|
|
|
|
|
|
BMW Garage | BMW Meets | Register | Today's Posts | Search |
|
BMW 3-Series (E90 E92) Forum
>
Best agent to remove sticky stuff =)
|
|
08-18-2009, 07:07 PM | #1 |
Major
274
Rep 1,088
Posts |
Best agent to remove sticky stuff =)
So my car had this huge dealership emblem on the trunk just to the left of the license plate. I finally had the chance to remove it this weekend with dental floss. The emblem is larger than a quarter coin and now there is a huge spot of sticky residue which I can't wash away.
I can think of GooGone but have never use it before. Do you guys have any other recommendation? Thanks. |
08-18-2009, 07:24 PM | #2 |
Colonel
148
Rep 2,932
Posts |
Goo-gone, wd-40, 3m Adhesive remover should all do the trick. Make sure to not apply too much pressure to prevent marring the paint and rewax the area as all those solvents will remove any wax or sealant you may have.
__________________
|
Appreciate
0
|
08-18-2009, 07:33 PM | #3 |
Major
274
Rep 1,088
Posts |
|
Appreciate
0
|
08-18-2009, 08:08 PM | #4 |
Lieutenant Colonel
126
Rep 1,893
Posts |
i just debadged my car today, i used some degreaser spray i found in my garade. i dont know if its recommended but it worked, and it looks great. i guess any degreaser would work
|
Appreciate
0
|
08-18-2009, 08:47 PM | #5 |
Smiling politely
165
Rep 7,931
Posts |
Goes without saying, but put the stuff on a soft cloth to apply it. Don't spray it directly on your car.
__________________
E90 330i Black Sapphire 6MT | 991.1 C4 Platinum Silver 7MT
|
Appreciate
0
|
08-18-2009, 09:40 PM | #6 |
Major General
122
Rep 6,594
Posts |
And make sure you re-apply some sealant/wax on the area after everything is gone. Most of these products will strip the protection off paint.
__________________
X7 LCI // Incoming C7 ZR1 ZTK // Sebring + TRX // Hydro + Raptor Gen1 Roush // Tuxedo |
Appreciate
0
|
10-15-2010, 01:48 PM | #9 |
Registered
0
Rep 1
Posts |
FRUSTRATED
My 2006 BMW 320i is now out of motorplan with 109 000 Kilometers.the last service was 99 000 kilos and now the remaining kilos for next service is 3200.yesterday it failed to start.I ran its check system, it noted OK(the oil level ok,spug plucks ok e.t.c.I open the oil lid and I discovered a that the oil very dirty and sticky, i used my finger to test it. Now my question is should I do engine flush?
|
Appreciate
0
|
10-16-2010, 10:56 AM | #10 |
Learning "The Art"
8
Rep 116
Posts |
I would use more of automotive based adhesive remover. Goo gone will work but is a little harsh. Every detailing manufacturer makes a adhesive remover which the normally call solvent or new car solvent. The cheapest way for you to do this may be to just stop by your local detail shop and ask them to remove the glue. If you came to my shop Id do it for free, then talk you into a detail. lol
|
Appreciate
0
|
10-16-2010, 11:02 AM | #11 |
First Lieutenant
15
Rep 299
Posts |
I have used nail polish remover in the past and works like a champ. When u complete removing the glue or the sticky stuff make sure u seal and wax the area like mentioned above.
__________________
|
Appreciate
0
|
10-16-2010, 11:14 AM | #12 | |
I ask the questions you're afraid to ask.
44
Rep 2,489
Posts |
Quote:
There are much better and safer products out there - like 3M Adhesive Remover or goo gone that are less likely to damage paint. |
|
Appreciate
0
|
10-16-2010, 11:09 PM | #14 | |
Colonel
148
Rep 2,932
Posts |
Quote:
__________________
|
|
Appreciate
0
|
10-17-2010, 06:15 AM | #15 | |
Captain
11
Rep 770
Posts |
Quote:
|
|
Appreciate
0
|
10-17-2010, 03:04 PM | #16 | ||
Banned
27
Rep 872
Posts |
Quote:
Quote:
Your car's paint won't be affected by these as it is chemically cured and will not be affected by these solvents. This can't be said if you have an old-school or cheap paint job that is lacquer: lacquer never cures, it only dries. Hence why you can use lacquer thinner to remove this type of paint. In short, 3M Adhesive remover (which I'd recommend for this job) is just a slightly weaker solvent than acetone AKA nail polish remover. Both should work fine. The only issue is to make sure to keep it away from rubber or plastic trim. |
||
Appreciate
0
|
Bookmarks |
|
|