[enrita]

Originally Posted by Devas

A friend if mine just installed CP-E catless downpipes with stock exhaust . His idle and pre 2500rpm is very throaty. He is running stage 2+ aggressive. Is there anyway forvhim to get rid of that?

Yeah put back stock dps...

[enrita]

Originally Posted by statelax3

dumb cobb question here. i am in NC and have my emission inspection due august 1st. is there a map for stage0 and a dp fix? any one passed the sniffer with catless dp's?

Get atr, you can activate the code delete. Sniffer should be fine with secondary on . Readiness .. Not sure.

[Devas]

Originally Posted by enrita

Yeah put back stock dps...

How about Cp-E Catted Downpipes?

[enrita]

Originally Posted by Devas

How about Cp-E Catted Downpipes?

This has nothing to do with cobb thread, anyway i am against catted dps so would say get AR resonated dps.

[Devas]

Originally Posted by enrita

This has nothing to do with cobb thread, anyway i am against catted dps so would say get AR resonated dps.

Well it does, since when he was running Stage 1 Aggressive, there wasn't much throatyness from 600 - 2500 rpm..Only started when we put on V401 Stage 2+ Aggressive

[enrita]

Originally Posted by Devas

Well it does, since when he was running Stage 1 Aggressive, there wasn't much throatyness from 600 - 2500 rpm..Only started when we put on V401 Stage 2+ Aggressive

So with cpe dps and stage 1 aggr. There was no throatyness?
Stage 2+ has much more load / boost which gives than better sound .

[805beemer]

Originally Posted by enrita

Get atr, you can activate the code delete. Sniffer should be fine with secondary on . Readiness .. Not sure.

I have atr and found the dtc toggles under advanced parameters. How would I make a stock map that wont trigger the cat codes so I can run my jb4 without canclear on? Are all the codes listed cat codes? P29f4, P29f5 p2d25, p2f6c, p2fa3?

[benzy89]

Originally Posted by Devas

Well it does, since when he was running Stage 1 Aggressive, there wasn't much throatyness from 600 - 2500 rpm..Only started when we put on V401 Stage 2+ Aggressive

You won't see any of the DP gains while running Stage 1, running Stage 2 or Stage+FMIC if you're catless.

Originally Posted by 805beemer

I have atr and found the dtc toggles under advanced parameters. How would I make a stock map that wont trigger the cat codes so I can run my jb4 without canclear on? Are all the codes listed cat codes? P29f4, P29f5 p2d25, p2f6c, p2fa3?

Why? Stage 2 cancels out the DP/emissions related codes. I'm assuming that you're looking to run a Stock COBB tune w/ the JB4 to get readiness for an OBD emissions testing? Here are all the possible DP related codes:

• P0040 O2 Sensor Signals Swapped Bank 1 Sensor 1/ Bank 2 Sensor 1
• P0041 O2 Sensor Signals Swapped Bank 1 Sensor 2/ Bank 2 Sensor 2
• P0130 O2 Sensor Circuit Malfunction (Bank 1 Sensor 1)
• P0131 O2 Sensor Circuit Low Voltage (Bank 1 Sensor 1)
• P0132 O2 Sensor Circuit High Voltage (Bank 1 Sensor 1)
• P0133 O2 Sensor Circuit Slow Response (Bank 1 Sensor 1)
• P0134 O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)
• P0135 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
• P0136 O2 Sensor Circuit Malfunction (Bank 1 Sensor 2)
• P0137 O2 Sensor Circuit Low Voltage (Bank 1 Sensor 2)
• P0138 O2 Sensor Circuit High Voltage (Bank 1 Sensor 2)
• P0139 O2 Sensor Circuit Slow Response (Bank 1 Sensor 2)
• P0140 O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 2)
• P0141 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
• P0142 O2 Sensor Circuit Malfunction (Bank 1 Sensor 3)
• P0143 O2 Sensor Circuit Low Voltage (Bank 1 Sensor 3)
• P0144 O2 Sensor Circuit High Voltage (Bank 1 Sensor 3)
• P0145 O2 Sensor Circuit Slow Response (Bank 1 Sensor 3)
• P0146 O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 3)
• P0147 O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 3)
• P0150 O2 Sensor Circuit Malfunction (Bank 2 Sensor 1)
• P0151 O2 Sensor Circuit Low Voltage (Bank 2 Sensor 1)
• P0152 O2 Sensor Circuit High Voltage (Bank 2 Sensor 1)
• P0153 O2 Sensor Circuit Slow Response (Bank 2 Sensor 1)
• P0154 O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 1)
• P0155 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 1)
• P0156 O2 Sensor Circuit Malfunction (Bank 2 Sensor 2)
• P0157 O2 Sensor Circuit Low Voltage (Bank 2 Sensor 2)
• P0158 O2 Sensor Circuit High Voltage (Bank 2 Sensor 2)
• P0159 O2 Sensor Circuit Slow Response (Bank 2 Sensor 2)
• P0160 O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 2)
• P0161 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 2)
• P0162 O2 Sensor Circuit Malfunction (Bank 2 Sensor 3)
• P0163 O2 Sensor Circuit Low Voltage (Bank 2 Sensor 3)
• P0164 O2 Sensor Circuit High Voltage (Bank 2 Sensor 3)
• P0165 O2 Sensor Circuit Slow Response (Bank 2 Sensor 3)
• P0166 O2 Sensor Circuit No Activity Detected (Bank 2 Sensor 3)
• P0167 O2 Sensor Heater Circuit Malfunction (Bank 2 Sensor 3)
• P1127 Exhaust Not Warm, Downstream O2 Sensor
• P1128 Upstream Heated O2 Sensors Swapped
• P1129 Downstream Heated O2 Sensors Swapped
• P0420 Catalyst System Efficiency Below Threshold (Bank 1)
• P0421 Warm Up Catalyst Efficiency Below Threshold (Bank 1)
• P0422 Main Catalyst Efficiency Below Threshold (Bank 1)
• P0423 Heated Catalyst Efficiency Below Threshold (Bank 1)
• P0424 Heated Catalyst Temperature Below Threshold (Bank 1)
• P0426 Catalyst Temperature Sensor Range/Performance (Bank 1)
• P0427 Catalyst Temperature Sensor Low Input (Bank 1)
• P0428 Catalyst Temperature Sensor High Input (Bank 1)
• P0430 Catalyst System Efficiency Below Threshold (Bank 2)
  P0431 Warm Up Catalyst Efficiency Below Threshold (Bank 2)
• P0432 Main Catalyst Efficiency Below Threshold (Bank 2)
• P0433 Heated Catalyst Efficiency Below Threshold (Bank 2)
• P0434 Heated Catalyst Temperature Below Threshold (Bank 2)
• P0436 Catalyst Temperature Sensor Range/Performance (Bank 2)
• P0437 Catalyst Temperature Sensor Low Input (Bank 2)
• P0438 Catalyst Temperature Sensor High Input (Bank 2)
• P1420 Catalyst Temperature Sensor Failure
• P1421 Catalyst Damage
• P0170 Fuel Trim Malfunction (Bank 1)
• P0171 Fuel Trim too Lean (Bank 1)
• P0172 Fuel Trim too Rich (Bank 1)
• P0173 Fuel Trim Malfunction (Bank 2)
• P0174 Fuel Trim too Lean (Bank 2)
• P0175 Fuel Trim too Rich (Bank 2)

[805beemer]

It would be nice to use cobb just to clear the cat codes so that I wont have to use canclear on the jb4. With canclear on if I ever get a limp mode, check engine light, ect. the code will be erased unless you quickly switch to map 0. And i don't want to stack the jb4 on top of stage 2 maps and blow up my car.

[benzy89]

Why not just use the COBB tune alone? Especially since ATR has been released and you can basically get all the benefits currently available on the JB4. And with the COBB you'll be able to instantly view any codes that get thrown & they won't get automatically erased erased (so you'll be able to identify & diagnosis any problems you're having)

[dfv2]

Originally Posted by benzy89

Why not just use the COBB tune alone? Especially since ATR has been released and you can basically get all the benefits currently available on the JB4. And with the COBB you'll be able to instantly view any codes that get thrown & they won't get automatically erased erased (so you'll be able to identify & diagnosis any problems you're having)

You know not what you speak, JB4 offers *way* more than a flash tune (meth integration, gauge hacking, etc). I'm gay as a rainbow for cobb and think the JB4 is a stud when it comes to features.

[benzy89]

Originally Posted by dfv2

You know not what you speak, JB4 offers *way* more than a flash tune (meth integration, gauge hacking, etc). I'm gay as a rainbow for cobb and think the JB4 is a stud when it comes to features.

With ATR or an ATP tune, you get meth integration. You'll also be able to tune for aftermarket turbos, race gas and/or E85. So really the only "major" feature that the JB4 has is gauge hijacking, which IMHO isn't a landmark "selling point" for a tune.

And I know that empirical data isn't and shouldn't be the deciding factor for what is the "best" tune, but COBB has the data that illustrates that that they are the most consistent & best performing tunes

[enrita]

Originally Posted by 805beemer

I have atr and found the dtc toggles under advanced parameters. How would I make a stock map that wont trigger the cat codes so I can run my jb4 without canclear on? Are all the codes listed cat codes? P29f4, P29f5 p2d25, p2f6c, p2fa3?

just open the stock map with ATR and uncheck all of those and also activate the speed delimeter than save it and flash it. Thats what i run now for jb4 G5 and CANclear OFF
If you open stage 2 map you will see what has been done there in terms of advanced options.
here dipfix and Speed delimiter.


i have also lowered timings by 1 degree

[805beemer]

Originally Posted by enrita

just open the stock map and uncheck all of those and also activate the speed delimeter . Thats what i run now for jb4.
If you open stage 2 map you will see what has been done there in terms of advanced options.

perfect, thank you

[new2the3]

In my log posted on the last page, is my afr ok?

[Lulz_M3]

Originally Posted by new2the3

In my log posted on the last page, is my afr ok?

Yep.

[D_Smiderreen]

I'm not sure if this has been suggested in this thread.....BUT is it possible to integrate some type of warning indicators in the AP itself or program the AP to turn on an audible alarm in the car?

An example would be, if timing went negative a past a user defined threshold, the turn signals would flash or the door chime would be activated. Maybe the screen on the AP could flash red or something?

Is anything like this possible with the AP?

[lorddrinkalot]

What boost should I run with Stage1+ Sport and Stage1+ aggressive?

[enrita]

Originally Posted by lorddrinkalot

What boost should I run with Stage1+ Sport and Stage1+ aggressive?

the one you get from the maps. its load based

[benzy89]

Originally Posted by D_Smiderreen

I'm not sure if this has been suggested in this thread.....BUT is it possible to integrate some type of warning indicators in the AP itself or program the AP to turn on an audible alarm in the car?

An example would be, if timing went negative a past a user defined threshold, the turn signals would flash or the door chime would be activated. Maybe the screen on the AP could flash red or something?

Is anything like this possible with the AP?

Guessing you're asking this to make sure you don't do any damage to the car? The COBB flashes the DME for a higher performance setting while maintaining and actively using the stock safety measures (knock prevention, timing adjustments, etc). If the tune becomes too aggressive & the DME considers the operating conditions to be dangerous, the engine will reduce power and probably throw a CEL/SES light.

Originally Posted by lorddrinkalot

What boost should I run with Stage1+ Sport and Stage1+ aggressive?

Not sure what you mean, but I'm guessing that you mean how much boost should you expect with Stage 1+ Sport/Aggressive, in which case you should be seeing something between 14-16 psi. Unless you're using ATR or getting a ProTuned map, users don't have control over the boost that's dialed into the OTS Maps.

[lorddrinkalot]

ok because some guys in the german board say that by boost with Stage 1+ Sport is way to high.

Attached 1 log over 3rd, 4th, 5th and 6th gear and one with 3rd gear only!

[lorddrinkalot]

@benzy89:

I have about 1,2 bar = 18PSI

That would be too much than!

But only in 3rd gear. in 4th and above its 16PSI