|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
DIY Powered seat retrofit (WIP)
|
|
02-14-2014, 03:47 PM | #222 |
New Member
0
Rep 21
Posts |
Hello i have the same problem najt with the passeger seat (pin 4 7 and 9)and how or you wired the 3 pin in a fuse box? I block on the passenger because the 7 is lumbar , the 9 is heater module and the 4 ? I don't know
|
Appreciate
0
|
02-15-2014, 11:10 AM | #223 |
New Member
0
Rep 21
Posts |
hello i have the seat passager with heated module but i have the pin 4 in x279 I don't know where it goes , is cable 2.5mm color red , i thinks he go to siege adjustement because i have controled with metrics the pin 7 for lumbar, sport and the 9 for heated module .... i don't should nothing in WDS, my car is 2006 with standard (nothing electric) and the news seat 2011
anyone can help me for cable this pin x279 pin 1 ------ 38 x14270 pwm signal *******pin 4 ? *******pin 5 ------ 9 x11003 5A F29 terminal 15 *******pin 6 not used *******pin 7 -------1 x11006 30A F33 lombar and sport *******pin 8 ------- ground *******pin 9 -------- 6 x11004 30A F49 heated module ****** PIN10 ------- seat occupancy ****** PIN11 --------occupation *******PIN12 --------occupation *******Pin13---------ground sorry for my english |
Appreciate
0
|
02-15-2014, 05:12 PM | #224 |
Second Lieutenant
5
Rep 260
Posts |
sorry. which pin you dont have in cable from car? best would be add some pictures. full seat scheme with description is on 3rd. page.
http://www.e90post.com/forums/showth...=480313&page=3 as you can see. pin 4 is big one...for heating. I also think its for adjusting electric seats (front, back, up,down...etc). coz another + cable is on pin 7 or 9, which is for side bolster and lumbar, as you alread wrote. Last edited by Najt; 02-15-2014 at 05:19 PM.. |
Appreciate
0
|
02-16-2014, 05:34 AM | #225 |
New Member
0
Rep 21
Posts |
thanks for you response ,i don't have cable in this pin in the car because my original is not electric... i post photo the news seat and i what controlled ....
i thinks this pin 4 is adjustable seat electric but i don't know when i plug in fusebox.... the pin 9 and 4 are exchanged when i see the shema in page 3 because normally pin 4 is for heating or seat module but if you see in wds for car 2011 the pin 9 is for heating module and pin 4 only for seat module.... i am confused only with this pin 4 my drive seat have seat module but it's ok |
Appreciate
0
|
02-16-2014, 11:43 AM | #226 |
Major General
886
Rep 9,097
Posts |
Pin 4 is for power. Connect it to pin 7 or pin 9 and you will be good to go.
__________________
F36 Xdrive for her - HUD, park assist, heated steering wheel, rear camera, Apple car play
F36 RWD for him - HK, M sports pack, GTS tail light, Apple car play |
Appreciate
0
|
02-24-2014, 04:44 PM | #228 |
New Member
0
Rep 21
Posts |
hello i have installed the news seat but i have a problem , in a driver the lombar and bolster not work and passager is the heating not work
in drive i have connected the can with can controler. i don't know if the memory work , when i press the button is red.... my connection in driver is : pin 2 can pin 3 can pin 4 x11005 pin 7 x11005 pin 8 ground pin 13 ground |
Appreciate
0
|
02-25-2014, 05:35 AM | #229 |
New Member
0
Rep 21
Posts |
i have the news ! the driver seat is work in totality (adjustement, lumbar, heating) is was pin 13 ground not in the right place...
for my passager i have added $494 and coded ihk and jbbf , the buttom work but the seat not heating anyone have an idea ? |
Appreciate
0
|
04-17-2014, 04:19 PM | #232 |
Private First Class
5
Rep 128
Posts |
Thank you so much to the OP for this write up. I was able to get my seats in, and the can bus wires were the hang up I was having. They work great, and my 323 is moving on up. Cheers
|
Appreciate
0
|
04-25-2014, 01:09 AM | #233 |
New Member
2
Rep 10
Posts |
Confused
Hello all BMW lovers!
I have installed fully electric memory seats in my BMW E91 from 06 instead of the seats I had in fabric with heat. I have read everything on this page several times and installed the driver's seat with great success. Everything works on the driver's side memory, power, heat, etc., but not on the passenger side. There it is completely dead, I have 12V so I think it should work, the sideboolesters works fine and K_can I have not plugged in when I have understood that it only applies to the driver side and there are no pins on the passenger seat for K_can. So then my question! What am I missing? have been trying for two days now to get the passenger seat to work but it is really not so now I turn to you. please help! |
Appreciate
0
|
04-25-2014, 05:23 AM | #235 |
Major General
324
Rep 5,370
Posts |
I have kcan wiring on both seats. Maybe you should try that? Before when I only did power and ground without the kcan, the seats would lose power after a few minutes
|
Appreciate
0
|
04-25-2014, 05:32 AM | #236 | |
New Member
2
Rep 10
Posts |
Quote:
My seat don't work at all, just the sideboolesters. im going crazy. |
|
Appreciate
0
|
04-26-2014, 04:53 PM | #239 |
New Member
2
Rep 10
Posts |
Doesn't anybody know? I have read this thread many times but i cant get the passenger side to work, exept from the side bolster. I have conect pin 8 to 13 and pin 4, 7 and 9 to eachother and i got 12v to the seat. But still wont work...
And the seat dont have k-can beacuse its on passenger side. What am i missing? |
Appreciate
0
|
04-27-2014, 06:41 PM | #240 |
Major General
324
Rep 5,370
Posts |
The part where you labeled ???? Should be either power or ground cables. On my passenger side the side bolsters and actual movement are separate power and ground wires. Essentially you should have two power and two ground wires going into the seat. The way I wired mine was just to have one power and ground, then added a splitter to each one to create a total of 4 wires
|
Appreciate
0
|
04-28-2014, 12:19 AM | #241 |
New Member
2
Rep 10
Posts |
Yes, I've paired the power with each other and the same with the ground. I can not do that then?
I think it should work, I have power to the little black box, etc. but I can not get the seat to move .. But you think that I should have different power supplies to the various cables? thankfull for all helt i can get! |
Appreciate
0
|
04-28-2014, 07:23 AM | #242 |
Major General
324
Rep 5,370
Posts |
No the same power supply should work...I'm not really sure then. Even without kcan if you just wire power and ground to the seat you should have movement already. Maybe double check the connections again to make sure you've got the pins going to the right slot? Did you modify the seat wiring or your cars harness?
|
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|