[AndyR83]

Hello,

I'm trying to learn to code my E92. I have a cable and just got my laptop in the mail today (running Win-7 Pro 32 bit.) I have been following this PDF guide and using this FAQ thread to guide me. I have successfully completed steps up to and including #37. After that, I have an issue.

Step 38: As directed, I press F1 then F3. The guide states I will be taken to a menu where I sleect my chassis type. This does not happen. Instead, I get the menu where I pick "CAS." When I do so, I get this error:



I assume it must be reading something, since the VIN number populates in the field you can see in the screenshot. What am I doing wrong here?

I have tried unplugging and re-plugging both ends of the cable, removing the key and restarting the entire process from scratch, restarting the laptop, and all the common troubleshooting stuff one might think to try in this situation. I can't think of anything else to try.


EDIT: I just saw the sticky thread that specifically states not to post screenshots of error messages. Trying to get my error log to post, sorry about that!

[AndyR83]

ERROR! Modul: A_E65CAS.IPS, Proc: FAread, LineNr: 49, ErrorNr: 2062
COAPI-2062: error during reading coding data
CAS, FA_LESEN: ERROR_ECU_INCORRECT_RESPONSE_ID

>> ERROR! Modul: COAPI2.CPP, Proc: coapiRunCabd, LineNr: 06, ErrorNr: 2062
FA_READ

>> ERROR! Modul: COAPI4.CPP, Proc: coapiReadAuftrag, LineNr: 04, ErrorNr: 2062
FA_READ: A_E65CAS

[cn555ic]

Make sure man file is empty and cleared of any data in the work folder

[icucCoding]

Update the daten files for E89. It looks like you were using the E65 files.

[AndyR83]

After lots of trial and error, I eventually figured out that the car was in the wrong "mode." When I took the key out, put it in, and tried without pressing the start/stop button to turn on accessories it worked. I had been pressing the button before attempting to connect, and it wouldn't work.

About an hour later, the daten file issue became apparent when I tried to code the KOMBI module, lol. I worked through it. So far, so good.

I'm left with two issues:

#1 I can't find the bulb checks to code them out. I went into the NFRM module where they should be but none of them are in there for me to change to nicht_aktiv.

#2 For some reason, my lane change indicator now only blinks once instead of 3 times when activated, though I never modified it intentionally.

[michbmw]

For Item #1 what year E90 do you have? or do you know if you have NFRM3? if so NFRM3 is a bit of a different animal

I could not find (i believe this is NFRM2):

KALTUEBERWACHUNG_BLK_V_R
KALTUEBERWACHUNG_BLK_V_L
WARMUEBERWACHUNG_BLK_V_R
WARMUEBERWACHUNG_BLK_V_L
FEHLERMELDUNG_CC_BLK_V_R
FEHLERMELDUNG_CC_BLK_V_L

And was instructed to code the following all to nicht_aktiv:

KALTUE_POL_M2_50_M1_8
KALTUE_FRA_V_M1_13_M2_40
KALTUE_NSL_M2_51_M1_10
WARMUE_POL_M2_50_M1_8
WARMUE_FRA_H_M2_45_M1_12
WARMUE_FRA_V_M1_13_M2_40
WARMUE_NSL_M2_51_M1_10

[AndyR83]

I have a 2008 E92. I'll go see if I have those.

[michbmw]

my 2010 has NFRM3, i don't know what a 2008 has though cn555ic may know

[cn555ic]

He definitely doesn't have those values u just posted as he as frm2. I already told him to look for

KALTUEBERWACHUNG
WARMUEBERWACHUNG.

That end in BL or Blk. Make all those nicht_aktiv

Then find all the

cc_Meldung

That also end in blk and bl and make those nicht_aktiv