|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
Just failed inspection : Not Ready
|
|
02-21-2012, 01:37 PM | #1 |
D:
56
Rep 435
Posts
Drives: 2 paur 2 aford kar :(
Join Date: Sep 2009
Location: Section 8 hauzing in qnz, ny
|
Just failed inspection : Not Ready
Well, as the title says, I just brought my car in for an inspection with only the JB4 and DCI's installed. I originally left the tune in map 2, however after they tried scanning it the first time I put it in map 0 and asked them to try again. The OBDII scanner said "Not Ready" again. Also, I haven't cleared any codes in months. Any advice?
__________________
Contact me for all your Architectural and Engineering needs in the greater NYC area
MBA Engineering PC |
02-21-2012, 01:40 PM | #3 |
D:
56
Rep 435
Posts
Drives: 2 paur 2 aford kar :(
Join Date: Sep 2009
Location: Section 8 hauzing in qnz, ny
|
lol... is that really all? I feel like a fool
__________________
Contact me for all your Architectural and Engineering needs in the greater NYC area
MBA Engineering PC |
Appreciate
0
|
02-21-2012, 01:50 PM | #4 |
Major General
188
Rep 5,417
Posts |
yeah it may take quicker depending on your car to set the readiness i guess... but mine was fine when i put it on map0 and turned canclear off for about 100miles before i knew it was going into service.
|
Appreciate
0
|
02-21-2012, 01:58 PM | #5 |
D:
56
Rep 435
Posts
Drives: 2 paur 2 aford kar :(
Join Date: Sep 2009
Location: Section 8 hauzing in qnz, ny
|
I'm assuming you have a procede. So for a JB4 all I'd need to do is turn off the tune?
__________________
Contact me for all your Architectural and Engineering needs in the greater NYC area
MBA Engineering PC |
Appreciate
0
|
02-21-2012, 02:17 PM | #7 |
Captain
37
Rep 735
Posts
Drives: 2013 F30 335i X-Drive MSport
Join Date: Sep 2010
Location: Brooklyn
|
Had a similar issue recently. I had some work done on my car and some codes cleared. The best bet is to drive for about 50 miles at a constant speed without pressing on the brakes too much (a highway with no traffic) and combine with a little city driving for about 20 miles or so. Did the trick for me.
__________________
2013 F30 335i X-Drive / AW / CR / MSPORT / PREMIUM / TECH / HK / Heated Seats / Sport Auto / PDC / M Performance Grills and Spoiler / 20% tint (sold)
1995 Toyota Supra Single Turbo (for sale) |
Appreciate
0
|
02-21-2012, 03:07 PM | #8 |
D:
56
Rep 435
Posts
Drives: 2 paur 2 aford kar :(
Join Date: Sep 2009
Location: Section 8 hauzing in qnz, ny
|
Cool thanks guys
__________________
Contact me for all your Architectural and Engineering needs in the greater NYC area
MBA Engineering PC |
Appreciate
0
|
02-22-2012, 10:22 PM | #10 |
Captain
19
Rep 712
Posts |
This help me. http://www.e90post.com/forums/showthread.php?t=365042
|
Appreciate
0
|
02-22-2012, 11:54 PM | #11 |
Captain
54
Rep 627
Posts |
so if i have a N55 how can i pass with a downpipe installed. I have the service engine soon light on without having auto clear on. but then i wont pass if i have autoclear on
|
Appreciate
0
|
02-23-2012, 09:27 AM | #12 |
Second Lieutenant
13
Rep 221
Posts |
|
Appreciate
0
|
02-23-2012, 11:36 AM | #13 |
The Blue Beast
142
Rep 5,665
Posts |
Set it to map 0, clear codes. Drive around for a day or 2. Then go get the inspection without a sniffer if possible.
__________________
Cobb AP Stage 2+ | BMS DCI | UR Catless DP | UR Chargepipe | Tial BV 50mm | BSH OCC | ETS FMIC | Eisenmann Race Exhaust | KWv1 Coilovers | Volk TE37 TC Kline Ed. |
Appreciate
0
|
02-23-2012, 12:16 PM | #14 |
Major General
177
Rep 6,631
Posts |
Turn code clearing off, put in valet mode for 50-60 miles get inspected again. If you fail again you may have a legitimate hardware problem.
__________________
E90 LCI N54 6AT
|
Appreciate
0
|
02-23-2012, 12:59 PM | #15 |
D:
56
Rep 435
Posts
Drives: 2 paur 2 aford kar :(
Join Date: Sep 2009
Location: Section 8 hauzing in qnz, ny
|
thanks for the help everyone. I put it into map 0 and put about 50 miles on the car. just brought it back to the shop and they're finishing the inspection up now
__________________
Contact me for all your Architectural and Engineering needs in the greater NYC area
MBA Engineering PC |
Appreciate
0
|
02-29-2012, 04:31 PM | #16 |
Guest
0
Rep n/a
Posts
Drives:
|
Hey there, I am having the same problem. When I went thru emissions it came back "not ready". I was told to turn CAN "off" on the procede was the only fix. Sounds like driving around on "0" for a few days will do the trick. Just double checking, please confirm.
|
Appreciate
0
|
02-29-2012, 05:52 PM | #17 |
D:
56
Rep 435
Posts
Drives: 2 paur 2 aford kar :(
Join Date: Sep 2009
Location: Section 8 hauzing in qnz, ny
|
Worked for me. I drove around for 50 miles but if you don't have time to do that follow the instructions posted in this thread.
__________________
Contact me for all your Architectural and Engineering needs in the greater NYC area
MBA Engineering PC |
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|