03:01 PM

Quote:

Originally Posted by 328XIdiot

The DISA cables should have been connected to the old manifold. You should have had to remove them from the old manifold when you removed it. And as previously stated, they go to a junction box that connects to the bottom of the manifold.

Can anyone shows me where they connected bottom of the manifold? I must change connectors or 328 disa connectors are same?

alex_beridze · 09-30-2014, 03:13 PM

Quote:

Originally Posted by alex_beridze

Can anyone shows me where they connected bottom of the manifold? I must change connectors or 328 disa connectors are same?

Maybe this is disa valve conectors?

jc_bmw · 09-30-2014, 03:27 PM

Quote:

Originally Posted by alex_beridze

Maybe this is disa valve conectors?

Nope that is not it.

Rodny · 09-30-2014, 05:51 PM

Quote:

Originally Posted by 328XIdiot

The DISA cables should have been connected to the old manifold. You should have had to remove them from the old manifold when you removed it. And as previously stated, they go to a junction box that connects to the bottom of the manifold.

You can see on the picture in yellow.

sorry misspell connector....

Name: 3stage.jpg
Views: 3559
Size: 214.3 KB

04-07-2014, 09:34 AM	#510
dragosdor IR CSEL CMEL CFI 3 Rep 202 Posts Drives: F30d LCI Join Date: Mar 2014 Location: Houston TX iTrader: (1)	hello there everyone, Im looking to do this mod myself, I drive an 09 LCI 328i with N51 engine and by reading tons of pages on this forum I have learned that my engine might already come with a 3 stage manifold installed! I verified with realoem website and by selecting 2009/328i/manufactured 06/09 it will indeed show its a 3 stage manifold with 2 disa valves. I could not believe this so I went outside to check the car myself, it does indeed have 2 disa valves on the intake!! Does it mean I have that 3 stage or not? I cannot find a part number label on the car, but I'm asking everyone here: does 2 disa valves mean its a 3stage for sure? Thank you!
	Appreciate 0 Quote

04-07-2014, 10:01 AM	#511
e90pilot Freight Dawg 104 Rep 2,103 Posts Drives: E90 325i Join Date: Jul 2005 Location: Oakland, CA iTrader: (3)	Yes you already have the 3 stage intake manifold. All N51s are equipped with a 3 stage. Due to the lower compression compared with the N52, BMW used a the 3 stage intake manifold to make up loss in power. __________________ --Marcelo '06 Arctic Metallic 325i \| Sport Package \| 6MT \| Dinan Stage III suspension \| Dinan exhaust \| 330i manifold swap! Click here! \| Active Autowerke tune \| 135i Brake Calipers \| Deiselboost caliper brackets \| E46 M3 front rotors
	Appreciate 0 Quote

04-07-2014, 10:43 AM	#512
DUI Elite ///M at Heart 90 Rep 1,954 Posts Drives: 06 SGM E90, 15 BSM E84 Join Date: Jan 2011 Location: Chicago, IL iTrader: (4)	Sorry to ask so late in the thread, but any recommendations on sites for buying the intake manifold? I will likely consider getting the DISA Adjusters new.. 06 325i here. I have an EC Stage 1 tune. But have been itching to get the ball rolling with this to get the Stage 2 tune. __________________ \| 3-IM \| AA Headers \| Eurocharged Stage-3 \| BMW PI \|
	Appreciate 0 Quote

04-07-2014, 08:46 PM	#514
andrey_gta Brigadier General 298 Rep 4,040 Posts Drives: 130i coupé ;) Join Date: Nov 2011 Location: Bimmerpost iTrader: (1) Garage List 2008 BMW 128i [10.00]	when sources dry up look here: ebay.co.uk and http://en.bildelsbasen.se/ __________________ 128i Sport 6MT converted to Euro 130i spec, 3.73 diff, tuned by evolve ~220 whp 207 wtq(ft-lb) SAE In-progress: //M front arm, M3 rack, e36M lip Wishlist: Coils, n55 mnts, headers, LSD, e60 finn diff "The 1-series is the last car that BMW engineered before the Germans, as a car-making culture, fell out of love with driving." - R&T 2013 135is
	Appreciate 0 Quote

04-08-2014, 10:50 PM	#515
DUI Elite ///M at Heart 90 Rep 1,954 Posts Drives: 06 SGM E90, 15 BSM E84 Join Date: Jan 2011 Location: Chicago, IL iTrader: (4)	thanks guys __________________ \| 3-IM \| AA Headers \| Eurocharged Stage-3 \| BMW PI \|
	Appreciate 0 Quote

05-12-2014, 05:26 PM	#516
Rodny First Lieutenant 39 Rep 344 Posts Drives: 08 328i Join Date: Mar 2014 Location: United States iTrader: (0)	just called Bavarian and they want $550 with the disa valves, ask the guy why they charging so much and he said to many people asking for the part. I guess is better then $950. any other place i can look for it?
	Appreciate 0 Quote

05-12-2014, 05:26 PM	#517
jc_bmw First Lieutenant 59 Rep 383 Posts Drives: 2009 BMW 328i E90 Join Date: Jun 2013 Location: Markham, Ontario iTrader: (3)	Look for a used one from auto wreckers.... around $300 with DISA __________________ 09 E90 328i 3IM, Eurocharged, K&N, 80W LED Angel Coding: Digi Speed, Express Up Fob, Wipe Wash Count, Weather Station, Headlight Sensitivity
	Appreciate 0 Quote

09-30-2014, 09:40 AM	#519
Taskmaster Banned 2465 Rep 9,004 Posts Drives: M235i 6MT / E92 328 Msport 6MT Join Date: Nov 2013 Location: Florida iTrader: (6)	They were on the side of the old manifold held in place - shorter cord in the front, longer one in the rear.
	Appreciate 0 Quote

09-30-2014, 12:49 PM	#522
jc_bmw First Lieutenant 59 Rep 383 Posts Drives: 2009 BMW 328i E90 Join Date: Jun 2013 Location: Markham, Ontario iTrader: (3)	the one on the right looks like it you still need to remove the plastic cover. Not sure about the left __________________ 09 E90 328i 3IM, Eurocharged, K&N, 80W LED Angel Coding: Digi Speed, Express Up Fob, Wipe Wash Count, Weather Station, Headlight Sensitivity
	Appreciate 0 Quote

09-30-2014, 02:25 PM	#524
328XIdiot Private First Class 28 Rep 121 Posts Drives: E92 328xi 6MT Join Date: Aug 2014 Location: Northwest Chicago Suburbs iTrader: (0)	The DISA cables should have been connected to the old manifold. You should have had to remove them from the old manifold when you removed it. And as previously stated, they go to a junction box that connects to the bottom of the manifold.
	Appreciate 0 Quote