Procede v5 8-26 Maps/Firmware available!

mjp · 09-18-2011, 10:57 PM

Quote:

Originally Posted by shiv@vishnu

Are you sure you have a Rev2.5 or Rev3? Rev2 will still trigger that code from time to time regardless of what map you run.

Not sure, how would I know what rev the unit is? The instructions say that rev2.5/3 maps will not work on a rev2 unit so I assume I have a 2.5.

Is there any way to check what rev the unit is?

shockin330i · 09-18-2011, 11:53 PM

Just did a quick mexico run with the new maps

mjp · 09-19-2011, 03:32 AM

I found this info that Shiv posted. Mine unit was shipped out on the 24th of May 2011. What I do not understand is that the car started up fine with me loading the 2.5 maps.

Quote:

Originally Posted by shiv@vishnu
Here's the gist on rev2 hardware evolution:

1) Rev2a... what 99.99% of you have
2) Rev2b... what only the most recent (late May onwards) rev.2 buyers have. Same as Rev.2 but with a revised fuel control circuit allowing for a larger +/- 3 point AFR adjustment. Useful for those running upgraded turbos. Completely unnecessary for anyone else.
3) Rev2.5... as above but with upgraded ignition control hardware. Useful for all users. Especially for those who routinely run race gas/meth.

So if you fall into the 99.99% category and have a Rev2a, the Rev2.5 hardware update with give you the revised fuel control circuit as well as the upgraded ignition control hardware.

And if you are in the .01% of users had have a rev2b, the Rev2.5 update will update only your ignition control hardware.

With this update, a Rev2.5 is (in terms of engine control) IDENTICAL to a Rev3. The only relevant differences is the absence of the extra i/o and native USB. Something that I suspect most people can live without.

The advantage of running a Rev3 (over a Rev2.5) is most profound for those running non-sport (130mph limit) 6MTs running PWM meth since you can retain your speed delimit AND run PWM methanol AND take advantage of the 2-step limit and flat-foot shift.

The advantage of running a Rev.3 (over a Rev2.5) is least profound for those running 6AT without PWM meth since you can delimit speed (if desired) AND 2-step/flat-foot shift isn't feasible.

Cheers
Shiv

Pepe_pr · 09-19-2011, 07:49 AM

Shocking your car is holding boost very nice. Nice vid

TN_3 · 09-19-2011, 02:07 PM

So if I have Procede that was purchased in Nov. 2010, and all I have done is update the fuel harness, then I should have Rev. 2?

Slops · 09-19-2011, 02:34 PM

i picked up a nice serial to usb cable from shiv's link.

CPWINCH · 09-19-2011, 02:35 PM

Shockin your hitting about 14 psi. What mods and octane.

shockin330i · 09-19-2011, 02:44 PM

Quote:

Originally Posted by CPWINCH

Shockin your hitting about 14 psi. What mods and octane.

drop in and downpipe. I was running ms109 I was in map 1 which I put 14 max. I should have been on map 2 with 16psi. A my bad on my behalf. But the car held boost.

GiRtHyN55 · 09-19-2011, 03:02 PM

Ok I have reloaded the 8-26 firmware and maps car seemed to be fine. Did the resets and went to go get gas...engine malfunction reduced power. I drove the car back to my job (bmw) it felt fine the whole way back. Reset the procede again and the warning went away for now but the procede has 3 fault codes stored 12170 10847 12253. Kinda not sure what to do next im pretty sure the warning will come back on. Im running the latest BMW software i updated my DME this past sat. I dont think my usb cable is the issue cause its never given me a problem before...any ideas?

TreDirtyFive · 09-19-2011, 03:03 PM

Quote:

Originally Posted by shockin330i

drop in and downpipe. I was running ms109 I was in map 1 which I put 14 max. I should have been on map 2 with 16psi. A my bad on my behalf. But the car held boost.

holdin boost strong there mang!

MJR63 · 09-19-2011, 03:10 PM

Loaded the new maps and firmware successfully the other night. Overall very smooth power and my hiccups shifting from 2 - 3 and 3 -4 (6MT) that I experienced with the last beta have gone away. Although I did notice some hiccups on the highway while going 80+ when I needed boost. Shiv any suggestions? Thanks!

Jalndrs · 09-19-2011, 03:12 PM

Quote:

Originally Posted by shockin330i

drop in and downpipe. I was running ms109 I was in map 1 which I put 14 max. I should have been on map 2 with 16psi. A my bad on my behalf. But the car held boost.

With the new maps I am holding 15 on map 2. DP, Drop In, and 93 Shell. Car feels amazing.

Slops · 09-19-2011, 03:24 PM

Quote:

Originally Posted by GiRtHyN55

Ok I have reloaded the 8-26 firmware and maps car seemed to be fine. Did the resets and went to go get gas...engine malfunction reduced power. I drove the car back to my job (bmw) it felt fine the whole way back. Reset the procede again and the warning went away for now but the procede has 3 fault codes stored 12170 10847 12253. Kinda not sure what to do next im pretty sure the warning will come back on. Im running the latest BMW software i updated my DME this past sat. I dont think my usb cable is the issue cause its never given me a problem before...any ideas?

maybe something legit is wrong with the car. I dont know what those codes mean so maybe you should contact Shiv to see if he can iron out anything from the procede side. If that doesn't work, then maybe put the car back to stock and see if you still get the same issues?

GiRtHyN55 · 09-19-2011, 03:31 PM

Quote:

Originally Posted by Sloppy

maybe something legit is wrong with the car. I dont know what those codes mean so maybe you should contact Shiv to see if he can iron out anything from the procede side. If that doesn't work, then maybe put the car back to stock and see if you still get the same issues?

Well when i reload the 8-8 Beta firmware and maps the car is ok

So something isnt going right when i put the updated maps

Pepe_pr · 09-19-2011, 03:33 PM

ok guy's i did the upload and everithing went smooth. did a small drive and feels good. wierd that this maps there is no FMIC special map??? any reason?

i will do some hard pulls tonigth and see how it performs.

Pepe_pr · 09-19-2011, 03:35 PM

Quote:

Originally Posted by GiRtHyN55

Well when i reload the 8-8 Beta firmware and maps the car is ok

So something isnt going right when i put the updated maps

are you sure u updated the firmware first and then the maps?

re-upload the firmware (5.0060 and then the maps 8-26) . that should take care of the issue.

Slops · 09-19-2011, 03:37 PM

Quote:

Originally Posted by Pepe_pr

are you sure u updated the firmware first and then the maps?

re-upload the firmware (5.0060 and then the maps 8-26) . that should take care of the issue.

ahhh good call

GiRtHyN55 · 09-19-2011, 03:54 PM

Quote:

Originally Posted by Pepe_pr

are you sure u updated the firmware first and then the maps?

re-upload the firmware (5.0060 and then the maps 8-26) . that should take care of the issue.

Yes im sure i did the firmware first loaded the pro5v006.bin file first then the 6mt maps. Reset all 12-1 waited a few seconds and started the car

ian2002525 · 09-19-2011, 03:54 PM

Quote:

Originally Posted by TN_3

So if I have Procede that was purchased in Nov. 2010, and all I have done is update the fuel harness, then I should have Rev. 2?

yes you have Rev2

GiRtHyN55 · 09-19-2011, 04:24 PM

So far so good ....keeping my fingers crossed lol

CPWINCH · 09-20-2011, 02:01 AM

shiv whens the turbo upgrade coming out

Slops · 09-21-2011, 04:35 PM

are there any more updates from you guys with the new maps?

09-18-2011, 11:53 PM	#68
shockin330i Brigadier General 798 Rep 4,784 Posts Drives: 2016 ZCP M3 Join Date: Jan 2007 Location: f y'all, I'm from Texas (RGV) iTrader: (1)	Just did a quick mexico run with the new maps __________________ ERnie 2016 BSM/f80/ZCP
	Appreciate 0 Quote

09-19-2011, 07:49 AM	#70
Pepe_pr Lieutenant 35 Rep 553 Posts Drives: 135i black on black Join Date: Sep 2010 Location: San Juan PR iTrader: (1)	Shocking your car is holding boost very nice. Nice vid __________________ USED TO HAVE A 385 whp 479 tq N55 335 2011 (AT) AND NOW A 135 M package 2010 (AT) 447whp/504tq
	Appreciate 0 Quote

09-19-2011, 02:07 PM	#71
TN_3 Major 341 Rep 1,352 Posts Drives: 2018 M3 CS Join Date: Oct 2007 Location: Franklin, TN iTrader: (10) Garage List 2020 BMW X5 M50i G05 [0.00] 2018 BMW M3 CS F80 [0.00]	So if I have Procede that was purchased in Nov. 2010, and all I have done is update the fuel harness, then I should have Rev. 2? __________________ 2018 M3 CS F80 l SMB l EXEC 2020 X5 M50i G05 l MW l BLACK l PREM l DHP l 22” l PARK l EXT S-LINE l LASER l TH l AG
	Appreciate 0 Quote

09-19-2011, 02:34 PM	#72
Slops Major General 188 Rep 5,417 Posts Drives: 2005 C55 AMG Join Date: Jan 2011 Location: Oxford iTrader: (2)	i picked up a nice serial to usb cable from shiv's link.
	Appreciate 0 Quote

09-19-2011, 02:35 PM	#73
CPWINCH Brigadier General 732 Rep 4,635 Posts Drives: Toyota Prius Join Date: May 2010 Location: Los Angeles iTrader: (7)	Shockin your hitting about 14 psi. What mods and octane. __________________ Follow my BMW instagram @CARMODIFICATION Let me know you are from bimmerpost and i'll follow back
	Appreciate 0 Quote

09-19-2011, 03:02 PM	#75
GiRtHyN55 Private 4 Rep 92 Posts Drives: 2011 335xi Join Date: Dec 2010 Location: white plains, ny iTrader: (0) Garage List 2011 335 x drive [0.00]	Ok I have reloaded the 8-26 firmware and maps car seemed to be fine. Did the resets and went to go get gas...engine malfunction reduced power. I drove the car back to my job (bmw) it felt fine the whole way back. Reset the procede again and the warning went away for now but the procede has 3 fault codes stored 12170 10847 12253. Kinda not sure what to do next im pretty sure the warning will come back on. Im running the latest BMW software i updated my DME this past sat. I dont think my usb cable is the issue cause its never given me a problem before...any ideas? __________________ 2011 Black 335 xi MT- M package- Cold weather- BMW Performance Grills-PIAA H8 yellow fogs-Procede V5-Vishnu DP 3.5 inch- CDV delete-Vishnu Charge Pipe - *Waiting on meth kit* - H&R Springs Sport Kit
	Appreciate 0 Quote

09-19-2011, 03:10 PM	#77
MJR63 Lieutenant 21 Rep 415 Posts Drives: 2011 335i X-Drive Sedan Join Date: Sep 2010 Location: Tolland, CT iTrader: (5) Garage List 2011 BMW 335i x-drvie [0.00]	Loaded the new maps and firmware successfully the other night. Overall very smooth power and my hiccups shifting from 2 - 3 and 3 -4 (6MT) that I experienced with the last beta have gone away. Although I did notice some hiccups on the highway while going 80+ when I needed boost. Shiv any suggestions? Thanks!
	Appreciate 0 Quote

09-19-2011, 03:33 PM	#81
Pepe_pr Lieutenant 35 Rep 553 Posts Drives: 135i black on black Join Date: Sep 2010 Location: San Juan PR iTrader: (1)	ok guy's i did the upload and everithing went smooth. did a small drive and feels good. wierd that this maps there is no FMIC special map??? any reason? i will do some hard pulls tonigth and see how it performs. __________________ USED TO HAVE A 385 whp 479 tq N55 335 2011 (AT) AND NOW A 135 M package 2010 (AT) 447whp/504tq
	Appreciate 0 Quote

09-19-2011, 04:24 PM	#86
GiRtHyN55 Private 4 Rep 92 Posts Drives: 2011 335xi Join Date: Dec 2010 Location: white plains, ny iTrader: (0) Garage List 2011 335 x drive [0.00]	So far so good ....keeping my fingers crossed lol __________________ 2011 Black 335 xi MT- M package- Cold weather- BMW Performance Grills-PIAA H8 yellow fogs-Procede V5-Vishnu DP 3.5 inch- CDV delete-Vishnu Charge Pipe - *Waiting on meth kit* - H&R Springs Sport Kit
	Appreciate 0 Quote

09-20-2011, 02:01 AM	#87
CPWINCH Brigadier General 732 Rep 4,635 Posts Drives: Toyota Prius Join Date: May 2010 Location: Los Angeles iTrader: (7)	shiv whens the turbo upgrade coming out __________________ Follow my BMW instagram @CARMODIFICATION Let me know you are from bimmerpost and i'll follow back
	Appreciate 0 Quote

09-21-2011, 04:35 PM	#88
Slops Major General 188 Rep 5,417 Posts Drives: 2005 C55 AMG Join Date: Jan 2011 Location: Oxford iTrader: (2)	are there any more updates from you guys with the new maps?
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search