|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Search | Today's Posts | Mark Forums Read |
|
BMW 3-Series (E90 E92) Forum
>
**627WHP@22.5psi** Vishnu/FFTEC Single Turbo System Dyno Session #3 (PROcede Tuned)
|
|
02-22-2012, 07:04 AM | #45 |
Lieutenant Colonel
55
Rep 1,690
Posts |
|
Appreciate
0
|
02-22-2012, 07:24 AM | #48 |
Banned
270
Rep 5,876
Posts |
Oh SNAP! Amazing what this motor holds, this is crazy stuff...great work Shiv
Would you run out of fuel down low if you upped boost earlier? I know piggies had issues before in richening AFRs early on in the RPMs...i guess you'll be able to show that with a smaller turbo |
Appreciate
0
|
02-22-2012, 07:48 AM | #50 |
Colonel
291
Rep 2,898
Posts |
Fantastic work.
Really looking forward to getting out from warranty on my 1M so I can go wild. Ideally, I'd like a small(er) turbo with quick spool-up and a broad, flat torque curve that could run on 93 octane with no meth. Not really concerned about peak #s as much as a nice fat area under the curve. Neil |
Appreciate
0
|
02-22-2012, 07:52 AM | #51 |
Hellafunctional
37
Rep 426
Posts |
I'm not sure if it has been mentioned, but what model turbo is this?
Also, will this void the warranty....oh, and what spring should i get?
__________________
Go: Cobb S2+, Big Tom FMIC, CP-E DP & DCI, Royal Muffler, AR OC Turn: TC Kline/Swift SA, Vorshlag Plates, UUC Front Bar, H&R M3 Rear Bar, VAC endlinks & spacers, Forgeline 18x9.5/NT05 265 Square Stop: Endless MX72, Stoptech Rotors/Lines, Motul RBF600 |
Appreciate
0
|
02-22-2012, 07:59 AM | #52 |
Brigadier General
133
Rep 4,764
Posts |
Very nice. Congrats.
|
Appreciate
0
|
02-22-2012, 07:59 AM | #53 |
Banned
270
Rep 5,876
Posts |
How's this running to 22.5psi on the stock 2.5bar tmap sensor? 2.5bar - 1bar for atmospheric you get 1.5bar measurable boost at sea level, so 21.7-21.8psi...did you already plug in a 3bar?
Oh, and would you mind posting the datalog and AFR trace... |
Appreciate
0
|
02-22-2012, 08:10 AM | #54 |
Private
19
Rep 97
Posts |
This is incredible. Way to go Shiv! I know many will disagree but whats the point in going any further? 600-700 is more than anyone needs. I feel like its at the point where the reward to risk trade-off is sketchy. Although I know the procedes is doing a great job of keeping things safe I just feel going any further will cause stuff to wear faster and cause mechanical failure.... But I could be wrong!
|
Appreciate
0
|
02-22-2012, 08:11 AM | #56 | |
Banned
270
Rep 5,876
Posts |
Quote:
|
|
Appreciate
0
|
02-22-2012, 08:20 AM | #57 | |
First Lieutenant
27
Rep 313
Posts |
Quote:
|
|
Appreciate
0
|
02-22-2012, 08:29 AM | #58 |
.
660
Rep 1,059
Posts |
I'd like to see a retune and the resulting graph where boost is ramped up normally, ie. as quick as possible. I understand the reasoning behind ramping it up like a NA engine (drivetrain protection), but to me, that's not the point of a big turbo. By nature, the bigger turbo should hit full spool much later than the little twins, but still come on hard enough that you get rocked into the back of your seat. That's a high WTQ/WHP big turbo experience for me... not a slow gradual increase where peak boost hits at 6500 RPM.
If snapping axles or destroying tranny gears is the concern, then I'd say this size turbo isn't optimal for the car as a whole, despite the N54 being able to manage it without issue. |
Appreciate
0
|
02-22-2012, 08:31 AM | #59 | |
Enlisted Member
0
Rep 40
Posts |
Quote:
The intercooler pressure drop off is around 0,7-0,8 psi ,so the tmap sensor is reading arround 21.7-21.8 . Is that right? |
|
Appreciate
0
|
02-22-2012, 08:42 AM | #61 |
Colonel
83
Rep 2,291
Posts |
Ridiculous
I did not think this motor would handle this much on stock internals... With race gas, you guys might be touching 700 WHP. What is the PSI limit of this turbo ? Great job Shiv and company!
__________________
2jZ + RB26 + 4G63 + LS9 + N54 =
|
Appreciate
0
|
02-22-2012, 08:56 AM | #62 |
Colonel
142
Rep 2,661
Posts |
Speechless
__________________
|
Appreciate
0
|
02-22-2012, 09:26 AM | #64 |
honda/acura O.G.
66
Rep 38
Posts |
great great job can't wait for this kit to sell to the public. just a quick question, with this kit what are you using for meth mixture, nozzle size, and is it a 150,200, or 250 psi pump? |
Appreciate
0
|
02-22-2012, 09:29 AM | #65 | |
Banned
270
Rep 5,876
Posts |
Quote:
at sealevel take 1bar off that and you get 1.5bar of measuring range which is 21.7556607psi...unless he's below sea level Last edited by dzenno; 02-22-2012 at 09:36 AM.. |
|
Appreciate
0
|
02-22-2012, 09:34 AM | #66 |
Banned
270
Rep 5,876
Posts |
Weird...timing this 60-130 looks to be in the 7s? Where's that extra power going? You should be well into the 6s...7s are RB territory...that's weird...vbox it!
|
Appreciate
0
|
Bookmarks |
Thread Tools | Search this Thread |
|
|