V2 install issue

HyperM3 · 11-24-2007, 03:36 PM

Im installing my v2 on someones car and for some reason, I cant get the computer to read the PROcede. Got the USB cable hooked up and working properly. Changed the comms to 4 on both. But when I try to click "Go offline/online" it does nothing. It just says "copy to clipboard".

Anyone else get this issue?

pikkashoe · 11-24-2007, 03:47 PM

Did you push the key in and press the start button once?

worse case, you can turn the car on and see if it connects. i did this, and i uploaded the firmware and the car turned off, but as long as your computer doesnt turn off your fine.

scalbert · 11-24-2007, 03:48 PM

^^^^
Correct, be sure to pres the starter button twice.

HyperM3 · 11-24-2007, 03:48 PM

Yeah, had that figured out from reading the forum about previous issues.

We rebooted the laptop and reconfigured the comms but now we get this error "Cannot open com 4". We keep trying to use different com ports and each time is "cannot open com 6" or "cannot open com 7".

WTF!!! This is really frustrating. Just connecting the laptop is taking twice as long as the install itself.

scalbert · 11-24-2007, 03:49 PM

The port may have reset to another one. Verify under Device Manager which port it is using.

e90AW335i · 11-24-2007, 03:50 PM

Quote:

Originally Posted by scalbert

The port may have reset to another one. Verify under Device Manager which port it is using.

+1, I have this happen with other devices as well.....

HyperM3 · 11-24-2007, 03:51 PM

Quote:

Originally Posted by scalbert

The port may have reset to another one. Verify under Device Manager which port it is using.

We do and then reset it. After we decided to just let it think for itself, it still didnt want to open the one it set for itself.

scalbert · 11-24-2007, 03:53 PM

Quote:

Originally Posted by HyperM3

We do and then reset it. After we decided to just let it think for itself, it still didnt want to open the one it set for itself.

Uninstall the drivver and then reinstall the device.

Tuned335i · 11-24-2007, 03:56 PM

I had the same problem yesterday in my V2 install. I was using a serial cable however. Couldn't open the com Ports. I went back and looked at the V1.47 install instructions and it didn't say anything about messing with a com port setting. So I unplugged the cable from the laptop, shut down the PROcede software, plugged the cable back into the laptop, then ran the software again. I didn't go into the comms to change the port. I just clicked "go online/offline" in the comms menu and it worked.

This may not work for you if using a USB cable though.

M3to335 · 11-24-2007, 04:25 PM

I cant get my 6 foot cable to work, yet my 6 " cable works fine. Its really odd. On 1.47 It wasnt an issue. Im sure its all in my head, but its extremely ironic.

NPDAN · 11-24-2007, 04:26 PM

un plug the serial and plug it back in. See if it will recognize new hardware... too hard to trouble shoot without being there.

HyperM3 · 11-24-2007, 05:04 PM

Ok, so I pulled out my laptop and downloaded everything. Same thing started happening then all of a sudden we had "online" come up. We didnt even want to breathe on the car in case that set it off.

Downloaded all the maps and everything in that regard went smooth.

Now other issues. Started the car and BAM, it shut off after sputtering. Started it up again and it was good, then after a minute started sputtering again. Threw a LIMP CEL. I cleared the faults and started it up again. Did the same thing once again.

So I cleared the faults and put the plugs on and took the PROced box out. Started fine and ran fine no problems.

Now what?

NPDAN · 11-24-2007, 05:09 PM

Did it start and run fine with the bypass plugs plugged in?

E90ice · 11-24-2007, 05:11 PM

Wiring must be off. Check your wires.

HyperM3 · 11-24-2007, 05:11 PM

Quote:

Originally Posted by NPDAN

Did it start and run fine with the bypass plugs plugged in?

Yeah, worked fine with the bypass plugs.

I was just reading on the vishnuforums that it might be bricked. I unplugged the serial cable when it read "Download complete 100%". This was at the point where it says the ECU is restarting. However, there was no indication that the ECU had been restarted or was done.

bmwzimmer · 11-24-2007, 05:15 PM

do u have access to another laptop?

HyperM3 · 11-24-2007, 05:23 PM

Quote:

Originally Posted by E90ice

Wiring must be off. Check your wires.

Would the wiring be bad if the car works perfectly with the bypass plugs in?

Quote:

Originally Posted by bmwzimmer

do u have access to another laptop?

Yeah, the other laptop worked better but we are getting a new serial cable to see if that was a cluprit too.

e.n335 · 11-24-2007, 05:32 PM

Did you reset the car's ECU ?

Terry335 · 11-24-2007, 05:36 PM

Try to connect to box again with laptop. If its cooked it probably won't connect.

HyperM3 · 11-24-2007, 05:56 PM

Quote:

Originally Posted by e.n335

Did you reset the car's ECU ?

How do I do that?

Quote:

Originally Posted by Terry335

Try to connect to box again with laptop. If its cooked it probably won't connect.

Well, since we were having issues with the cable still not connecting well. We called it a night. He called me on the way home and said the car is driving perfectly with no error lights, just like stock.

I guess I dont have to check the wiring because it would obviously not work even with the bypass plugs in.

However, this is really frustrating. Mostly because its hurting my install credibility and its not my fault, its the stupid poor instructions and user program.

I litterally had the whole PROcede v1/v2 all hooked up in about 25 mins. Then we spent about 2.5 hours trying to get the software to work.

Terry335 · 11-24-2007, 05:57 PM

Quote:

Originally Posted by HyperM3

How do I do that?

Well, since we were having issues with the cable still not connecting well. We called it a night. He called me on the way home and said the car is driving perfectly with no error lights, just like stock.

I guess I dont have to check the wiring because it would obviously not work even with the bypass plugs in.

However, this is really frustrating. Mostly because its hurting my install credibility and its not my fault, its the stupid poor instructions and user program.

I litterally had the whole PROcede v1/v2 all hooked up in about 25 mins. Then we spent about 2.5 hours trying to get the software to work.

You swapped the map wire to the one with the resistor right?

HyperM3 · 11-24-2007, 06:00 PM

Quote:

Originally Posted by Terry335

You swapped the map wire to the one with the resistor right?

Um, I hope so. Dont know which one that was exactly. I really wished there was a good pictorial diagram of where things were supposed to be plugged in. I think more in an engineering type way with flowcharts and crap. Dont give me pics with wrong colored wires and say connect this to this.

11-24-2007, 03:36 PM	#1
HyperM3 Too many Alex's, from now on, call me Beaufort 342 Rep 6,188 Posts Drives: See Sig Join Date: Feb 2007 Location: Lawrenceville, NJ iTrader: (8)	V2 install issue - Help Im installing my v2 on someones car and for some reason, I cant get the computer to read the PROcede. Got the USB cable hooked up and working properly. Changed the comms to 4 on both. But when I try to click "Go offline/online" it does nothing. It just says "copy to clipboard". Anyone else get this issue? __________________ 13 HD FatBob 17 A4 Glacier/Black 1st Edition/Pre+/Sport/EurocodeTMD/Racechip 16 S6 (gone),14 S6 (gone),14 S6 (gone),13 S6 (gone),10 S4 (gone) 07 335i(gone)
	Appreciate 0 Tweet Quote

11-24-2007, 03:47 PM	#2
pikkashoe Major 56 Rep 1,239 Posts Drives: 2007 BMW 335 Coupe Join Date: Feb 2007 Location: Miami, FL iTrader: (1)	Did you push the key in and press the start button once? worse case, you can turn the car on and see if it connects. i did this, and i uploaded the firmware and the car turned off, but as long as your computer doesnt turn off your fine. __________________ 2007 E92 AW/Coral Red/Alumin, 6 speed manual, ZSP, PROCEDE V3.1, Factory Short-Throw Knob, Bms Filter. 12/7/07 - 12.84 @ 109.36
	Appreciate 0 Quote

11-24-2007, 03:48 PM	#3
scalbert Major General 153 Rep 5,780 Posts Drives: '13 S4, '15 Q7 Join Date: Feb 2007 Location: Woodstock, GA iTrader: (8)	^^^^ Correct, be sure to pres the starter button twice.
	Appreciate 0 Quote

11-24-2007, 03:48 PM	#4
HyperM3 Too many Alex's, from now on, call me Beaufort 342 Rep 6,188 Posts Drives: See Sig Join Date: Feb 2007 Location: Lawrenceville, NJ iTrader: (8)	Yeah, had that figured out from reading the forum about previous issues. We rebooted the laptop and reconfigured the comms but now we get this error "Cannot open com 4". We keep trying to use different com ports and each time is "cannot open com 6" or "cannot open com 7". WTF!!! This is really frustrating. Just connecting the laptop is taking twice as long as the install itself. __________________ 13 HD FatBob 17 A4 Glacier/Black 1st Edition/Pre+/Sport/EurocodeTMD/Racechip 16 S6 (gone),14 S6 (gone),14 S6 (gone),13 S6 (gone),10 S4 (gone) 07 335i(gone)
	Appreciate 0 Quote

11-24-2007, 03:49 PM	#5
scalbert Major General 153 Rep 5,780 Posts Drives: '13 S4, '15 Q7 Join Date: Feb 2007 Location: Woodstock, GA iTrader: (8)	The port may have reset to another one. Verify under Device Manager which port it is using.
	Appreciate 0 Quote

11-24-2007, 03:56 PM	#9
Tuned335i Major 24 Rep 1,310 Posts Drives: E92 335i Join Date: Jun 2007 Location: World of Torque iTrader: (0)	I had the same problem yesterday in my V2 install. I was using a serial cable however. Couldn't open the com Ports. I went back and looked at the V1.47 install instructions and it didn't say anything about messing with a com port setting. So I unplugged the cable from the laptop, shut down the PROcede software, plugged the cable back into the laptop, then ran the software again. I didn't go into the comms to change the port. I just clicked "go online/offline" in the comms menu and it worked. This may not work for you if using a USB cable though. __________________ Torque - The One You Love...
	Appreciate 0 Quote

11-24-2007, 04:25 PM	#10
M3to335 Whats that smell? 145 Rep 1,790 Posts Drives: Bimmers, duh Join Date: Nov 2006 Location: NC iTrader: (6)	I cant get my 6 foot cable to work, yet my 6 " cable works fine. Its really odd. On 1.47 It wasnt an issue. Im sure its all in my head, but its extremely ironic.
	Appreciate 0 Quote

11-24-2007, 04:26 PM	#11
NPDAN Colonel 95 Rep 2,573 Posts Drives: AW DCT M3 Join Date: Feb 2007 Location: So.Cal iTrader: (7) Garage List 2008 E92 M3 [8.00] 07' E92 335i [0.00]	un plug the serial and plug it back in. See if it will recognize new hardware... too hard to trouble shoot without being there. __________________
	Appreciate 0 Quote

11-24-2007, 05:04 PM	#12
HyperM3 Too many Alex's, from now on, call me Beaufort 342 Rep 6,188 Posts Drives: See Sig Join Date: Feb 2007 Location: Lawrenceville, NJ iTrader: (8)	Ok, so I pulled out my laptop and downloaded everything. Same thing started happening then all of a sudden we had "online" come up. We didnt even want to breathe on the car in case that set it off. Downloaded all the maps and everything in that regard went smooth. Now other issues. Started the car and BAM, it shut off after sputtering. Started it up again and it was good, then after a minute started sputtering again. Threw a LIMP CEL. I cleared the faults and started it up again. Did the same thing once again. So I cleared the faults and put the plugs on and took the PROced box out. Started fine and ran fine no problems. Now what? __________________ 13 HD FatBob 17 A4 Glacier/Black 1st Edition/Pre+/Sport/EurocodeTMD/Racechip 16 S6 (gone),14 S6 (gone),14 S6 (gone),13 S6 (gone),10 S4 (gone) 07 335i(gone)
	Appreciate 0 Quote

11-24-2007, 05:09 PM	#13
NPDAN Colonel 95 Rep 2,573 Posts Drives: AW DCT M3 Join Date: Feb 2007 Location: So.Cal iTrader: (7) Garage List 2008 E92 M3 [8.00] 07' E92 335i [0.00]	Did it start and run fine with the bypass plugs plugged in? __________________
	Appreciate 0 Quote

11-24-2007, 05:11 PM	#14
E90ice Banned 205 Rep 2,002 Posts Drives: 2008 335xi Coupe Join Date: May 2006 Location: WA iTrader: (0)	Wiring must be off. Check your wires. __________________
	Appreciate 0 Quote

11-24-2007, 05:15 PM	#16
bmwzimmer Major 35 Rep 1,084 Posts Drives: 335 Join Date: Jan 2007 Location: 91 octane states iTrader: (0)	do u have access to another laptop?
	Appreciate 0 Quote

11-24-2007, 05:32 PM	#18
e.n335 Moderator 270 Rep 4,481 Posts Drives: e93 ///M3 DCT, 07/2009 Join Date: Feb 2007 Location: Switzerland, ZH iTrader: (0)	Did you reset the car's ECU ?
	Appreciate 0 Quote

11-24-2007, 05:36 PM	#19
Terry335 Banned 96 Rep 2,587 Posts Drives: 335i Join Date: Jan 2007 Location: Socal iTrader: (0)	Try to connect to box again with laptop. If its cooked it probably won't connect.
	Appreciate 0 Quote