[Vicko]

Originally Posted by scottp999

It's gotta be something good since I told myself I wouldn't spend any more $ on mods this year. I'm sure you are going to do your best to open up my wallet (hoping meth kit).

[335Turbo]

Originally Posted by shiv@vishnu

I should be able to finish them this weekend and post them up on Monday or Tues.

Shiv

Have the new DD maps been posted for rev.1?

[RxBMW]

Does anyone knows what codes 10770 and 10771 means?

Thanks.

[lyjw88]

can I lower the Stage 1 UT setting to 70%?

[jpsimon]

sure, why?

[Andras]

When Shiv said that the latest firmware updated, the 117, was "BT friendly" what did he mean?
I recently experienced some problems with my BT, right after uploading 05/29 Stage3 map through firmware update #115.
What happened is that the condition base service is a mess.
My rear brakes' pads were to be replaced according to the last regular scan I had.
On the following I had it looked like also the front ones are to be replaced, but they're new!!!!!!!! And that was confirmed by BMW assistance, where I am now.
One more thing: when clearing codes on the I-drive appears a warning for some kind of ABS malfunctioning, it goes away right after codes are cleared.
Once again: if a BT scan is made with the car running V3 firmware update #115 is it possible that things get jammed?

[...]

^^^^
Convert to hex and search Bavauto DME Code pdf:

2A12 DMTL diagnosis module tank leakage,
magnetic valve, input signal
2A13 DMTL diagnosis module tank leakage,
leakage diagnosis pump, input signal

[scheherazade]

I'd still prefer steering wheel audio buttons for map changing.

1) You can display results on dash (right above where you're pressing)
2) I don't have homelink (LOL)

-scheherazade

[RxBMW]

Originally Posted by enfox

^^^^
Convert to hex and search Bavauto DME Code pdf:

2A12 DMTL diagnosis module tank leakage,
magnetic valve, input signal
2A13 DMTL diagnosis module tank leakage,
leakage diagnosis pump, input signal

Thanks man, the car have the service engine soon light on and do not let me run the code erasing process .

[lyjw88]

Originally Posted by jpsimon

sure, why?

I want my boost level to be around 12psi

[TheAcAvenger]

Originally Posted by lyjw88

I want my boost level to be around 12psi

My low boost map peaks at 11.5 or so on the gauge. It's closer to 45%. Even when I was stage 1.

[kptaylor]

In the V3.3 5-29 file for 6MT, why are there two PCD files for each stage? They both say Map1=Map2...

[Andras]

Originally Posted by Andras

When Shiv said that the latest firmware updated, the 117, was "BT friendly" what did he mean?
I recently experienced some problems with my BT, right after uploading 05/29 Stage3 map through firmware update #115.
What happened is that the condition base service is a mess.
My rear brakes' pads were to be replaced according to the last regular scan I had.
On the following I had it looked like also the front ones are to be replaced, but they're new!!!!!!!! And that was confirmed by BMW assistance, where I am now.
One more thing: when clearing codes on the I-drive appears a warning for some kind of ABS malfunctioning, it goes away right after codes are cleared.
Once again: if a BT scan is made with the car running V3 firmware update #115 is it possible that things get jammed?

up!
BTW
I updated the firmware to #117 version.
Would it be ok now to use the BT?

[gt3fever]

Originally Posted by Andras

up!
BTW
I updated the firmware to #117 version.
Would it be ok now to use the BT?

firmwire 117 is compatible for use of BT

[Andras]

Originally Posted by hipertech

firmwire 117 is compatible for use of BT

Ok, thanks for confirming.
My other point/question was to check out if the whole jam thing regarding Condition Base Service was due to the non-compatibility of firmware 115 with the BT or not........

[Tuned335i]

Preface: 2007 335i Coupe, pre-29.2, PROcede Rev I, DCI, Forge DVs, race gas mix - approx 95 octane.

Kinda late to the game here - too busy at work right now to keep up with E90Post.com, but I uploaded the pro01v03beta117.bin firmware and 5-29 Stage1_6AT map this afternoon and I want to report back that the reports from Rev I users are accurate. The boost is a bit quicker to pick up and it's definitely flat with none of the fluctuation that I had in the past. It's a nice improvement from the 2-19 map I have been driving.

I continue to have no codes whatsoever, shadow or otherwise, as reported with the BavarianTec Tool, Enthusiast Version. Coming up on two years with the PROcede installed (starting with V1.47) with no problems - love the tune.

[lyjw88]

I installed my first procede today and OMG!!!!!!!!!!!
The car is now a beast.

[Tuned335i]

Originally Posted by lyjw88

I installed my first procede today and OMG!!!!!!!!!!!
The car is now a beast.

Yup, that's a typical first response! Be judicious with your newfound supremacy!

[Vudoo4u2]

remember to soon turn your DTC off....or your rear brakes are going to get a run in with some serious usage

[lawdude]

To all who now have a beast:

Has it lowered your ETs and/or increased your trap speeds?

[Micks-e92]

Originally Posted by Grendalf

Are we going to be able to activate the valet mode also? That will be so nice

Does the valet mode work with the latest firmware, maps and software?

Thanks!

[edo]

Shiv, could you please at least make a keyboard shortcut to start/stop datalogging? It is really inconveniet to use touchpad mouse to start/stop datalogging... Especially when there's no passenger.