yet ANOTHER VRSF fmic thread. 7" installed

nsx_modified · 07-12-2015, 09:36 PM

Hi all.

I know there have been a ton of posts regarding the VRSF fmic's. Not gonna post a install thread or anything like that. Just going to point a few pointers for anyone doing it in the future.

Read all the DIY's and you should be fine.

- as previous posters have mentioned, trimming the shroud will take the longest time. Had the bumper off (got a m3 eBay rep, will post a review after paint) saw the fan shroud and as others have posted rather than trim I just cut the whole front part off. It still took me a while as I didn't want to dremal off too much so I did inch my inch and kept test fitting.

That was really the only thing that took a while and it was a scorching day! 35 cel ( 95F)

Another problem I encountered was the silicone connectors kept popping off cause I couldn't secure it well enough. This was the silicone on the driver side - connecting to the lower charge pipe. I kept the stock one. Finally got it all tightened up.

I recommend tightening the upper connector to the lower charge pipe first. If you got the upgraded upper charge pipe you should have some wiggle room between the silicone connectors above to push it down a bit (I needed to). Once all that is fastened, connect silicone to driver side fmic.

That is all the pointers I have.

Enjoy.

[IMG][/IMG]

mike@x-ph.com · 07-13-2015, 04:12 PM

Congrats and thank you for the review

Tiago@VRSF · 07-13-2015, 04:13 PM

Nice review! Intercooler looks great installed on the car!

Jeff@TopGearSolutions · 07-13-2015, 05:21 PM

I think the Air conditioner has you beat on the heat exchanger aspect

nsx_modified · 07-13-2015, 05:29 PM

Lolol

I like the comparison. It's a good time for the IC, starting to get real hot!

BadDogmotorsports · 07-14-2015, 05:26 AM

looks great, thats a hot day for an install. You should defiantly notice a difference with the drop in IAT's you will be getting.

07-12-2015, 09:36 PM	#1
nsx_modified Private 2 Rep 77 Posts Drives: 2008 335i Join Date: Feb 2013 Location: Toronto iTrader: (2)	Dyno added Hi all. I know there have been a ton of posts regarding the VRSF fmic's. Not gonna post a install thread or anything like that. Just going to point a few pointers for anyone doing it in the future. Read all the DIY's and you should be fine. - as previous posters have mentioned, trimming the shroud will take the longest time. Had the bumper off (got a m3 eBay rep, will post a review after paint) saw the fan shroud and as others have posted rather than trim I just cut the whole front part off. It still took me a while as I didn't want to dremal off too much so I did inch my inch and kept test fitting. That was really the only thing that took a while and it was a scorching day! 35 cel ( 95F) Another problem I encountered was the silicone connectors kept popping off cause I couldn't secure it well enough. This was the silicone on the driver side - connecting to the lower charge pipe. I kept the stock one. Finally got it all tightened up. I recommend tightening the upper connector to the lower charge pipe first. If you got the upgraded upper charge pipe you should have some wiggle room between the silicone connectors above to push it down a bit (I needed to). Once all that is fastened, connect silicone to driver side fmic. That is all the pointers I have. Enjoy. [IMG][/IMG] Attached Images
	Appreciate 0 Tweet Quote

07-13-2015, 04:12 PM	#2
mike@x-ph.com BimmerPost Supporting Vendor 24180 Rep 190,777 Posts Drives: 07-335/12-328/18-M4/21-M4CP Join Date: Sep 2013 Location: Las Vegas iTrader: (23)	Congrats and thank you for the review __________________ Check out our current sale by clicking on this link! https://x-ph.com/sale/ Phone number 702-494-9435
	Appreciate 0 Quote

07-13-2015, 04:13 PM	#3
Tiago@VRSF 2095 Rep 43,350 Posts Drives: F90 M5 Join Date: Dec 2007 Location: Doral, FL iTrader: (99) Garage List 2014 F30 328xi [0.00] 2015 F82 BMW M4 [0.00] 2013 Ducati 1199 Pa ... [0.00] 2008 BMW 335i [0.00]	Nice review! Intercooler looks great installed on the car! Last edited by Tiago@VRSF; 07-13-2015 at 05:26 PM..
	Appreciate 0 Quote

07-13-2015, 05:21 PM	#4
Jeff@TopGearSolutions 3441 Rep 79,211 Posts Drives: C6 Z06, 09 335i, 10 335xi Join Date: Dec 2008 Location: www.TopGearSolutions.com iTrader: (37)	I think the Air conditioner has you beat on the heat exchanger aspect
	Appreciate 0 Quote

07-13-2015, 05:29 PM	#5
nsx_modified Private 2 Rep 77 Posts Drives: 2008 335i Join Date: Feb 2013 Location: Toronto iTrader: (2)	Lolol I like the comparison. It's a good time for the IC, starting to get real hot!
	Appreciate 0 Quote

07-14-2015, 05:26 AM	#6
BadDogmotorsports Captain 17 Rep 627 Posts Drives: 335i Join Date: Jun 2014 Location: Massachusetts iTrader: (3)	looks great, thats a hot day for an install. You should defiantly notice a difference with the drop in IAT's you will be getting.
	Appreciate 0 Quote