|
|
|
|
PLEASE HELP SUPPORT E90POST BY DOING YOUR TIRERACK SHOPPING FROM THIS BANNER, THANKS! |
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Pss 245/35/19, 275/30/19
|
|
Wheels and Tires forum Sponsored by The Tire Rack
Please help to directly support e90post by doing your tirerack shopping from the above link. For every sale made through the link, e90post gets sponsor support to keep the site alive. Disclaimer |
|
Thread Tools | Search this Thread |
03-18-2013, 10:46 AM | #1 |
Major
100
Rep 1,384
Posts |
Pss 245/35/19, 275/30/19
Wondering if I will rub. Reason I ask because I'm getting a good price on this set.
I'm running 19x8.5 et 30 front. 19x9.5 et 35 rear. Kw v2 on higher setting. -2 camber in rear. Will have -1.65 camber In front. Anyone running these sizes on e92 335? Or know if I will rub with these sizes? UPDATE: I went ahead with the 245/35/19 in the front and 275/30/19 in the rear. couldnt put them all up on my car yet because one of the rear wheels had a slight crack in it.. going to get it welded and summer setup will be up next weekend. but i test fitted one of the fronts on my car. I have about 2-3mm clearance between the new wider front tires and the front springs which i think should be good enough. the only rubbing i get is on the front of the tire against the front of the fender liner on full lock. which shouldnt be much of a problem i don't think. havent had the chance to test fit the rears yet but will most likely need a slight roll. UPDATE 2015: I have the tires on still and loving them. But i have them on 19x9et35 and 19x10et30 wheels now.. no rub issues but my camber in front is -2.4 (camber plates) and camber in rear is -2.1, had to do a fender trim in the back though,. Last edited by abhishriv; 01-28-2015 at 04:50 PM.. |
03-18-2013, 01:54 PM | #2 |
FBO WTF!
25
Rep 437
Posts |
You should be ok
__________________
V710 19x9.5 Square|H&R Sport Springs|6000k D1S|Blacklines|Procede v5|HKS BOV|Stett CP|BMS DCI|Raceland DP|BigTom IC|M2 Exhaust|AEM Meth|M3 Front Bumper| |
Appreciate
1
|
03-19-2013, 01:18 PM | #6 |
Banned
50
Rep 1,731
Posts |
You're fine. I'm running 255/35/19 and 295/30/19 PSS, rubs only on big bumps
|
Appreciate
0
|
03-20-2013, 06:37 AM | #7 |
Captain
37
Rep 738
Posts
Drives: E92/E63
Join Date: Nov 2011
Location: N.Ireland
|
I'm running 8.5 et37 (+5mm spacers) 245/35/19 fronts & 9.5 et30 275/30/19 rears dropped the whole way down on my coilovers with no rubbing or scrubbing at all
__________________
|
Appreciate
0
|
03-20-2013, 08:53 AM | #8 | |
Major
100
Rep 1,384
Posts |
Quote:
|
|
Appreciate
0
|
03-20-2013, 05:31 PM | #9 |
Captain
37
Rep 738
Posts
Drives: E92/E63
Join Date: Nov 2011
Location: N.Ireland
|
I got a set of Altenzo sport comforters, they were cheap and decent from reviews I'd read. Haven't had any trouble at all with them, looking to change up my wheels now though, only got the rims to do me a short while.
__________________
|
Appreciate
0
|
03-21-2013, 06:50 PM | #10 | |
Major
100
Rep 1,384
Posts |
Quote:
|
|
Appreciate
0
|
06-20-2013, 12:38 PM | #11 | |
Lieutenant Colonel
102
Rep 1,903
Posts
Drives: e92 335i 6MT
Join Date: May 2011
Location: Toronto
|
Quote:
|
|
Appreciate
0
|
07-02-2013, 05:10 PM | #12 |
Major
100
Rep 1,384
Posts |
nope no spacers needed. the front et is actually et35. just got alignment done so front camber is at -1.3 and rear is -2.0. even in the back only needed the least amount of roll, so little they didnt even charge me for it.
|
Appreciate
0
|
07-02-2013, 09:00 PM | #13 |
DIYER
614
Rep 5,521
Posts |
I am running a 35 offset with a 5MM spacer so it is essentially a 30 offset with a Nitto 245/30/20 and a -1.5 camber and no rub but had to modify a few things to wich is easy
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
|
Appreciate
0
|
07-03-2013, 09:50 AM | #14 |
Lieutenant Colonel
102
Rep 1,903
Posts
Drives: e92 335i 6MT
Join Date: May 2011
Location: Toronto
|
Nice, is that -1.3 front camber with stock strut mounts?
|
Appreciate
0
|
07-03-2013, 10:58 AM | #15 |
DIYER
614
Rep 5,521
Posts |
I run 295 Nitto with a 10MM spacer on my 20" setup but going to 19" and thought about going to PSS again (although I had better traction with Nitto, crazy I know) what offset are you runningI? I am sure you had to have a spacer to keep the rim off the strut/body...I had to but I am running a 10.5" rim so with the New 10" rim I may be okay....fenders are shaved...rear have the plastic pieces cut out where quarter panel/bumper meet ECT.
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
|
Appreciate
0
|
07-06-2013, 04:27 AM | #16 |
Banned
50
Rep 1,731
Posts |
I had weak offsets so it didn't pose an issue. rear fenders were rolled and shaved. rear offset was 38. I have since went "green" with lightweight rims with a smaller tire...but I miss the fat tire look.
|
Appreciate
0
|
07-06-2013, 05:20 PM | #17 |
DIYER
614
Rep 5,521
Posts |
With stg 3 VTT you better get the fat tires back!!!
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
|
Appreciate
0
|
07-06-2013, 09:09 PM | #18 |
Banned
50
Rep 1,731
Posts |
LSD will solve that for me , I'm running a PSS 275 and when these go, I plan on running AD08s which are wide as fcuk.
|
Appreciate
0
|
07-06-2013, 10:03 PM | #19 |
DIYER
614
Rep 5,521
Posts |
I spun 285 Nitto, PSS and spin 295 Nitto we will seer about PSS. The 295's do hook better though.
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
|
Appreciate
0
|
07-14-2013, 09:29 AM | #20 |
Banned
50
Rep 1,731
Posts |
Lol the 295 PSS hooks like a mofo. I do want to try AD08s, RE11s, or RS3s at some point. I do spin a lot more with the 275s without a doubt on the open diff.
|
Appreciate
0
|
07-14-2013, 02:27 PM | #21 |
DIYER
614
Rep 5,521
Posts |
Awesome!
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
|
Appreciate
0
|
07-15-2013, 12:58 AM | #22 |
Banned
50
Rep 1,731
Posts |
But I have a feeling in the pit of my stomach, youll manage to spin the PSS as well :P, 10mm difference isn't make or break and seeing how you have a LSD and lockdown kit...I may be very well screwed come September LOL.
Gonna have to get super wide body kit and stuff 335s like creaminz rofl. |
Appreciate
0
|
Bookmarks |
|
|