|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Having trouble installing FF wires 11 N55
|
|
09-04-2014, 09:37 PM | #1 |
Fastest 335 on Earth
39
Rep 426
Posts |
Having trouble installing FF wires 11 N55
Trying to install flex fuel wires on my friends N55.
Having a problem. Once everything is connected the car runs weird, half check engine light. SES light. When you hit the buttons down to go into the JB4 menu the car stumbles and stalls after a couple of seconds. I went over the wiring 3-4 times, re-did the connector a bunch of times. The car runs perfect when the stock harness is plugged in. Once it's connected to the JB4 harness..it gets all screwed up. I changed the "Fuel Open Loop" to 50 on the JB4 interface. What that correct? Any help would be great. Thank you
__________________
E92 335i, 6MT- YouWish Single turbo, Precision 6466, Doc Race intake manifold w/port injection, Precision Raceworks coil packs and Stage 3 lpfp, 3.46 geared Mfactory LSD, VRSF 3.5" single exhaust, Toyo R888Rs, Spec Stage 3+ clutch, DSS axles, RTD shifter, Motiv, boost box and flex fuel, WOTBOX, MOTIV tuned...and much more
|
09-04-2014, 10:06 PM | #2 |
Captain
121
Rep 653
Posts |
Did you update the firmware and cut the diode for ISO? Not sure if you can run FF wires w/o updating the jb4 firmware and changing all recommended settings for ISO. I did mine all at once, without being ISO FF wires really aren't needed unless boosting more than 16 psi from what I understand. Also I had a similar issue when one of the pins on the job harness was slightly backing out and causing a CEL. Looked connected when I went over all the wiring but when I dis connected harness and pulled on wires individually I saw the loose pin. Hope that helps
__________________
2012 DCT 135i
PURE S2 JB4/mhd Fuel-It! direct port meth injection check out my youtube channel here |
Appreciate
0
|
09-04-2014, 10:24 PM | #3 |
Fastest 335 on Earth
39
Rep 426
Posts |
Yes i updated the firrmware and it was already iso.
__________________
E92 335i, 6MT- YouWish Single turbo, Precision 6466, Doc Race intake manifold w/port injection, Precision Raceworks coil packs and Stage 3 lpfp, 3.46 geared Mfactory LSD, VRSF 3.5" single exhaust, Toyo R888Rs, Spec Stage 3+ clutch, DSS axles, RTD shifter, Motiv, boost box and flex fuel, WOTBOX, MOTIV tuned...and much more
|
Appreciate
0
|
09-05-2014, 05:14 AM | #4 |
First Lieutenant
44
Rep 394
Posts |
|
Appreciate
0
|
09-05-2014, 08:15 AM | #5 |
Lieutenant Colonel
245
Rep 1,595
Posts
Drives: 2011 335i xDrive Msport
Join Date: Apr 2013
Location: Orlando
|
That and make sure you cut and intercepted the other wires correctly. It is possible to screw both of those up. I think I put this on your FB post too.
|
Appreciate
0
|
09-05-2014, 08:20 AM | #6 | |
Brigadier General
1161
Rep 3,185
Posts |
Quote:
|
|
Appreciate
0
|
09-05-2014, 09:16 AM | #7 |
Banned
329
Rep 1,739
Posts |
Sounds like something isn't wired properly - or maybe the connections aren't clean.
Are you positive that the diode was cut? Are you sure that you have the pin going through the correct hole? |
Appreciate
0
|
09-16-2014, 04:03 PM | #9 |
Lieutenant Colonel
245
Rep 1,595
Posts
Drives: 2011 335i xDrive Msport
Join Date: Apr 2013
Location: Orlando
|
What is the bump for, to get a resolution report?
|
Appreciate
0
|
09-17-2014, 02:18 PM | #11 |
Lieutenant Colonel
245
Rep 1,595
Posts
Drives: 2011 335i xDrive Msport
Join Date: Apr 2013
Location: Orlando
|
Words are good. They help explain your intentions. Instead of "bump" you could have said "what did you find out with this?" So people didn't wonder WTF you are talking about since the point where the thread left off was in the middle of troubleshooting.
|
Appreciate
0
|
09-17-2014, 03:14 PM | #12 |
Lieutenant
42
Rep 412
Posts |
haha this is exactly what i was thinking... thought i was in the classified section again!
|
Appreciate
0
|
09-19-2014, 05:55 PM | #14 |
Fastest 335 on Earth
39
Rep 426
Posts |
bump
__________________
E92 335i, 6MT- YouWish Single turbo, Precision 6466, Doc Race intake manifold w/port injection, Precision Raceworks coil packs and Stage 3 lpfp, 3.46 geared Mfactory LSD, VRSF 3.5" single exhaust, Toyo R888Rs, Spec Stage 3+ clutch, DSS axles, RTD shifter, Motiv, boost box and flex fuel, WOTBOX, MOTIV tuned...and much more
|
Appreciate
0
|
09-20-2014, 12:29 AM | #16 |
Colonel
1972
Rep 2,711
Posts |
Contact jon@burgertuning.com for support
|
Appreciate
0
|
Bookmarks |
|
|