|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
RB/OEM turbo install thread:
|
|
11-13-2012, 12:37 AM | #1 |
DIYER
610
Rep 5,521
Posts |
RB/OEM turbo install thread:
Been searching a lot on the web for install hints, tips, pics Ect (if this is posted somewhere delete this) and would have loved to find all of this in one spot so decided to post some links (have more but do not know if it is allowed LOL!!) here and hope other who have done this install can contribute as well. Anthing about this install is good (What to do first, second, what not to do ect): Rob beck did say NOT to go crazy on the bolt on the coolant/oil feed lines...they do not need much force.
Big thanks to "Rob Beck" & "M3Tuner" for there help & advice during this install thus far! Thread of mine with some good reference pics also: http://www.e90post.com/forums/showthread.php?t=768812 other install pics/threads: http://www.e90post.com/forums/showthread.php?t=598323 http://www.e90post.com/forums/showthread.php?t=692077 Torque specs: Bracket to cylinder head: 9Nm = (6.6 ft lbs) Coolant supply line to crankcase: 9Nm = Coolant return line to crankcase: 8Nm = (5.9 ft lbs) Coolant return line to turbo: 8Nm = (5.9 ft lbs) Coolant supply line to supply line: 8Nm = (5.9 ft lbs) Exhaust manifold heat shield: 8Nm = (5.9 ft lbs) Oil supply line to crankcase: 20Nm = (14.8 lbs) Oil pressure line to turbo: 8Nm = (5.9 ft lbs) Oil return line to crankcase: 8Nm = (5.9 ft lbs) Oil return line to turbo: 8Nm = (5.9 ft lbs) Turbo manifold to head: 20Nm = (14.8 lbs) (found this to be a bit high went with about 13 lbs)
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
Last edited by robc1976; 11-24-2012 at 03:07 AM.. |
11-16-2012, 07:51 AM | #2 |
DIYER
610
Rep 5,521
Posts |
When doing the install I have found the following so far:
1. Remove the fan/FMIC to make water-pump removal easier 2. Install a new water pump/thermostat at time of install 3. Subframe does not need to be dropped (rob beck also confirmed this). 4. Have multiple jacks 5. Wear googles (not kidding) 6. Get replacement manifold studs, they will pull out. I have to loose a entire day because I did not do this. 7. Good time to clean your FMIC (see pic of tool below) 8. Will need a thin walled 1/4" drive 10MM socket or shave one down like I did below. 9. 3 Cans of parts cleaner to clean all oil & coolant lines (VERY important) plus all other parts. 10. 2 gallons of your choice of anti-freeze (I use 50/50 prestone extended life). 11. 7 quarts of motor oil of yor choice (I use Mobile 1 0W-40 European car formula). 12. Label everything! 13. This is my go to tool for O2 sensors, did a RB turbo install with it and over 10 dp installs...makes it so easy LOL!! Cut off the end with a dremel so you can get clearance and still have leverage.
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
Last edited by robc1976; 12-06-2012 at 02:51 PM.. |
Appreciate
0
|
11-18-2012, 03:52 PM | #3 |
DIYER
610
Rep 5,521
Posts |
Snap this pic to save some others headaches, when I took the coolant lines off the OEM turbos I must have pryed on the flange and it slight bent it and when installed on the RB's W/spacers it caused a gap. I fixed it by reinstalling the lines on the turbos and tightening down and bending flange back (do not do this with Rbs since it could strip the threads). I rather strip a OEM than a RB LOL!!!
I get what to do now, there are 2 spacers (1 for bolt stud & 1 for the line)....the upper line is made to seat into the stock turbo ( longer) so when you put the lines in on the RB flat flange there is a gap because it can not sink in. Big thanks to: "cstavaru" for his input
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
Last edited by robc1976; 11-19-2012 at 01:02 PM.. |
Appreciate
0
|
11-18-2012, 09:34 PM | #4 |
DIYER
610
Rep 5,521
Posts |
Good time to get all the dents out of your FMIC with this awesome liitle tool:
If you want more than 20psi from your RB's you will need this: If using JB4 you haver to make this setting "pic provided my Steve. Kroda"
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
Last edited by robc1976; 12-07-2012 at 06:46 PM.. |
Appreciate
0
|
11-19-2012, 10:12 PM | #8 |
DIYER
610
Rep 5,521
Posts |
As am I basically, 2 mins away....I met up with him to get my turbos....great guy to say the least. I am seeing a lot more peop,e from here on E90....group meet?? Lol!!!
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
|
Appreciate
0
|
11-19-2012, 10:13 PM | #9 |
DIYER
610
Rep 5,521
Posts |
I will for sure!!
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
|
Appreciate
0
|
11-20-2012, 03:15 AM | #10 |
DIYER
610
Rep 5,521
Posts |
Found out that a regular 10 MM socket or wrench has a bit of a tough time fitting on the "Front turbos" Coolant line nut, so instead of getting a thin walled socket a shaved down a 10MM 1/4" drive socket and it worked like a charm LOL!!
Here is a comparision of a regular socket and shaved socket going on the nut, as you can see a regular socket hits. Some reference pics of the lines Front turbo front: Front turbo rear: Rear turbo front: Rear turbo rear: Most people may know this but the tow hook can be used to lift the motor also...when on a jack it is pretty easy to lift the motor left and right to line up motor mounts by hand: You can get this device if you want to support it from top with the tow hook: http://www.harborfreight.com/1000-lb...bar-96524.html
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
Last edited by robc1976; 11-23-2012 at 05:37 PM.. |
Appreciate
0
|
11-20-2012, 07:12 AM | #11 |
Colonel
130
Rep 2,490
Posts
Drives: 2007 E92 SG 335i 6MT
Join Date: Apr 2011
Location: SW Florida
|
Wow
Good read OP, thanks for the info!
__________________
|
Appreciate
0
|
11-20-2012, 08:34 AM | #13 |
Major
237
Rep 1,041
Posts |
Woah, I'm guessing that isn't your hand in the pic with the sockets? I mean its cool if it is, i'm not judging, but I would personally go for something slightly more subtle
__________________
E92 335i 6MT | Balloon White | Black Dakota Leather - Sold
PROcede Rev3 V5 | AE Quad Exhaust | BMW Performance Short Shift Kit | Gunmetal 19" M3 GTS Wheels | BF Goodrich g-Force T/A KDW 2 | AST 4100 Coilovers | Swift Springs F:280 R:560 | ER Charge Pipe | Tial Blue BOV | VRSF 3" Downpipes | VRSF 7" Intercooler http://www.e90post.com/forums/showthread.php?t=782212 |
Appreciate
1
VonBimmer10.50 |
11-20-2012, 09:01 AM | #14 | |
I even mod my cereal
242
Rep 3,437
Posts
Drives: 11 ZCP DCT M3 14 328d 21 GT4
Join Date: Aug 2009
Location: Northern Va
|
Quote:
but seriously, thanks Rob for putting this together.....great detailed shots of why this install is only for professionals.
__________________
2011 Mineral White M3 ZCP - Opticoat, Ventureshield, some CF, B&B exhaust, AFE Intake Vorsteiner VFF 101s Ohlins
2014 Mineral White 328d Xdrive Wagon - Opticoat, Ventureshield, B8s, H&R, Apex SM-10s Hawk Pads 2021 718 Cayman GT4 - Fire extinguiser |
|
Appreciate
0
|
11-20-2012, 01:26 PM | #15 |
DIYER
610
Rep 5,521
Posts |
roflmao!!!! That s my wife's nails....little does she know they are going to get a lot dirtier from helping me align the motor mounts
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
|
Appreciate
0
|
11-20-2012, 01:26 PM | #16 |
DIYER
610
Rep 5,521
Posts |
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
|
Appreciate
0
|
11-20-2012, 01:50 PM | #17 |
DIYER
610
Rep 5,521
Posts |
Added ft lb. values to first post
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
|
Appreciate
0
|
11-20-2012, 02:38 PM | #19 |
DIYER
610
Rep 5,521
Posts |
More on the way!! Get ready to put them on, going on is much easier than taking these off.
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
|
Appreciate
0
|
11-20-2012, 03:31 PM | #20 |
DIYER
610
Rep 5,521
Posts |
New parts came in!!
Water pump/thermostat: V-band clamps: Very important to get all gasket material out of the head:
__________________
JB4 G5, Stage 3 LPFP, Stage 2 MOTIV PI, VM 6466 ST, Custom OCC W/ SS lines, ER FMIC, ER CP W/HKS BOV, M3 control arms, M3 guide rods, M3 upper links, M3 front & rear sway-bars, HPA rear toe arms, Wavetrac LSD, HPF Gen 2, DEFIV kit, KW clubsport, Delrin solid SF bushings, stoptech rotors, Rogue Tranny Mounts, 1M bumper, M3 CF hood, M3 fenders, M3 OEM sideskirts, Mtech rear bumper, CSL trunk, MORR VS8.2 rims 245/295
|
Appreciate
0
|
11-20-2012, 03:40 PM | #21 |
Mad Linux Guru On The Loose
1112
Rep 5,391
Posts
Drives: 2008 335i Sedan, 2023 M3
Join Date: Aug 2009
Location: Chicago, IL
|
I am liking this.
Can you give us more info on how you lift/support the engine with the tow hook please? Did you have to disconnect the engine from the transmission?
__________________
6MT | COBB | AR | AE | Forge DV | HPF | P3 Gauge | Hybrid Intake | O.S.Giken TCD | All M3 bits | TCKLine | StopTech | UUC | ER | SPEC
|
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|