|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
VK Oil Cooler Review: Track Tested
|
|
06-16-2009, 09:21 AM | #1 |
Brigadier General
2753
Rep 4,445
Posts |
VK Oil Cooler Review: Track Tested
VK Oil Cooler Review.
Install: Not the easiest project to complete without a lift, but it’s doable. Make sure you have at least 7 quarts of oil handy, some “oil clean-up” and rags just in case things get messy (which happened in my case). I had an issue with one of the hoses (which may have been user error), so I had two hoses made at the local hydraulics store and Vince split the cost with me. The first time install took me 4-5 hours, now I can swap the OEM oil cooler back on in about an hour and install the VK oil cooler in nearly the same time. When you remove the OEM cooler, make sure the O rings from the OEM hoses are not left behind in the thermostat entrance. Lay some rags just below the OEM hoses to catch any oil that may fall when you disconnect the OEM hose. Make sure you have a thin-walled 13 mm socket as well, I had to go to the hardware store to pick this up because all of my sockets were too thick. Also, an adjustable wrench makes the job much easier. I added nearly a quart of oil after the swap, which is about right considering the oil remaining in the OEM hoses and OEM oil cooler. I used some permatex high temp race thread sealant for all connections. Shipping: Kudos to Vince for a superb wrapping job, almost too good. When you see this oil cooler it screams quality. I blew out the cooler with compressed air and was happy to see it was free from debris. The oil cooler came in two business days from ordering.When you compare the VK oil cooler with OEM you can't help but laugh at the size difference. Performance: I’ll set the scene for you, a nearly 4 mile road course with ambient track temperatures inching near 103F, UV index of 14 with high humidity. Under normal circumstances I wouldn’t run, but I had just completed my custom cool-shirt system V2 with 19 QT capacity, so worst case scenario I would be comfortable running in a "pace car" with pulled timing. Wow! The N54 is an extraordinary engine when it's happy and cool. Typically, with cooler ambient temps, three laps in I’d be hitting 280-290F oil temps. Well, I was just below 250F. So I turned it up a notch and started dropping into a lower gear in turns I would normally not bother due to temps. Temps went to 255-260F and stayed there with no power loss. Second session, I ran with some Porsche guys and the car did terrific. In the past, the timing would get pulled after lap 2, but this time, the power stayed on lap after lap. I was running personal best times and after 15 minutes temps hovered around 260-270. Then, I started getting greedy by holding high revs (something I would never do in the past). Finally, at the 28th minute of the 30 minute session oil temps hit 275-280, power was getting pulled but not because of the oil temps, the coolant temps had spiked despite running nearly straight distilled. One cool down lap, brought oil temps back below 250F. Conclusion: The VK Oil Cooler works period! Triple digit temps with 14 UV index and the product perfromed. My only regret is, I waited so long to add this modification. I'm not an easy person to please, but Vince has brought a great product to market and in my opinion is a must-do mod for anyone tracking an N54. Nice work Vince.
__________________
Last edited by Bubbles; 06-16-2009 at 11:50 AM.. |
06-16-2009, 09:57 AM | #3 |
General
290
Rep 28,154
Posts |
worst part of that job is routing the hoses and getting them aligned correctly so you dont strip the hose or adapters. them hoses wont bend in tight spaces lol
|
Appreciate
0
|
06-16-2009, 10:11 AM | #4 | |
Brigadier General
2753
Rep 4,445
Posts |
Quote:
It's funny you mentioned that because it's true. The hoses I bought were a bit more flexible to work with and I added about 1.5 inches to both. In hindsight, .75 inch extension would do it.
__________________
|
|
Appreciate
0
|
06-16-2009, 10:16 AM | #6 |
General
290
Rep 28,154
Posts |
yea i made new hoses myself, we got the wrong setup in the kit, but mine werent much more flexible, had to mount the hoses to the cooler before mounting the cooler to the car to make it easier instead of trying to manipulate the hoses
|
Appreciate
0
|
06-16-2009, 11:46 AM | #9 |
Professional Moose Racer
316
Rep 7,509
Posts |
Great review, I need ones of these OC'ers as a stand alone since I dont have one from the factory
__________________
Visit my blog anytime: http://www.sfpayments.com
BMW Dream Team PNW Chapter, member #1 |HP Autowerks | AR DESIGN | BMW PERFORMANCE | STOP TECH | Volk Racing| AMS | ARKYM |
Appreciate
0
|
06-16-2009, 11:51 AM | #10 |
General
290
Rep 28,154
Posts |
|
Appreciate
0
|
06-16-2009, 12:29 PM | #11 |
Brigadier General
670
Rep 4,959
Posts |
Nice review Bubbles. It seems that a high capacity oil cooler is almost a must if one intends to do some serious tracking.
BTW, does the VK Oil Cooler kit use the same model Setrab Oil Cooler that the Dinan kit uses?
__________________
Current: '23 G20 M Sport 330i
Current: '20 X253 GLC300 SUV Gone: '20 W205 C43 Sedan Gone: '18 W205 C43 Sedan Gone: '13 W204 C63 Sedan |
Appreciate
0
|
06-16-2009, 01:34 PM | #12 | |
Brigadier General
2753
Rep 4,445
Posts |
Quote:
Biz....it looks nearly identical
__________________
|
|
Appreciate
0
|
06-16-2009, 02:45 PM | #13 |
Major General
125
Rep 8,745
Posts |
So, I guess both an upgraded radiator and upgraded oil cooler required for track!
__________________
SB, Terra, 6MT. Only a few mods here and there.....nothing extreme!
|
Appreciate
0
|
06-16-2009, 03:30 PM | #14 | |
Brigadier General
2753
Rep 4,445
Posts |
Quote:
Yes, then suspension...you get the picture...
__________________
|
|
Appreciate
0
|
01-27-2010, 10:52 AM | #17 |
Lieutenant Colonel
148
Rep 1,738
Posts |
We are using specially made Goodyear hoses that are much more flexiable. I have a few units in stock for $595 PM me if your interested.
|
Appreciate
0
|
01-27-2010, 11:01 AM | #18 |
3441
Rep 79,212
Posts
Drives: C6 Z06, 09 335i, 10 335xi
Join Date: Dec 2008
Location: www.TopGearSolutions.com
|
Great review...
I have a question for those who know: Does the OEM oil cooler have a thermostat control to only kick on at near 250 degrees? ( I heard that somewhere) Does the VK oil cooler have a thermomstat to kick on sooner, maybe at 215? As you guys might know, oil viscosityis rated at 215 degrees, I cant believe BMW has these cars running 250? TIA |
Appreciate
0
|
01-27-2010, 11:03 AM | #19 | |
Moderator
270
Rep 4,481
Posts |
Quote:
|
|
Appreciate
0
|
01-27-2010, 11:07 AM | #20 |
www.facebook.com/Synergy69
24
Rep 505
Posts |
link and pics to said oil cooler kit please!
|
Appreciate
0
|
01-27-2010, 11:11 AM | #21 | |
3441
Rep 79,212
Posts
Drives: C6 Z06, 09 335i, 10 335xi
Join Date: Dec 2008
Location: www.TopGearSolutions.com
|
Quote:
Thats more or less what im looking to hear. My specific question I guess quite simply was, what temp is the thermostat said to kick on stock (havnt really found an exact number) for the OIL cooler OEM. And, does the VK oil cooler have this thermostat to come on sooner (at a lower temp)? Sounds like it does if you average temps in the 212 range, thats where I'd like to have my car sit personally. Might have to put VK OC on the list |
|
Appreciate
0
|
Bookmarks |
|
|